An alias name should have an index number even when it is the only of its type.
This allows U-Boot to add the local-mac-address property. Otherwise U-Boot
skips the alias.
Fixes: 6a93792774 ("ARM: bcm2835: dt: Add the ethernet to the device trees")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Eric Anholt <eric@anholt.net>
According to the BCM2835 ARM Peripherals document uart1 doesn't map to pins
36-39, but uart0 does.
Also, split into separate Rx/Tx and CST/RTS groups to match other uart nodes.
Fixes: 21ff843931 ("ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Eric Anholt <eric@anholt.net>
According to the BCM2835 ARM Peripherals document i2c0 doesn't map to pins 32,
34 but to 28, 29.
Fixes: 21ff843931 ("ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Eric Anholt <eric@anholt.net>
Downstream kernel uses pins 32, 33 as UART0 (PL011) Rx/Tx to communicate with
the Bluetooth chip. So ALT3 of these pins is most likely not CTS/RTS. Change
the node name to reflect that. This matches section 6.2 "Alternative Function
Assignments" in the BCM2835 ARM Peripherals document.
With this change in place, adding
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_gpio32 &gpclk2_gpio43>;
status = "okay";
};
to bcm2837-rpi-3-b.dts does the right thing on my Raspberry Pi 3.
Pins 30, 31 are CTS/RTS of UART0 in alternate function 3. Rename uart0_gpio30
as well.
While at it, fix a little typo in a nearby comment.
Fixes: 21ff843931 ("ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.")
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Eric Anholt <eric@anholt.net>
mmc2 used for wl12xx was missing the keep-power-in suspend
parameter. As a result the board couldn't reach suspend state.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Orange Pi Zero board features a USB OTG port, which has a ID pin, and
can be used to power up the board. However, even if the board is powered
via +5V pin in GPIO/expansion headers, the VBUS in the OTG port cannot
be powered up, thus it's impossible to use it in host mode with simple
OTG cables.
Add support for it in peripheral mode.
If someone really want to use it in host mode, the mode of PHY can be
switch via sysfs, then use a powered USB OTG cable or powered USB HUB to
power up external USB devices.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Orange Pi One features a MicroUSB port that can work in both host mode
and peripheral mode.
When in host mode, its VBUS is controlled via a GPIO; when in peripheral
mode, its VBUS cannot be used to power up the board.
Add support for this port.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner H3/H5 have a dual-routed USB PHY0 -- routed to either OHCI/EHCI
or MUSB controller.
Add device nodes for these controllers.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The new Allwinner H5 SoC is pin-compatible to the H3 SoC, but with the
Cortex-A7 cores replaced by Cortex-A53 cores and the MMC controller
updated. So we should really share almost the whole .dtsi.
In preparation for that move the peripheral parts of the existing
sun8i-h3.dtsi into a new sunxi-h3-h5.dtsi.
The actual sun8i-h3.dtsi then includes that and defines the H3 specific
parts on top of it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: also split out mmc and gic, as well as pio and ccu's
compatible, and make drop of skeleton into a seperated patch]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
According to the datasheets provided by Allwinner, both Allwinner H3 and
H5 use GIC-400 as their interrupt controller.
For better device tree reusing, correct the GIC compatible in H3 DTSI to
"arm,gic-400", thus this node can be reused in H5.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
After converting to generic pinconf binding, pinctrl-a10.h is now not
used at all.
Drop its inclusion for H3 DTSI.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The skeleton.dtsi file is now deprecated, and do not exist in ARM64
environment.
Since we will soon reuse most part of H3 DTSI for H5, which is an ARM64
chip, drop skeleton.dtsi inclusion now.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commit makes use of the axp209.dtsi file to define the
AXP209 PMIC. While here, define the rails that are enabled on
this board.
Tested checking the regulator voltage varies according to the
CPU frequency.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This adds the cpu-supply DT property to the cpu0 DT node needed by
the board to adapt the regulator voltage depending on the currently used
OPP.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This adds almost all operating points allowed for the A33 as defined by
fex files available at:
https://github.com/linux-sunxi/sunxi-boards/tree/master/sys_config/a33
There are more possible frequencies in this patch than there are in the
fex files because the fex files only give an interval of possible
frequencies for a given voltage. All supported frequencies are defined
in the original driver code in Allwinner vendor tree.
There are two missing frequencies though: 1104MHz and 1200MHz which
require the CPU to have 1.32V supplied, which is higher than the default
voltage.
Without all A33 boards defining the CPU regulator, we cannot have these
two frequencies as it would cause the CPU to try to run a higher
frequency without "overvolting" which is very likely to crash the CPU.
Therefore, these two frequencies must be enabled on a per-board basis.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
All dts files for the sunxi platform have been switched to the generic
pinconf bindings. As a result, the sunxi specific pinctrl macros are
no longer used.
