Hook up Memory Client reset of the Video Decoder to the decoders DT node.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This DTS file have initial support Samsung SGH-T959P phone,
also known as Samsung Galaxy S 4G or fascinate4g. It belongs to Samsung
Aries devices family.
Initial version have support for:
- sdcard
- max8998 pmic and rtc
- max17040 fuel gauge
- gpio keys
- fimd (no panel driver yet)
- usb (peripherial mode)
- wifi
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This DTS file have initial support Samsung Galaxy S phone, also known as
i9000. It belongs to Samsung Aries devices family.
Initial version have support for:
- sdcard
- internal memory
- max8998 pmic and rtc
- max17040 fuel gauge
- gpio keys
- fimd (no panel driver yet)
- usb (peripherial mode)
- wifi
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This DTS file have initial support Samsung Aries based phones.
Initial version have support for:
- sdcard
- internal memory (present only on non 4g variant)
- max8998 pmic and rtc
- max17040 fuel gauge
- gpio keys
- fimd (no panel driver yet)
- usb (peripherial mode)
- wifi
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Adds missing interrupt-controller property to gph2 block,
to silence following warnings during build:
/soc/pinctrl@e0200000/gph2: Missing interrupt-controller or interrupt-map property
It's reguired by Samsung Aries boards, an S5PV210 based
Samsung Galaxy S (i9000) and Galaxy S 4G phones, which are added in next patches.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Commit 2f28e4c24b (thermal: armada: Clarify control registers
accesses) introduced the new thermal binding. The new binding extends
the second registers field size to 8. Switch to the new binding to fix
thermal reading values. Without this change the fix for errata #132698
introduced in commit 8c0b888f66 (thermal: armada: Change sensors trim
default value) has no effect.
Cc: stable@vger.kernel.org # v4.16+
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Fixes for omap for v4.18-rc cycle
Few dts fixes for regressions for various SoCs and
devices for touchscreen wake, dra7 USB quirk, pinmux
for beaglebone mmc, and emac clock.
Also included is a change for ti-sysc to use kcalloc
that Kees wanted to get into v4.18 as that's the last
one he wanted to fix for improved defense against
allocation overflows.
* tag 'omap-for-v4.18/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap3: Fix am3517 mdio and emac clock references
ARM: dts: am335x-bone-common: Fix mmc0 Write Protect
bus: ti-sysc: Use 2-factor allocator arguments
ARM: dts: dra7: Disable metastability workaround for USB2
ARM: dts: am437x: make edt-ft5x06 a wakeup source
Signed-off-by: Olof Johansson <olof@lixom.net>
The enabling of the EMAC was reverted as there was an issue on how
to handle the integrated PHY and it was getting close to the release
window (fe45174b72 ("arm: dts: sunxi: Revert EMAC changes")).
When a solution was found, then the changes were restored in
4b236a0fe5 ("arm: dts: sunxi: h3/h5: Restore EMAC changes") and
4904337fe3 ("ARM: dts: sunxi: Restore EMAC changes (boards)").
Unfortunately enabling for the Beelink X2 was missed.
This reverts partially commit 6b0e06df5c (Revert "ARM: dts:
sun8i: h3: Enable dwmac-sun8i on the Beelink X2")
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
i.MX fixes for 4.18, round 2:
- A couple of imx defconfig updates selecting USB ULPI support to fix
a regression seen with USB driver, which is caused by commit
03e6275ae3 ("usb: chipidea: Fix ULPI on imx51").
- A fix on imx51-zii-rdu1 board touchscreen pinctrl setting, which
causes an interrupt storm.
* tag 'imx-fixes-4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx_v4_v5_defconfig: Select ULPI support
ARM: imx_v6_v7_defconfig: Select ULPI support
ARM: dts: imx51-zii-rdu1: fix touchscreen pinctrl
Signed-off-by: Olof Johansson <olof@lixom.net>
Currently the following DTC warnings are seen with W=1:
arch/arm/boot/dts/imx51-babbage.dtb: Warning (unique_unit_address): /usbphy/usbphy@0: duplicate unit-address (also used in node /usbphy/usbh1phy@0)
arch/arm/boot/dts/imx51-eukrea-mbimxsd51-baseboard.dtb: Warning (unique_unit_address): /usbphy/usbphy@0: duplicate unit-address (also used in node /usbphy/usbh1phy@0)
Fix it by moving the USB PHY nodes outside of simple-bus and drop the
unneeded unit-address, which matches the bindings documentation
at Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt
While at it rename the USB PHY node to usbphy1 for consistency.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The OPP properties, like "operating-points", should either be present
for all the CPUs of a cluster or none. If these are present only for a
subset of CPUs of a cluster then things will start falling apart as soon
as the CPUs are brought online in a different order. For example, this
will happen because the operating system looks for such properties in
the CPU node it is trying to bring up, so that it can create an OPP
table.
