Allow for rate limiting Tx queues. Bitrate is set in
Mbps(megabits per second).
Mbps max-rate is set for the queue via sysfs:
/sys/class/net/<iface>/queues/tx-<queue>/tx_maxrate
ex: echo 100 >/sys/class/net/ens7/queues/tx-0/tx_maxrate
echo 200 >/sys/class/net/ens7/queues/tx-1/tx_maxrate
Note: A value of zero for tx_maxrate means disabled,
default is disabled.
Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
Co-developed-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
DCB configuration flow needs to disable and enable only the PF (main)
VSI, so use ice_ena_vsi and ice_dis_vsi. To avoid the use of ifdef to
control the staticness of these functions, move them to ice_lib.c.
Also replace the allocate and copy of old_cfg to kmemdup() in
ice_pf_dcb_cfg().
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix following compile error on i386 architecture.
ERROR: "__udivdi3" [drivers/net/ethernet/chelsio/cxgb4/cxgb4.ko] undefined!
Fixes: 0e395b3cb1 ("cxgb4: add FLOWC based QoS offload")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg says:
====================
Three small fixes:
* we hit a failure path bug related to
ieee80211_txq_setup_flows()
* also use kvmalloc() to make that less likely
* fix a timing value shortly after boot (during
INITIAL_JIFFIES)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg says:
====================
Some relatively small changes:
* typo fixes in docs
* APIs for station separation using VLAN tags rather
than separate wifi netdevs
* some preparations for upcoming features (802.3 offload
and airtime queue limits (AQL)
* stack reduction in ieee80211_assoc_success()
* use DEFINE_DEBUGFS_ATTRIBUTE in hwsim
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
From gen2 PN is totally offloaded to hardware (also the space for the
IV isn't part of the skb). As you can see in mvm/mac80211.c:3545, the
MAC for cipher types CCMP/GCMP doesn't set
IEEE80211_KEY_FLAG_PUT_IV_SPACE for gen2 NICs.
This causes all the AMSDU data to be corrupted with cipher enabled.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
match_string() returns the array index of a matching string.
Use it instead of the open-coded implementation.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add optional support for syscfg clock in dwmac-stm32.c
Now Syscfg clock is activated automatically when syscfg
registers are used
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Octeon's input ring-buffer entry has 14 bits-wide size field, so to account
for second possible VLAN header max_mtu must be further reduced.
Fixes: 109cc16526 ("ethernet/cavium: use core min/max MTU checking")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AT91 defconfig for 5.5
- Unselect PIT now that the TCBs can be used at boot time
* tag 'at91-5.5-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: configs: at91: unselect PIT
Link: https://lore.kernel.org/r/20191107222445.GA202433@piout.net
Signed-off-by: Olof Johansson <olof@lixom.net>
AT91 DT for 5.5
- New Overkiz Kizbox3 board
- Rework of the other Kizbox device trees
- New filters for i2c on sama5d4 and sama5d2
* tag 'at91-5.5-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: at91: add a dts and dtsi file for kizbox2 based boards
dt-bindings: arm: at91: Document Kizbox2-2 board binding
ARM: dts: at91: sama5d4_xplained: add digital filter for i2c
ARM: dts: at91: sama5d2_xplained: add analog and digital filter for i2c
ARM: dts: at91: add Overkiz KIZBOX3 board
dt-bindings: arm: at91: Document Kizbox3 HS board binding
dt-bindings: Add vendor prefix for Overkiz SAS
ARM: dts: at91: sama5d2: add an rtc label for derived boards
ARM: dts: at91: sama5d27_som1_ek: add mmc capabilities for SDMMC0
Link: https://lore.kernel.org/r/20191108070938.GA215379@piout.net
Signed-off-by: Olof Johansson <olof@lixom.net>
AT91 drivers for 5.5
- a new driver exposing the serial number registers through nvmem
- a few documentation and definition changes
* tag 'at91-5.5-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
soc: at91: Add Atmel SFR SN (Serial Number) support
memory: atmel-ebi: switch to SPDX license identifiers
memory: atmel-ebi: move NUM_CS definition inside EBI driver
ARM: at91: Documentation: update the sama5d3 and armv7m datasheets
Link: https://lore.kernel.org/r/20191107221644.GA201884@piout.net
Signed-off-by: Olof Johansson <olof@lixom.net>
ASPEED device tree updates for 5.5
- Lots of work on the AST2600 boards as bringup continues. There's the
eval board, and two IBM boards called Tacoma and Rainier
