Add a simple fake_sigreturn testcase which places a valid sigframe on a
non-16 bytes aligned SP. Expects a SIGSEGV on test PASS.
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add a simple fake_sigreturn testcase which builds a ucontext_t with a
badly sized header that causes a overrun in the __reserved area and
place it onto the stack. Expects a SIGSEGV on test PASS.
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add a simple fake_sigreturn testcase which builds a ucontext_t with
an anomalous additional fpsimd_context and place it onto the stack.
Expects a SIGSEGV on test PASS.
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add a simple fake_sigreturn testcase which builds a ucontext_t without
the required fpsimd_context and place it onto the stack.
Expects a SIGSEGV on test PASS.
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add a simple fake_sigreturn testcase which builds a ucontext_t with a
badly sized terminator record and place it onto the stack.
Expects a SIGSEGV on test PASS.
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add a simple fake_sigreturn testcase which builds a ucontext_t with a bad
magic header and place it onto the stack. Expects a SIGSEGV on test PASS.
Introduce a common utility assembly trampoline function to invoke a
sigreturn while placing the provided sigframe at wanted alignment and
also an helper to make space when needed inside the sigframe reserved
area.
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Introduce a new common utility function get_current_context() which can be
used to grab a ucontext without the help of libc, and also to detect if
such ucontext has been successfully used by placing it on the stack as a
fake sigframe.
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Extend signal testing framework to allow the definition of a custom per
test initialization function to be run at the end of the common test_init
after test setup phase has completed and before test-run routine.
This custom per-test initialization function also enables the test writer
to decide on its own when forcibly skip the test itself using standard KSFT
mechanism.
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add 6 simple mangle testcases that mess with the ucontext_t from within
the signal handler, trying to toggle PSTATE mode bits to trick the system
into switching to EL1/EL2/EL3 using both SP_EL0(t) and SP_ELx(h).
Expects SIGSEGV on test PASS.
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add a simple mangle testcase which messes with the ucontext_t from within
the signal handler, trying to set PSTATE DAIF bits to an invalid value
(masking everything). Expects SIGSEGV on test PASS.
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add some arm64/signal specific boilerplate and utility code to help
further testcases' development.
Introduce also one simple testcase mangle_pstate_invalid_compat_toggle
and some related helpers: it is a simple mangle testcase which messes
with the ucontext_t from within the signal handler, trying to toggle
PSTATE state bits to switch the system between 32bit/64bit execution
state. Expects SIGSEGV on test PASS.
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Modify KSFT arm64 toplevel Makefile to maintain arm64 kselftests organized
by subsystem, keeping them into distinct subdirectories under arm64 custom
KSFT directory: tools/testing/selftests/arm64/
Add to such toplevel Makefile a mechanism to guess the effective location
of Kernel headers as installed by KSFT framework.
Fit existing arm64 tags kselftest into this new schema moving them into
their own subdirectory (arm64/tags).
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
- Support for additional PMU topologies on HiSilicon platforms
- Support for CCN-512 interconnect PMU
- Support for AXI ID filtering in the IMX8 DDR PMU
- Support for the CCPI2 uncore PMU in ThunderX2
- Driver cleanup to use devm_platform_ioremap_resource()
* for-next/perf:
drivers/perf: hisi: update the sccl_id/ccl_id for certain HiSilicon platform
perf/imx_ddr: Dump AXI ID filter info to userspace
docs/perf: Add AXI ID filter capabilities information
perf/imx_ddr: Add driver for DDR PMU in i.MX8MPlus
perf/imx_ddr: Add enhanced AXI ID filter support
bindings: perf: imx-ddr: Add new compatible string
docs/perf: Add explanation for DDR_CAP_AXI_ID_FILTER_ENHANCED quirk
arm64: perf: Simplify the ARMv8 PMUv3 event attributes
drivers/perf: Add CCPI2 PMU support in ThunderX2 UNCORE driver.