Add such missing properties.
Fix other missing properties (like clocks, supply, clock latency) as
well to make it all work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A previous patch removed OMAP clock aliases that were perceived
to be unnecessary. Unfortunately, it broke the ethernet on the
am3517-evm. This patch enables the MDIO clock and EMAC clock.
Fixes: 0ed266d7ae ("clk: ti: omap3: cleanup unnecessary clock aliases")
Cc: stable@vger.kernel.org #4.16+
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The AM3517-evm has a single USB Host port connected to hsusb1.
This patch enables that USB port.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DT specifications do not allow the underscore character in alias names.
Replace all underscores in alias names by dashes.
Signed-off-by: Felix Brack <fb@ltec.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This enables the Bluetooth on the wl1271 available in some models
of the AM3517-SOM from Logic PD.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Certain models of the AM3517 SOM from Logic PD come with an
integrated WL1271 WiFi. This patch enables the WiFi.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The tsadc is used to read various voltages on the board, so enable it
to be able to read these voltages from userspace.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the label for all LEDs, we made a mistake setting the label names on
all LEDs, where says green should say red, and viceversa, where says red
should be green.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
audio-graph-card is recommended for audio bindings. Let's change to it and
improve the support by adding the Amplifier configuration and the clock
enable control.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Production hardware will go with the DS1339 RTC chip, so replace the old
for the new one and also add the nIRQ pin to be able to properly wakeup
the system from suspend.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board can be either a host, or a peripheral, so set the controller as
OTG mode to reflect this.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the pins used by the LCD controller, the panel-info and display-timings
information for the MIDAS displays connected to the board. There are
two displays in the board, and these, are connected to the LCD controller
through a FPGA, so the timings and the resolution is what expects the FPGA,
not the MIDAS displays.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
phy-phandle is now a preferred method to reference a PHY device. The new
method also allows you to specify a reset gpio which is required for
this board.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates the backlight nodes to improve the support and describe
better how hardware is done. The changes done were:
* Use PWM_POLARITY_INVERTED instead of the hardcoded number.
* Add pinctrl configuration.
* Add the enable gpio definition.
* Add the power supply definition.
* Add more brightness levels.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The default value of 5ms will use GPIO hardware based debounce clocks
that will keep L4PER from idling consuming about extra 30mW.
Use a value of 10ms that is above the hardware debounce maximum of
7.95ms forcing software based debouncing.
This allows droid4 to enter PER retention during idle as long as UARTs
are idled and USB modules unloaded or unbound.
Note that there seems to be a pending issue with having droid 4 enter core
retention during idle where GPIO bank 1 needs to be reset late after init
for some reason to not block core retention. In addition to that, we are
also missing GPIO related PM runtime calls for omap4 that will be posted
separately.
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
By reconfiguring few GPIOs in the dts file we can make duovero parlor
hit retention during idle:
1. Let's a larger debounce value for gpio-keys
This will then make gpio-keys use software debounce and the GPIO
debounce clock is not enabled.
2. Let's allow WLAN suspend for mwifiex
This can be done just by adding keep-power-in-suspend.
3. Let's reconfigure smsc911x driver to use GPIO edge interrupt
This will allow using NFSroot while the system idles, and the kernel
has quite a few dts files with "smsc,lan9115" compatible using edge
interrupts.
Then to have the system hit core retention during idle, the UARTs
needs to be idled and USB modules need to be unloaded or unbound.
Cc: Ash Charles <ash@gumstix.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The wl1835mod.pdf data sheet says this pretty clearly for WL_IRQ line:
"WLAN SDIO out-of-band interrupt line. Set to rising edge (active high)
by default."
And it seems this interrupt can be optionally configured to use falling
edge too since commit bd763482c8 ("wl18xx: wlan_irq: support platform
dependent interrupt types").
On omap4, if the wlcore interrupt is configured as level instead of edge,
L4PER will stop doing hardware based idling after ifconfig wlan0 down is
done and the WL_EN line is pulled down.
The symptoms show up with L4PER status registers no longer showing the
IDLEST bits as 2 but as 0 for all the active GPIO banks and for
L4PER_CLKCTRL. Also the l4per_pwrdm RET count stops increasing in
the /sys/kernel/debug/pm_debug/count.
