A clean-up device-tree patch to ensure pinmux entry reuse.
* tag 'davinci-for-v4.12/dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850: move spi0_cs3_pin pinconf node
Signed-off-by: Olof Johansson <olof@lixom.net>
STM32 DT updates for v4.12, round 1
Highlights:
----------
- ADD RTC support on STM32F746 MCU
- Enable RTC on STM32F746 Eval board
- Enable clocks on STM32F746 MCU
- Enable DMA, pwm1 and pwm3 on STM32F429I Eval
- Add support of STM32H743 MCU and his Eval board
- Enable USB HS and FS on STM32F469 Disco board
* tag 'stm32-dt-for-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
dt-bindings: Document the STM32 USB OTG DWC2 core binding
ARM: dts: stm32: Enable USB HS in FS mode (embedded phy) on stm32f429-disco
ARM: dts: stm32: Enable USB FS on stm32f469-disco
ARM: dts: stm32: Add USB FS support for STM32F429 MCU
ARM: dts: stm32: Add STM32H743 MCU and STM32H743i-EVAL board
ARM: dts: stm32: Enable pwm1 and pwm3 on stm32f429i-eval
ARM: dts: stm32: Enable dma by default on stm32f4 adc
ARM: dts: stm32: enable RTC on stm32746g-eval
ARM: dts: stm32: Add RTC support for STM32F746 MCU
ARM: dts: stm32: set HSE_RTC clock frequency to 1 MHz on stm32f746
dt-bindings: mfd: Add STM32F7 RCC numeric constants into DT include file
ARM: dts: stm32: Enable clocks for STM32F746 MCU
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch fixes the following set of warnings on vexpress platforms:
sysreg@010000 simple-bus unit address format error, expected "10000"
sysctl@020000 simple-bus unit address format error, expected "20000"
i2c@030000 simple-bus unit address format error, expected "30000"
aaci@040000 simple-bus unit address format error, expected "40000"
mmci@050000 simple-bus unit address format error, expected "50000"
kmi@060000 simple-bus unit address format error, expected "60000"
kmi@070000 simple-bus unit address format error, expected "70000"
uart@090000 simple-bus unit address format error, expected "90000"
uart@0a0000 simple-bus unit address format error, expected "a0000"
uart@0b0000 simple-bus unit address format error, expected "b0000"
uart@0c0000 simple-bus unit address format error, expected "c0000"
wdt@0f0000 simple-bus unit address format error, expected "f0000"
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Pull ARM SoC fixes from Olof Johansson:
"Again, a batch that's been sitting a couple of weeks, mostly because
I anticipated a bit more material but it didn't show up -- which is
good.
These are all your garden variety fixes for ARM platforms.
The most visible issue fixed here is probably the SMP reset issue on
OMAP, the rest are minor stuff"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: allwinner: a64: add pmu0 regs for USB PHY
ARM: OMAP2+: omap_device: Sync omap_device and pm_runtime after probe defer
reset: add exported __reset_control_get, return NULL if optional
ARM: orion5x: only call into phylib when available
ARM: omap2+: Revert omap-smp.c changes resetting CPU1 during boot
ARM: dts: am335x-evmsk: adjust mmc2 param to allow suspend
ARM: dts: ti: fix PCI bus dtc warnings
ARM: dts: am335x-baltos: disable EEE for Atheros 8035 PHY
ARM: dts: OMAP3: Fix MFG ID EEPROM
ARM: sun8i: a33: add operating-points-v2 property to all nodes
ARM: sun8i: a33: remove highest OPP to fix CPU crashes
Regression fix for omap interconnect code for deferred probe.
Without this fix we can get PM related warnings for devices that
use deferred probe. If necessary, this fix can wait for the
v4.12 merge window no problem.
* tag 'omap-for-v4.11/fixes-rc6-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: omap_device: Sync omap_device and pm_runtime after probe defer
ARM: omap2+: Revert omap-smp.c changes resetting CPU1 during boot
ARM: dts: am335x-evmsk: adjust mmc2 param to allow suspend
ARM: dts: ti: fix PCI bus dtc warnings
ARM: dts: am335x-baltos: disable EEE for Atheros 8035 PHY
ARM: dts: OMAP3: Fix MFG ID EEPROM
Signed-off-by: Olof Johansson <olof@lixom.net>
The envelope detector can analyze 6 different signals, selectable with a
mux controlled by three gpio pins.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
We found out that HW checksum generation only works from AST2500
onward. This disables it on AST2400 and removes the "no-hw-checksum"
properties in the device-trees. The problem we had wasn't related
to NC-SI.
