Rename davinci_mdio DT node "ethernet"->"mdio"
This fixes the following DT schemas check errors:
am3517-craneboard.dt.yaml: ethernet@5c030000: $nodename:0: 'ethernet@5c030000' does not match '^mdio(@.*)?'
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM571x/AM572x/AM574x IDK base boards have HDMI output. Add DT nodes to
am57xx-idk-common.dtsi to enable HDMI.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some pinmuxings are obviously wrong, originating from a copy/paste
error. This patch corrects that with the following strategy:
- Set all reserved bits to zero
- Leave drive strength and slew rate as is
- Add sensible pull and hysteresis depending on the function of the pin
- Not used pins are muxed to their reset-value defined by the SoC
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Many peripherals are affected by gpio5/2, not just sensors. One of those
is ethernet phy so network boot is current broken.
Fix by renaming reg_sensors and marking it as "always on". Also add a
comment asking for careful testing if this is to be made dynamic in the
future.
The "peri_3v3" naming is similar to imx6sx-sdb and regulator-name is
same string as in schematics (VPERI_3V3).
Fixes: 09e2b10489 ("ARM: dts: imx6ul-14x14-evk: Add sensors' GPIO regulator")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch sets initial buck regulator modes explicitly to a state this
hardware needs. So a wrong initial mode set by bootloader or pmic itself
does not interfere anymore.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Otherwise, the system will hang if USB driver try to access
portsc register.
Cc: André Draszik <git@andred.net>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the DDR clock controller and pass it's DDR_CLKID_DDR_PLL to the main
(HHI) clock controller as "ddr_clk". The "ddr_clk" is used as one of the
inputs for the audio clock muxes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the DDR clock controller and pass it's DDR_CLKID_DDR_PLL to the main
(HHI) clock controller as "ddr_clk". The "ddr_clk" is used as one of the
inputs for the audio clock muxes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The clock controller driver has provided the XTAL clock so far. This
does not match how the hardware actually works because the XTAL clock is
an actual crystal which is mounted on the PCB.
Add the "xtal" clock to meson.dtsi and replace all references to the
clock controller's CLKID_XTAL with the new xtal clock node.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add missing 2.0GHz, 1.9GHz & 1.8GHz OPPs (for A15 cores) and 1.4GHz
OPP (for A7 cores). Also update common Odroid-XU3 Lite/XU3/XU4
thermal cooling maps to account for new OPPs.
Since some new OPPs are not available on all Exynos5422/5800 boards
modify dts files for Odroid XU3 Lite (limited to 1.8 GHz / 1.3 GHz) &
Peach Pi (limited to 2.0 GHz / 1.3 GHz) accordingly.
This patch uses maximum voltages for new OPPs. This is a temporary
solution till proper Exynos ASV support is added.
Also while at it fix the number of cooling down steps for big cores
(should be 11 instead of 12 on Odroid XU3 Lite and 14 on XU3/XU4).
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
[mszyprow: rebased onto v5.5-rc1 and adapted to recent dts changes,
fixed removal of the 1.4GHz OPP for A7s on Peach-Pi]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Declare Exynos5422/5800 voltage ranges for OPPs for big CPUs
(Cortex-A15) and wcore bus. Couple their voltage supplies as vdd_arm
and vdd_int should be in 300 mV range.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
[k.konieczny: add missing patch description]
Signed-off-by: Kamil Konieczny <k.konieczny@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The "syscon" compatible string was introduced in commit ("cdcce1ee977b
ARM: dts: exynos: Add "syscon" compatible string to chipid node on Exynos5")
to allow sharing of the CHIPID IO region between multiple drivers.
However, such sharing can be also done without an additional compatible
so remove the syscon entry.
Suggested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The LCD panel on AM4 GP EVMs and ePOS boards seems to be
osd070t1718-19ts. The current dts files say osd057T0559-34ts. Possibly
the panel has changed since the early EVMs, or there has been a mistake
with the panel type.
Update the DT files accordingly.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Embedded Artists COM board is based on NXP i.MX7ULP.
It has a BD70528 PMIC from Rohm with discrete DCDC powering option and
improved current observability (compared to the existing NXP i.MX7ULP EVK).
Add the initial support for the board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This enables the Broadcom uart bluetooth driver on uart0 and gives it
ownership of its gpios. In order to use this, you must enable the
following kconfig options:
- CONFIG_BT_HCIUART_BCM
- CONFIG_SERIAL_DEV
This is applicable to rk3288-veyron series boards that use the bcm43540
wifi+bt chips.
As part of this change, also refactor the pinctrl across the various
boards. All the boards using broadcom bluetooth shouldn't touch the
bt_dev_wake pin.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20191127223909.253873-2-abhishekpandit@chromium.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
During definition of the CPU thermal zone of BCM283x SoC family there
was a misunderstanding of the meaning "criticial trip point" and the
thermal throttling range of the VideoCore firmware. The latter one takes
effect when the core temperature is at least 85 degree celsius or higher
So the current critical trip point doesn't make sense, because the
thermal shutdown appears before the firmware has a chance to throttle
the ARM core(s).
Fix these unwanted shutdowns by increasing the critical trip point
to a value which shouldn't be reached with working thermal throttling.