- A new flash layout for OpenBMC systems with larger flashes
- Better support for the MAC clocking when talking to a NCSI device,
making Linux less reliant on u-boot having done the correct thing
- LED fixes for vesin and fp5280g2
- SGPIO support
- Facebook network BMC cleanup with the common hardware moved to a
shared dtsi
* tag 'aspeed-5.5-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed: (48 commits)
ARM: dts: aspeed-g6: Add timer description
ARM: dts: aspeed: ast2600evb: Enable i2c buses
ARM: dts: aspeed-g5: Add SGPIO description
ARM: dts: aspeed: yamp: Use common dtsi
ARM: dts: aspeed: minipack: Use common dtsi
ARM: dts: aspeed: cmm: Use common dtsi
ARM: dts: aspeed: Common dtsi for Facebook AST2500 Network BMCs
ARM: dts: aspeed: rainier: gpio-keys for PSU presence
ARM: dts: aspeed: rainier: Fix i2c eeprom size
ARM: dts: tacoma: Hog LPC pinmux
ARM: dts: aspeed: rainier: Enable VUART1
ARM: dts: aspeed: rainier: Add i2c eeproms
ARM: dts: aspeed: tacoma: Use 64MB for firmware memory
ARM: dts: aspeed: tacoma: Add host FSI description
ARM: dts: ast2600evb: Enable UART workaround
ARM: dts: aspeed: tacoma: Add UART1 and workaround
ARM: dts: aspeed-g6: Add remaining UARTs
ARM: dts: aspeed-g6: Fix i2c clock source
ARM: dts: aspeed: Add RCLK to MAC clocks for RMII interfaces
ARM: dts: aspeed: tacoma: Enable FMC and SPI devices
...
Link: https://lore.kernel.org/r/CACPK8Xe8XiJ+oEp3_AXO5Mox-mXWVrOJKQLJMKJxg1WdYCTzMw@mail.gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Moritz writes:
Here is the first set of FPGA changes for 5.5
The first patch from Stephen is a trivial cleanup patch.
The following three patches add hwmon support to DFL FPGAs.
All of this patches have been reviewed and been in the last couple
of linux-next releases without issues.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
* tag 'fpga-dfl-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/mdf/linux-fpga:
fpga: dfl: fme: add power management support
fpga: dfl: fme: add thermal management support
Documentation: fpga: dfl: add descriptions for thermal/power management interfaces
fpga: Remove dev_err() usage after platform_get_irq()
Pull modules fix from Jessica Yu:
"Fix `make nsdeps` for modules composed of multiple source files.
Since $mod_source_files was not in quotes in the call to
generate_deps_for_ns(), not all the source files for a module were
being passed to spatch"
* tag 'modules-for-v5.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
scripts/nsdeps: make sure to pass all module source files to spatch
* for-next/elf-hwcap-docs:
: Update the arm64 ELF HWCAP documentation
docs/arm64: cpu-feature-registers: Rewrite bitfields that don't follow [e, s]
docs/arm64: cpu-feature-registers: Documents missing visible fields
docs/arm64: elf_hwcaps: Document HWCAP_SB
docs/arm64: elf_hwcaps: sort the HWCAP{, 2} documentation by ascending value
* for-next/smccc-conduit-cleanup:
: SMC calling convention conduit clean-up
firmware: arm_sdei: use common SMCCC_CONDUIT_*
firmware/psci: use common SMCCC_CONDUIT_*
arm: spectre-v2: use arm_smccc_1_1_get_conduit()
arm64: errata: use arm_smccc_1_1_get_conduit()
arm/arm64: smccc/psci: add arm_smccc_1_1_get_conduit()
* for-next/zone-dma:
: Reintroduction of ZONE_DMA for Raspberry Pi 4 support
arm64: mm: reserve CMA and crashkernel in ZONE_DMA32
dma/direct: turn ARCH_ZONE_DMA_BITS into a variable
arm64: Make arm64_dma32_phys_limit static
arm64: mm: Fix unused variable warning in zone_sizes_init
mm: refresh ZONE_DMA and ZONE_DMA32 comments in 'enum zone_type'
arm64: use both ZONE_DMA and ZONE_DMA32
arm64: rename variables used to calculate ZONE_DMA32's size
arm64: mm: use arm64_dma_phys_limit instead of calling max_zone_dma_phys()
* for-next/relax-icc_pmr_el1-sync:
: Relax ICC_PMR_EL1 (GICv3) accesses when ICC_CTLR_EL1.PMHE is clear
arm64: Document ICC_CTLR_EL3.PMHE setting requirements
arm64: Relax ICC_PMR_EL1 accesses when ICC_CTLR_EL1.PMHE is clear
* for-next/double-page-fault:
: Avoid a double page fault in __copy_from_user_inatomic() if hw does not support auto Access Flag
mm: fix double page fault on arm64 if PTE_AF is cleared
x86/mm: implement arch_faults_on_old_pte() stub on x86
arm64: mm: implement arch_faults_on_old_pte() on arm64
arm64: cpufeature: introduce helper cpu_has_hw_af()
* for-next/misc:
: Various fixes and clean-ups
arm64: kpti: Add NVIDIA's Carmel core to the KPTI whitelist
arm64: mm: Remove MAX_USER_VA_BITS definition
arm64: mm: simplify the page end calculation in __create_pgd_mapping()
arm64: print additional fault message when executing non-exec memory