Documentation: perf: Update documentation for ThunderX2 PMU uncore driver
Documentation: Add documentation for CCN-512 DTS binding
perf: arm-ccn: Enable stats for CCN-512 interconnect
perf/smmuv3: use devm_platform_ioremap_resource() to simplify code
perf/arm-cci: use devm_platform_ioremap_resource() to simplify code
perf/arm-ccn: use devm_platform_ioremap_resource() to simplify code
perf: xgene: use devm_platform_ioremap_resource() to simplify code
perf: hisi: use devm_platform_ioremap_resource() to simplify code
Add NULL checks to show() and store() in cpufreq.c to avoid attempts
to invoke a NULL callback.
Though some interfaces of cpufreq are set as read-only, users can
still get write permission using chmod which can lead to a kernel
crash, as follows:
chmod +w /sys/devices/system/cpu/cpu0/cpufreq/scaling_cur_freq
echo 1 > /sys/devices/system/cpu/cpu0/cpufreq/scaling_cur_freq
This bug was found in linux 4.19.
Signed-off-by: Kai Shen <shenkai8@huawei.com>
Reported-by: Feilong Lin <linfeilong@huawei.com>
Reviewed-by: Feilong Lin <linfeilong@huawei.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[ rjw: Subject & changelog ]
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The max value of EPB can only be 0x0F. Attempting to set more than that
triggers an "unchecked MSR access error" warning which happens in
intel_pstate_hwp_force_min_perf() called via cpufreq stop_cpu().
However, it is not even necessary to touch the EPB from intel_pstate,
because it is restored on every CPU online by the intel_epb.c code,
so let that code do the right thing and drop the redundant (and
incorrect) EPB update from intel_pstate.
Fixes: af3b7379e2 ("cpufreq: intel_pstate: Force HWP min perf before offline")
Reported-by: Qian Cai <cai@lca.pw>
Cc: 5.2+ <stable@vger.kernel.org> # 5.2+
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The data byte order selection registers in the APB2OPB primarily expose some
internal plumbing necessary to get correct write accesses onto the OPB.
OPB write cycles require "data mirroring" across the 32-bit data bus to
support variable data width slaves that don't implement "byte enables".
For slaves that do implement byte enables the master can signal which
bytes on the data bus the slave should consider valid.
The data mirroring behaviour is specified by the following table:
+-----------------+----------+-----------------------------------+
| | | 32-bit Data Bus |
+---------+-------+----------+---------+---------+-------+-------+
| | | | | | | |
| ABus | Mn_BE | Request | Dbus | Dbus | Dbus | Dbus |
| (30:31) | (0:3) | Transfer | 0:7 | 8:15 | 16:23 | 24:31 |
| | | Size | byte0 | byte1 | byte2 | byte3 |
+---------+-------+----------+---------+---------+-------+-------+
| 00 | 1111 | fullword | byte0 | byte1 | byte2 | byte3 |
+---------+-------+----------+---------+---------+-------+-------+
| 00 | 1110 | halfword | byte0 | byte1 | byte2 | |
+---------+-------+----------+---------+---------+-------+-------+
| 01 | 0111 | byte | _byte1_ | byte1 | byte2 | byte3 |
+---------+-------+----------+---------+---------+-------+-------+
| 00 | 1100 | halfword | byte0 | byte1 | | |
+---------+-------+----------+---------+---------+-------+-------+
| 01 | 0110 | byte | _byte1_ | byte1 | byte2 | |
+---------+-------+----------+---------+---------+-------+-------+
| 10 | 0011 | halfword | _byte2_ | _byte3_ | byte2 | byte3 |
+---------+-------+----------+---------+---------+-------+-------+
| 00 | 1000 | byte | byte0 | | | |
+---------+-------+----------+---------+---------+-------+-------+
| 01 | 0100 | byte | _byte1_ | byte1 | | |
+---------+-------+----------+---------+---------+-------+-------+
| 10 | 0010 | byte | _byte2_ | | byte2 | |
+---------+-------+----------+---------+---------+-------+-------+
| 11 | 0001 | byte | _byte3_ | _byte3_ | | byte3 |
+---------+-------+----------+---------+---------+-------+-------+
Mirrored data values are highlighted by underscores in the Dbus columns.
The values in the ABus and Request Transfer Size columns correspond to
values in the field names listed in the write data order select register
descriptions.