While there is also probably a GPIO related issue that needs to be
still fixed, this change gets us to the point where we can have L4PER
idling.
I'm guessing wlcore was at some point configured to use level interrupts
because of edge handling issues in gpio-omap. However, with the recent
fixes to gpio-omap the edge interrupts seem to be working just fine.
Let's change it for all omap boards with wlcore interrupt set as level.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Eyal Reizer <eyalr@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Nishanth Menon <nm@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
[tony@atomide.com updated comments a bit for gpio issue]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board has USB VBUS detection available over GPIO. Plug it to
extcon node of USB1 and USB2 ports.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board has USB VBUS detection available over GPIO. Plug it to
extcon node of USB1 and USB2 ports.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Both ports on the dra7-evm and related boards can be used
as dual-role ports. Although we don't enable dual-role mode
for USB2 port let's add the necessary extcon bits to it.
Move the common portion of extcon_usb2 into dra7-evm-common.dtsi
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Dual-role support was added in v4.12. We should be using
it for USB2 port on the am57xx-idk.
Cc: <stable@vger.kernel.org> [4.16+]
Reported-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Fix other missing properties (clocks, supply, clock latency) as well to
make it all work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Fix other missing properties (clocks, supply, clock latency) as well to
make it all work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to i.MX6 datasheet, the LDO_1P1's typical
programming operating range is 1.0V to 1.2V, and
the LDO_2P5's typical programming operating range
is 2.25V to 2.75V, correct LDO_1P1 and LDO_2P5's
regulator range settings for i.MX6 SoCs.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per Documentation/process/license-rules.rst the SPDX notation for
header file should be /* */ style, so fix it accordingly.
Fixes: 9f30b6b1a9 ("ARM: dts: imx: Add basic dtsi file for imx6sll")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The AM3517-EVM uses a TPS65023 PMIC. This is already defined
by: compatible = "ti,tps65023"
There doesn't seem to be a need to have each regulator in the
PMIC with the 'compatible = "regulator-fixed"' since each
regulator has a min and max setting.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
i.MX6ULL has different operating ranges than i.MX6UL so add the
operating points for the i.MX6ULL and remove them from board device
trees. A 25mV offset is added to the minimum allowed values like for the
i.MX6UL.
The valid frequencies are now selected by the cpufreq driver according
to ratings stored in fuses since commit 0aa9abd4c2 ("cpufreq: imx6q:
check speed grades for i.MX6ULL")
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Mainline Commit b74c2b21e1 added the pinmux
settings for mmc1, however this pin (0x9a0) is routed to P9_42 on the cape
header. Thus any BeagleBone cape that utilizes P9_42 triggers mmc0's Write
Protect.
Fixes: b74c2b21e1 ("ARM: dts: am33xx: Add pinmux data for mmc1 in
am335x-evm, evmsk and beaglebone")
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Faiz Abbas <faiz_abbas@ti.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Jason Kridner <jkridner@beagleboard.org>
CC: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The RMI4 touchscreen driver applied inversion and axis swap in the
wrong order, violating the DT binding for those properties. This was fixed in
645a397, so correct the RDU1 DT to apply the inversion to the
correct axis.
Tested on Zii RDU1 00-5105-30 rev B
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This renames usbphy nodes 2 & 3, so that they follow the same
format as usbphy node 0 & 1 from imx53.dtsi.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add information about 3V3 power rail to avoid kernel warnings,
that dummy regulators have been added.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pinctrl_usbh1reg defines pinmux setting for reset GPIO used by
usbh1phy, but is not referenced by that node. Fix that.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The OPP properties, like "operating-points", should either be present
for all the CPUs of a cluster or none. If these are present only for a
subset of CPUs of a cluster then things will start falling apart as soon
as the CPUs are brought online in a different order. For example, this
will happen because the operating system looks for such properties in
the CPU node it is trying to bring up, so that it can create an OPP
table.
Add such missing properties.
Fix other missing property (clock latency) as well to make it all
work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The davinci-rproc driver will soon use the reset framework. Add the
resets property to the dsp node in da850.dtsi.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The psc driver registers with the reset framework as a provider. Add
the #reset-cells property to the psc0 node.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Disable the metastability workaround for USB2. The original
patch disabled the workaround on the wrong USB port.
Fixes: b8c9c6fa20 ("ARM: dts: dra7: Disable USB metastability workaround for USB2")
Cc: <stable@vger.kernel.org> [4.16+]
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On i.MX6SLL EVK board, SD3 slot can be used for
WiFi and other SD accessories, enable it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