arm64: psci: Reduce the waiting time for cpu_psci_cpu_kill()
arm64: pgtable: Correct typo in comment
arm64: docs: cpu-feature-registers: Document ID_AA64PFR1_EL1
arm64: cpufeature: Fix typos in comment
arm64/mm: Poison initmem while freeing with free_reserved_area()
arm64: use generic free_initrd_mem()
arm64: simplify syscall wrapper ifdeffery
* for-next/kselftest-arm64-signal:
: arm64-specific kselftest support with signal-related test-cases
kselftest: arm64: fake_sigreturn_misaligned_sp
kselftest: arm64: fake_sigreturn_bad_size
kselftest: arm64: fake_sigreturn_duplicated_fpsimd
kselftest: arm64: fake_sigreturn_missing_fpsimd
kselftest: arm64: fake_sigreturn_bad_size_for_magic0
kselftest: arm64: fake_sigreturn_bad_magic
kselftest: arm64: add helper get_current_context
kselftest: arm64: extend test_init functionalities
kselftest: arm64: mangle_pstate_invalid_mode_el[123][ht]
kselftest: arm64: mangle_pstate_invalid_daif_bits
kselftest: arm64: mangle_pstate_invalid_compat_toggle and common utils
kselftest: arm64: extend toplevel skeleton Makefile
* for-next/kaslr-diagnostics:
: Provide diagnostics on boot for KASLR
arm64: kaslr: Check command line before looking for a seed
arm64: kaslr: Announce KASLR status on boot
The Zynq QSPI controller features 2 CS. When the num-cs DT property
is set to 2, the hardware will be initialized to support having two
devices connected over each CS.
In this case, both CS lines are driven by the state of the U_PAGE
(upper page) bit. When unset, the lower page (CS0) is selected,
otherwise it is the upper page (CS1).
Change tested on a custom design featuring two SPI-NORs with different
CS on the Zynq-7000 QSPI bus.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-8-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Supporting more than one CS will need some tweaking of the linear
configuration register which is (rightfully) initialized in the
hardware initialization helper. The extra initialization needs the
knowledge of the actual number of CS, which is retrieved by reading
the value of the num-cs DT property.
As the initialization helper is called pretty early and might be
called much later in the probe without side effect, let's delay it a
bit so that the number of CS will be available when running this
helper. This way, adding support for multiple CS lines in a next patch
will be eased.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-7-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The code used to assert and de-assert a chip select line is very
complicated for no reason. Simplify the logic by either setting or
resetting the concerned bit, which actually only changes an electrical
state.
Update the comment to reflect that there is no possibility to actually
choose a CS as the default (CS0) will be driven in any case.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-6-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull arm64 fix from Will Deacon:
"Fix pte_same() to avoid getting stuck on write fault.
This single arm64 fix is a revert of 747a70e60b ("arm64: Fix
copy-on-write referencing in HugeTLB"), not because that patch was
wrong, but because it was broken by aa57157be6 ("arm64: Ensure
VM_WRITE|VM_SHARED ptes are clean by default") which we merged in
-rc6.
We spotted the issue in Android (AOSP), where one of the JIT threads
gets stuck on a write fault during boot because the faulting pte is
marked as PTE_DIRTY | PTE_WRITE | PTE_RDONLY and the fault handler
decides that there's nothing to do thanks to pte_same() masking out
PTE_RDONLY.
Thanks to John Stultz for reporting this and testing this so quickly,
and to Steve Capper for confirming that the HugeTLB tests continue to
pass"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Do not mask out PTE_RDONLY in pte_same()
The owner member of struct pwm_ops must be set to THIS_MODULE to
increase the reference count of the module such that the module cannot
be removed while its code is in use.
Fixes: daa5abc41c ("pwm: Add support for Broadcom iProc PWM controller")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Now that we print diagnostics at boot the reason why we do not initialise
KASLR matters. Currently we check for a seed before we check if the user
has explicitly disabled KASLR on the command line which will result in
misleading diagnostics so reverse the order of those checks. We still
parse the seed from the DT early so that if the user has both provided a
seed and disabled KASLR on the command line we still mask the seed on
the command line.