Similar configuration registers are exposed for reads which enables the
secondary purpose of configuring hardware endian conversions. It appears the
data bus byte order is switched around in hardware so set the registers such
that we can access the correct values for all widths. The values were
determined by experimentation on hardware against fixed CFAM register
values to configure the read data order, then in combination with the
table above and the register layout documentation in the AST2600
datasheet performing write/read cycles to configure the write data order
registers.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Alistair Popple <alistair@popple.id.au>
Link: https://lore.kernel.org/r/20191108051945.7109-12-joel@jms.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ast2600 BMC has a pair of FSI masters in it, behind an AHB to OPB
bridge.
The master driver supports reads and writes of full words, half word and
byte accesses to remote CFAMs. It can perform very basic error recovery
through resetting of the FSI port when an error is detected, and the
issuing of breaks and terms.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Alistair Popple <alistair@popple.id.au>
--
v2:
- remove debugging
- squash in fixes
Link: https://lore.kernel.org/r/20191108051945.7109-10-joel@jms.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Subtracting the offset delta from four-byte alignment lead to wrapping
of the requested length where `count` is less than `off`. Generalise the
length handling to enable and optimise aligned access sizes for all
offset and size combinations. The new formula produces the following
results for given offset and count values:
offset count | length
--------------+-------
0 1 | 1
0 2 | 2
0 3 | 2
0 4 | 4
0 5 | 4
1 1 | 1
1 2 | 1
1 3 | 1
1 4 | 1
1 5 | 1
2 1 | 1
2 2 | 2
2 3 | 2
2 4 | 2
2 5 | 2
3 1 | 1
3 2 | 1
3 3 | 1
3 4 | 1
3 5 | 1
We might need something like this for the cfam chardevs as well, for
example we don't currently implement any alignment restrictions /
handling in the hardware master driver.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20191108051945.7109-6-joel@jms.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The paths added back in 4.13 weren't quite correct. The in reality the
files documented lived under
/sys/devices/../fsi0/rescan
/sys/devices/../fsi0/break
/sys/devices/../fsi0/slave@00:00/term
/sys/devices/../fsi0/slave@00:00/raw
In 5.5 with the addition of the FSI class they move to
/sys/devices/../fsi-master/fsi0/rescan
/sys/devices/../fsi-master/fsi0/break
/sys/devices/../fsi-master/fsi0/slave@00:00/term
/sys/devices/../fsi-master/fsi0/slave@00:00/raw
This is closer to how the (incorrect) documentation described them.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Alistair Popple <alistair@popple.id.au>
Link: https://lore.kernel.org/r/20191108051945.7109-4-joel@jms.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This provides an alternative mechanism for AP VLAN support where a
single netdev is used with VLAN tagged frames instead of separate
netdevs for each VLAN without tagged frames from the WLAN driver.
By setting NL80211_EXT_FEATURE_VLAN_OFFLOAD flag the driver indicates
support for a single netdev with VLAN tagged frames. Separate
VLAN-specific netdevs can be added using RTM_NEWLINK/IFLA_VLAN_ID
similarly to Ethernet. NL80211_CMD_NEW_KEY (for group keys),
NL80211_CMD_NEW_STATION, and NL80211_CMD_SET_STATION will optionally
specify vlan_id using NL80211_ATTR_VLAN_ID.
Signed-off-by: Gurumoorthi Gnanasambandhan <gguru@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20191031214640.5012-1-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add USB0 as otg port and USB1 as host port.
Although USB0 can be used at super-speed, limit the
speed to high-speed for now till SERDES PHY support
is added.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
J721e has 2 USB super-speed controllers add them.
The USB2 PHY doesn't need any configuration.
USB3 PHY needs to be implemented using the Cadence
Sierra PHY. This support will be added later.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
To implement airtime queue limiting, we need to keep a running account of
the estimated airtime of all skbs queued into the device. Do to this
correctly, we need to store the airtime estimate into the skb so we can
decrease the outstanding balance when the skb is freed. This means that the
time estimate must be stored somewhere that will survive for the lifetime
of the skb.