Remove the #include entry with the following command:
sed --follow-symlinks -i -e '/pinctrl\/sun4i-a10.h/D' \
arch/arm/boot/dts/sun?i*.*
arch/arm/boot/dts/sun9i-a80.dtsi was then edited to remove the extra
empty line.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The old sunxi specific pinctrl bindings are deprecated, in favor of
the new generic pinconf bindings. Also, we are moving towards handling
GPIO pinmux settings that don't require extra bias or drive strength
settings to use the GPIO bindings only.
This patch removes the last instance of the sunxi specific pinctrl
bindings that use the pinctrl header by dropping the pinmux setting
for the audio codec's PA (external amplifier) control GPIO. The pin
is pulled down externally.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This pull request brings in the DT nodes for enabling HDMI audio on
Raspberry Pi, and nodes to describe the DSI and SDHOST hardware
modules (which are still disabled by default).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Pull "Broadcom arm Device Tree fixes for 4.11 (part 2)" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for 4.11,
please pull the following:
- Jon fixes a reboot issue on most Northstar Plus platforms by adding the
"open-source" property to the "gpio-restart" Device Tree nodes
* tag 'arm-soc/for-4.11/devicetree-fixes-2' of http://github.com/Broadcom/stblinux:
ARM: dts: NSP: GPIO reboot open-source
Currently the slope and offset values for calculating the
hot spot temperature of a particular thermal zone is part
of driver data. Pass them here instead and obtain the values
while of node parsing.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently the slope and offset values for calculating the
hot spot temperature of a particular thermal zone is part
of driver data. Pass them here instead and obtain the values
while of node parsing.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently the slope and offset values for calculating the
hot spot temperature of a particular thermal zone is part
of driver data. Pass them here instead and obtain the values
while of node parsing.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently the slope and offset values for calculating the
hot spot temperature of a particular thermal zone is part
of driver data. Pass them here instead and obtain the values
while of node parsing.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add basic support for STM32H743 MCU and his eval board.
The STMicrolectornics's STM32H743 MCU is based on Cortex-M7 core
running up to @400MHz with 2MB internal flash and 1MB internal RAM.
For more details see:
Documentation/arm/stm32/stm32h743-overview.txt
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Add pinmux for rx,tx,cts and rts lines of uart0. This will enable uart0
to use hardware flow control.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable support for W25Q64CVSSIG which is a Winbond 64 Mbit SPI NOR.
At boot you will see the following message:
m25p80 spi1.0: found s25fl064k, expected w25q64
This is because the JEDEC ID for this chip is the same as s25fl064k.
However, this should be harmless since both chips are essentially the
same.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
After the ti-cpufreq driver has been added, we can now drop the
operating-points table present in dra7.dtsi for the cpu and add an
operating-points-v2 table with all OPPs available for all silicon
revisions. Also add necessary data for use by ti-cpufreq to selectively
enable the appropriate OPPs at runtime as part of the operating-points
table.
As we now need to define voltage ranges for each OPP, we define the
minimum and maximum voltage to match the ranges possible for AVS class0
voltage as defined by the DRA7/AM57 Data Manual, with the exception of
using a range for OPP_OD based on historical data to ensure that SoCs
from older lots still continue to boot, even though more optimal voltages
are now the standard. Once an AVS Class0 driver is in place it will be
possible for these OPP voltages to be adjusted to any voltage within the
provided range.
Information from SPRS953, Revised December 2015.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
eviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The operatings-points-v2 table for am4372 was merged before any user of
it was present in the kernel and before the binding had been finalized.
The new ti-cpufreq driver and binding expects the platform specific
properties to be part of the operating-points-v2 table rather than the
cpu node so let's move them there as the only user is the ti-cpufreq
driver.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
eviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Although all PG2.0 silicon may not support 1GHz OPP for the MPU, older
Beaglebone Blacks may have PG2.0 silicon populated and these particular
parts are guaranteed to support the OPP, so enable it for PG2.0 on
am335x-boneblack only.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
eviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
After the ti-cpufreq driver has been added, we can now drop the
operating-points table present in am33xx.dtsi for the cpu and add an
operating-points-v2 table with all OPPs available for all silicon
revisions. Also add necessary data for use by ti-cpufreq to selectively
enable the appropriate OPPs at runtime as part of the operating-points
table.
Information from AM335x Data Manual, SPRS717i, Revised December 2015,
Table 5-7.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
eviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the SATA controller node to the dm8168-evm device tree.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This board has an external oscillator supplying the reference clock
signal for SATA. Its rate is fixed at 100Mhz. Add a corresponding
device tree node.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Though cpsw doesn't support EEE feature, Atheros 8035 provides
automatic EEE support that is enabled by default. This causes
occasional link drops when link partner also announces EEE support.
These link drops occur on both 100Mbit/s and 1000Mbit/s speeds.
So disable EEE advertising completely.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The manufacturing information is stored in the EEPROM. This chip
is an AT24C64 not not (nor has it ever been) 24C02. This patch will
correctly address the EEPROM to read the entire contents and not just
256 bytes (of 0xff).
Fixes: 5e3447a29a ("ARM: dts: LogicPD Torpedo: Add AT24 EEPROM Support")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