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Currently the KASLR code is silent at boot unless it forces on KPTI in
which case a message will be printed for that. This can lead to users
incorrectly believing their system has the feature enabled when it in
fact does not, and if they notice the problem the lack of any
diagnostics makes it harder to understand the problem. Add an initcall
which prints a message showing the status of KASLR during boot to make
the status clear.
This is particularly useful in cases where we don't have a seed. It
seems to be a relatively common error for system integrators and
administrators to enable KASLR in their configuration but not provide
the seed at runtime, often due to seed provisioning breaking at some
later point after it is initially enabled and verified.
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The declarations were introduced with the file, but the declared
variables were not used.
Fixes: 65294c1f2c ("nfsd: add a new struct file caching facility to nfsd")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
The callback code relies on the fact that much of it is only ever called
from the ordered workqueue callback_wq, and this is worth documenting.
Reported-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
When we're destroying the client lease, and we call
nfsd4_shutdown_callback(), we must ensure that we do not return
before all outstanding callbacks have terminated and have
released their payloads.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Move all the cb_holds_slot management into helper functions. No change
in behavior.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
This is to improve the performance in the compute mode
for vega10. For example, the original performance for a rocm
bandwidth test: 2G internal GPU copy, is about 99GB/s.
With the idle power features disabled dynamically, the porformance
is promoted to about 215GB/s.
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It will cause modprobe atombios stuck problem in raven2 if it doesn't
allow direct upload save restore list from gfx driver.
So it needs to allow direct upload save restore list for raven2
temporarily.
Signed-off-by: changzhu <Changfeng.Zhu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Create a new function called lookup_rec() from the functionality of
ftrace_location_range(). The difference between lookup_rec() is that it
returns the record that it finds, where as ftrace_location_range() returns
only if it found a match or not.
The lookup_rec() is static, and can be used for new functionality where
ftrace needs to find a record of a specific address.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Most of the functionality of __ftrace_hash_move() can be reused, but not all
of it. That is, __ftrace_hash_move() is used to simply make a new hash from
an existing one, using the same size as the original. Creating a dup_hash(),
where we can specify a new size will be useful when we want to create a hash
with a default size, or simply copy the old one.
Signed-off-by: Steven Rostedt (VMWare) <rostedt@goodmis.org>
Pull XArray fixes from Matthew Wilcox:
"These all fix various bugs, some of which people have tripped over and
some of which have been caught by automatic tools"
* tag 'xarray-5.4' of git://git.infradead.org/users/willy/linux-dax:
idr: Fix idr_alloc_u32 on 32-bit systems
idr: Fix integer overflow in idr_for_each_entry
radix tree: Remove radix_tree_iter_find
idr: Fix idr_get_next_ul race with idr_remove
XArray: Fix xas_next() with a single entry at 0
There are a few manually-calculated variable-length struct allocations
left, this converts them to use struct_size. Found with the following
git grep command
git grep -A1 'kzalloc.*sizeof[^_].*+'
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lkml.kernel.org/r/20190927185110.29897-1-steve@sk2.org
Acked-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
[sboyd@kernel.org: Add grep command]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Pull power management fix from Rafael Wysocki:
"Fix an 'unchecked MSR access' warning in the intel_pstate cpufreq
driver (Srinivas Pandruvada)"
* tag 'pm-5.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: intel_pstate: Fix invalid EPB setting
Pull sound fixes from Takashi Iwai:
"It became a bit largish, but all small and good for 5.4:
- A regression fix of ALSA timer code bug that sneaked in by a recent
cleanup; never trust innocent-looking guys...