To get this, decrease the size of the ack_frame_id field to 6 bits, and
lower the size of the ID space accordingly. This leaves 10 bits for use for
tx_time_est, which is enough to store a maximum of 4096 us, if we shift the
values so they become units of 4us.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/157182474063.150713.16132669599100802716.stgit@toke.dk
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Downloading ath10k firmware needs a large number of IOs and
cpuidle's miss predictions make it worse. In the worst case,
resume time can be three times longer than the average on sdio.
This patch disables cpuidle during firmware downloading by
applying PM_QOS_CPU_DMA_LATENCY in ath10k_download_fw().
Tested-on: QCA9880
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00029
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
STA number was not restored if OOM happened.
Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00018
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k does not provide transmit rate info per MSDU
in tx completion, mark that as -1 so mac80211
will ignore the rates. This fixes mac80211 update Mesh
link metric with invalid transmit rate info.
Tested HW: QCA9984
Tested FW: 10.4-3.9.0.2-00035
Signed-off-by: Hou Bao Hou <houbao@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the first 5 minutes after boot (time of INITIAL_JIFFIES),
ieee80211_sta_last_active() returns zero if last_ack is zero. This
leads to "inactive time" showing jiffies_to_msecs(jiffies).
# iw wlan0 station get fc:ec:da:64:a6:dd
Station fc:ec:da:64:a6:dd (on wlan0)
inactive time: 4294894049 ms
.
.
connected time: 70 seconds
Fix by returning last_rx if last_ack == 0.
Signed-off-by: Ahmed Zaki <anzaki@gmail.com>
Link: https://lore.kernel.org/r/20191031121243.27694-1-anzaki@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The FQ implementation used by mac80211 allocates memory using kmalloc(),
which can fail; and Johannes reported that this actually happens in
practice.
To avoid this, switch the allocation to kvmalloc() instead; this also
brings fq_impl in line with all the FQ qdiscs.
Fixes: 557fc4a098 ("fq: add fair queuing framework")
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191105155750.547379-1-toke@redhat.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This pointer is used to point to data that is constant. Thanks to this
we can avoid a lot of casting and we make more clear when the data is
constant or variable.
Suggested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Ricardo Ribalda Delgado <ribalda@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This allows setting the default value on compound controls created via
v4l2_ctrl_new_custom.
Signed-off-by: Ricardo Ribalda Delgado <ribalda@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When driver is built as module and probe during insmod is deferred
because of sensor subdevs, there is NULL pointer deference because
mdev is cleaned up and then access it from v4l2_device_unregister().
Fix the wrong mdev and v4l2 dev order in error path of probe.
This fixes below null pointer deference:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = ca026f68
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
[...]
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
PC is at ida_free+0x7c/0x160
LR is at xas_start+0x44/0x204
[...]
[<c0dafd60>] (ida_free) from [<c083c20c>] (__media_device_unregister_entity+0x18/0xc0)
[<c083c20c>] (__media_device_unregister_entity) from [<c083c2e0>] (media_device_unregister_entity+0x2c/0x38)
[<c083c2e0>] (media_device_unregister_entity) from [<c0843404>] (v4l2_device_release+0xd0/0x104)
[<c0843404>] (v4l2_device_release) from [<c0632558>] (device_release+0x28/0x98)
[<c0632558>] (device_release) from [<c0db1204>] (kobject_put+0xa4/0x208)
[<c0db1204>] (kct_put) from [<bf00bac4>] (fimc_capture_subdev_unregistered+0x58/0x6c [s5p_fimc])
[<bf00bac4>] (fimc_capture_subdev_unregistered [s5p_fimc]) from [<c084a1cc>] (v4l2_device_unregister_subdev+0x6c/0xa8)
[<c084a1cc>] (v4l2_device_unregister_subdev) from [<c084a350>] (v4l2_device_unregister+0x64/0x94)
[<c084a350>] (v4l2_device_unregister) from [<bf0101ac>] (fimc_md_probe+0x4ec/0xaf8 [s5p_fimc])
[...]
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Fixes: 9832e155f1 ("[media] media-device: split media initialization and registration")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