Fixes: 0fe4d2181c ("ARM: dts: bcm283x: Add CPU thermal zone with 1 trip point")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The phy mode should be rgmii-id. For some reason, it used to work with
rgmii-txid but doesn't any more.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull-ups for SAM9 UART/USART TX lines were disabled in a previous
commit. However, several chips in the SAM9 family require pull-ups to
prevent the TX lines from falling (and causing an endless break
condition) when the transceiver is disabled.
From the SAM9G20 datasheet, 32.5.1: "To prevent the TXD line from
falling when the USART is disabled, the use of an internal pull up
is mandatory.". This commit reenables the pull-ups for all chips having
that sentence in their datasheets.
Fixes: 5e04822f7d ("ARM: dts: at91: fixes uart pinctrl, set pullup on rx, clear pullup on tx")
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Cc: Peter Rosin <peda@axentia.se>
Link: https://lore.kernel.org/r/20191203142147.875227-1-inguin@gmx.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add the Performance Monitoring Unit (PMU) device tree node to the H3
.dtsi, which tells DT users which interrupts are triggered by PMU
overflow events on each core. The numbers come from the manual and have
been checked in U-Boot and with perf in Linux.
Tested with perf record and taskset on an OrangePi Zero.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Beelink X2 box comes with a remote. Add a mapping for it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Emlid Neutis N5H3 is a version of Emlid Neutis SoM with H3 instead of H5
inside.
6eeb4180d4 ("ARM: dts: sunxi: h3-h5: Add Bananapi M2+ v1.2 device")
was used as reference.
Signed-off-by: Georgii Staroselskii <georgii.staroselskii@emlid.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
A new variant of Emlid Neutis has been inroduced. This one uses H3
instead of H5. The boards are essentially the same. This commit moves
non-SoC-specific parts out so that the common parts could be reused with
ease.
Signed-off-by: Georgii Staroselskii <georgii.staroselskii@emlid.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The PMU registers are at least 0x18 bytes wide. Meson8b already uses a
size of 0x18. The structure of the PMU registers on Meson8 and Meson8b
is similar but not identical.
Meson8 and Meson8b have the following registers in common (starting at
AOBUS + 0xe0):
#define AO_RTI_PWR_A9_CNTL0 0xe0 (0x38 << 2)
#define AO_RTI_PWR_A9_CNTL1 0xe4 (0x39 << 2)
#define AO_RTI_GEN_PWR_SLEEP0 0xe8 (0x3a << 2)
#define AO_RTI_GEN_PWR_ISO0 0x4c (0x3b << 2)
Meson8b additionally has these three registers:
#define AO_RTI_GEN_PWR_ACK0 0xf0 (0x3c << 2)
#define AO_RTI_PWR_A9_MEM_PD0 0xf4 (0x3d << 2)
#define AO_RTI_PWR_A9_MEM_PD1 0xf8 (0x3e << 2)
Thus we can assume that the register size of the PMU IP blocks is
identical on both SoCs (and Meson8 just contains some reserved registers
in that area) because the CEC registers start right after the PMU
(AO_RTI_*) registers at AOBUS + 0x100 (0x40 << 2).
The upcoming power domain driver will need to read and write the
AO_RTI_GEN_PWR_SLEEP0 and AO_RTI_GEN_PWR_ISO0 registers, so the updated
size is needed for that driver to work.
Fixes: 4a5a27116b ("ARM: dts: meson8: add support for booting the secondary CPU cores")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Raspberry Pi's firmware has a feature to select how much memory to
reserve for its GPU called 'gpu_mem'. The possible values go from 16MB
to 944MB, with a default of 64MB. This memory resides in the topmost
part of the lower 1GB memory area and grows bigger expanding towards the
begging of memory.
It turns out that with low 'gpu_mem' values (16MB and 32MB) the size of
the memory available to the system in the lower 1GB area can outgrow the
interconnect's dma-range as its size was selected based on the maximum
system memory available given the default gpu_mem configuration. This
makes that memory slice unavailable for DMA. And may cause nasty kernel
warnings if CMA happens to include it.
Change soc's dma-ranges to really reflect it's HW limitation, which is
being able to only DMA to the lower 1GB area.
Fixes: 7dbe8c62ce ("ARM: dts: Add minimal Raspberry Pi 4 support")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The MDIO node on BCM5301X had an reversed #address-cells and
#size-cells properties, correct those, silencing checker warnings:
.../linux/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dt.yaml: mdio@18003000: #address-cells:0:0: 1 was expected
Reported-by: Simon Horman <simon.horman@netronome.com>
Fixes: 23f1eca6d5 ("ARM: dts: BCM5301X: Specify MDIO bus in the DT")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Samsung DTS ARM changes for v5.5, part 2
1. Cleanup by adjusting DTS to bindings,
2. Add touch-sensitive buttons to Midas (Galaxy S III family phones),
3. Add GPU/Mali to Exynos542x and Odroid XU3/XU4 family.
* tag 'samsung-dt-5.5-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Add Mali/GPU node on Exynos5420 and enable it on Odroid XU3/4
ARM: dts: exynos: Add support for the touch-sensitive buttons on Midas family
ARM: dts: exynos: Rename children of SysRAM node to "sram"
Link: https://lore.kernel.org/r/20191119142026.7190-1-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