- Fix for compress API max size check signedness
- Fixes in HD-audio: CA0132 work stall, Intel Tigerlake HDMI
- A few fixes for SOF: memory leak, sanity-check and build fixes
- A collection of device-specific fixes: firewire, rockchip, ASoC
HDMI, rsnd, ASoC HDA, stm32, TI, kirkwood, msm, max98373"
* tag 'sound-5.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: timer: Fix incorrectly assigned timer instance
ASoC: SOF: topology: Fix bytes control size checks
ALSA: hda: hdmi - add Tigerlake support
ASoC: max98373: replace gpio_request with devm_gpio_request
ASoC: stm32: sai: add restriction on mmap support
ALSA: hda/ca0132 - Fix possible workqueue stall
ASoC: hdac_hda: fix race in device removal
ALSA: bebob: fix to detect configured source of sampling clock for Focusrite Saffire Pro i/o series
ASoC: rockchip: rockchip_max98090: Enable SHDN to fix headset detection
ASoC: ti: sdma-pcm: Add back the flags parameter for non standard dma names
ASoC: SOF: ipc: Fix memory leak in sof_set_get_large_ctrl_data
ASoC: SOF: Fix memory leak in sof_dfsentry_write
ASoC: SOF: Intel: hda-stream: fix the CONFIG_ prefix missing
ASoC: kirkwood: fix device remove ordering
ASoC: rsnd: dma: fix SSI9 4/5/6/7 busif dma address
ASoC: hdmi-codec: drop mutex locking again
ASoC: kirkwood: fix external clock probe defer
ASoC: compress: fix unsigned integer overflow check
ASoC: msm8916-wcd-analog: Fix RX1 selection in RDAC2 MUX
Pull drm fixes from Dave Airlie:
"Weekly fixes for drm: amdgpu has a few but they are pretty scattered
fixes, the fbdev one is a build regression fix that we didn't want to
risk leaving out, otherwise a couple of i915, one radeon and a core
atomic fix.
core:
- add missing documentation for GEM shmem madvise helpers
- Fix for a state dereference in atomic self-refresh helpers
fbdev:
- One compilation fix for c2p fbdev helpers
amdgpu:
- Fix navi14 display issue root cause and revert workaround
- GPU reset scheduler interaction fix
- Fix fan boost on multi-GPU
- Gfx10 and sdma5 fixes for navi
- GFXOFF fix for renoir
- Add navi14 PCI ID
- GPUVM fix for arcturus
radeon:
- Port an SI power fix from amdgpu
i915:
- Fix HPD poll to avoid kworker consuming a lot of cpu cycles.
- Do not use TBT type for non Type-C ports"
* tag 'drm-fixes-2019-11-08' of git://anongit.freedesktop.org/drm/drm:
drm/radeon: fix si_enable_smc_cac() failed issue
drm/amdgpu/renoir: move gfxoff handling into gfx9 module
drm/amdgpu: add warning for GRBM 1-cycle delay issue in gfx9
drm/amdgpu: add dummy read by engines for some GCVM status registers in gfx10
drm/amdgpu: register gpu instance before fan boost feature enablment
drm/amd/swSMU: fix smu workload bit map error
drm/shmem: Add docbook comments for drm_gem_shmem_object madvise fields
drm/amdgpu: add navi14 PCI ID
Revert "drm/amd/display: setting the DIG_MODE to the correct value."
drm/amd/display: Add ENGINE_ID_DIGD condition check for Navi14
drm/amdgpu: dont schedule jobs while in reset
drm/amdgpu/arcturus: properly set BANK_SELECT and FRAGMENT_SIZE
drm/atomic: fix self-refresh helpers crtc state dereference
drm/i915/dp: Do not switch aux to TBT mode for non-TC ports
drm/i915: Avoid HPD poll detect triggering a new detect cycle
fbdev: c2p: Fix link failure on non-inlining
Pull clk fixes from Stephen Boyd:
"Fixes for various clk driver issues that happened because of code we
merged this merge window.
The Amlogic driver was missing some flags causing rates to be rounded
improperly or clk_set_rate() to fail. The Samsung driver wasn't
freeing everything on error paths and improperly saving/restoring PLL
state across suspend/resume. The at91 driver was calling msleep() too
early when scheduling hadn't started, so we put in place a quick
solution until we can handle this sort of problem in the core
framework.
There were also problems with the Allwinner driver and operator
precedence being incorrect causing subtle bugs. Finally, the TI driver
was duplicating aliases and not delaying long enough leading to some
unexpected timeouts"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: ti: clkctrl: Fix failed to enable error with double udelay timeout
clk: ti: dra7-atl-clock: Remove ti_clk_add_alias call
clk: sunxi-ng: a80: fix the zero'ing of bits 16 and 18
clk: sunxi: Fix operator precedence in sunxi_divs_clk_setup
clk: ast2600: Fix enabling of clocks
clk: at91: avoid sleeping early
clk: imx8m: Use SYS_PLL1_800M as intermediate parent of CLK_ARM
clk: samsung: exynos5420: Preserve PLL configuration during suspend/resume
clk: samsung: exynos542x: Move G3D subsystem clocks to its sub-CMU
clk: samsung: exynos5433: Fix error paths
clk: at91: sam9x60: fix programmable clock
clk: meson: g12a: set CLK_MUX_ROUND_CLOSEST on the cpu clock muxes
clk: meson: g12a: fix cpu clock rate setting
clk: meson: gxbb: let sar_adc_clk_div set the parent clock rate