Also rework the logic testing for that property so it can be used
to disable HW checksum generation and checking regardless of whether
NC-SI is used or not in case other variants out there need this.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We test for aspeed chips to handle a couple of special cases,
but we do that by checking the machine type which isn't right.
Instead check the actual device compatible property. This also
updates the dtsi files for the aspeed SoC to match.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently most nodes got labels to make them referenceable. The USB 3.0
nodes as well as the nodes for the SATA controllers were left out,
rectify the omission.
The labels "sataX" are already used by some boards for the SATA ports,
therefore use "ahciX" to label the SATA controller nodes.
To avoid potential confusion by labeling an USB3.0 controller "usb2" use
usb3_X as labels. This also coincides with the node names themselves
(usb@xxxxx vs usb3@xxxxx).
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The hpd pin of the second hdmi connector of the Utilite Pro is wired
up to a gpio pin of the SoC. Reflect this in the device tree.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On imx6qp-sabresd LDO_ARM is connected to a different PMIC output than
the other imx6qdl-sabresd boards.
Setting cpu0 arm-supply to sw2_reg is wrong, this must have mistakenly
slipped out of the vendor tree where this is are used for LDO bypass.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Setting the supply is optional but beneficial, it will cause PMIC
voltages to be dynamically changed with cpu frequency.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX25 contains two AHB to IP bridges (AIPS), each of which has a set of
control registers. Add the memory regions for the control registers to
the Device Tree.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Model the Carrier Board power distribution by adding a fixed 3.3V
and 5V regulator. The 3.3V regulator is connected to the backlight
as well as the display supply. The 5V regulator is used to supply
USB VBUS.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The ADC is directly supplied by the PMIC 1.8V rail, remove the
superfluous fixed regulator.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The regulator-always-on property on the Ethernet rail prevents Linux
from disabling the rail when Ethernet is shut down (suspend or simply
link down). With this change the regulator framework will disable the
rail when the Ethernet PHY is not used, saving power especially on
carrier board not using Ethernet.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix wrong voltage of PWR_EN_+V3.3 rail. The error had no noticeable
effect since no consumer explicitly requested a specific voltage.
Also use round voltages as it is common in other device trees.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
To make use of the new eLCDIF DRM driver OF graph description is
required. Describe the display using OF graph nodes.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Rename the switch2@0 label of the switch2 node to switch@0 to respect
the general unit@address DTS rule, and be consistent with the other
switch nodes of the DTS file.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
lcdif nodes are differ wrt specific LCD connected on Is.IoT MX6UL
module, so create separate file 'imx6ul-isiot-common.dtsi' for common
lcdif node structure and include the same on respective dts.
More common nodes will add in future patches.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds support for the Zodiac Inflight Innovations RDU2 board,
which has both a Quad and a QuadPlus variant.
The board supports different panels, with the bootloader patching
in the correct compatible, depending on the hardware configuration.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the DT nodes for the Prefetch Resolve Gaskets found on i.MX6QP
and hook them up to the assigned IPU nodes.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the DT nodes for the Prefetch Resolve Engines found on i.MX6QP.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The pinfunc definitions are ordered by mux_reg and so automatically by
conf_reg, too. PAD_TDO is the only pad that has a conf_reg but no
mux_reg. Put it to the place where it its in the order of conf_regs
instead of the top.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.CoreM6 Quad/Dual OpenFrame modules are "system on modules plus
openframe display carriers" which are good solution for develop
user friendly graphic user interface.
General features:
CPU NXP i.MX6Q rev1.2 at 792 MHz
RAM 1GB, 32, 64 bit, DDR3-800/1066
NAND SLC,512MB
LVDS Display TFT 12.3" industrial, 1280x480 resolution
Backlight LED backlight, brightness 350 Cd/m2
Power supply 15 to 30 Vdc
Cc: Domenico Acri <domenico.acri@engicam.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.CoreM6 Quad/Dual OpenFrame modules are "system on modules plus
openframe display carriers" which are good solution for develop
user friendly graphic user interface.
General features:
CPU NXP i.MX6Q rev1.2 at 792 MHz
RAM 1GB, 32, 64 bit, DDR3-800/1066
NAND SLC,512MB
LVDS Display TFT 10.1" industrial, 1280x800 resolution
Backlight LED backlight, brightness 350 Cd/m2
Power supply 15 to 30 Vdc
Cc: Domenico Acri <domenico.acri@engicam.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The PHYs embedded in the switch direct there interrupts through the
switch interrupt controllers. Now that devel C has its switch
interrupts connected to the SoC, the PHY interrupts can be used by
phylib. Explicitly include MDIO nodes in the switch device tree nodes,
and link the PHY interrupts back to the switch interrupt
controller. Also, link the ports to the PHYs on the MDIO bus.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
