We should always check if the bus is free, independently if it is a read
or write. It should be done before the first message, though. After
that, we ourselves keep the bus busy. Remove a 'ret' assignment which
only silenced a build warning.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove the seperate functions and use designated constants. As readable
but less overhead. Actually, this is even more readable since the old
function used a mix of "=" and "|=".
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Switch the device tree to the new compatibles introduced in the i2c drivers
to have a common pattern accross all Allwinner SoCs.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c-eg20t driver is for a companion chip to the Intel Atom E600
series processors. These are 32-bit x86 processors so the driver is
only needed on X86_32. Add COMPILE_TEST as an alternative, so that the
driver can still be build-tested elsewhere.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Newer SoCs have so fast input clocks that the ICCL/H registers only
count every second clock to have a meaningful 9-bit range. The driver
was already prepared for that happening, but didn't use it so far.
Add the proper DT configuration for SoCs that need it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Due to misconfiguration, it can happen that the calculated timing
parameters are out of range. Bail out if that happens. We can also
simplify some logic later because of the verified value. Also, make the
printouts of the values more precise by adding the hex-prefixes.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
sh_mobile_i2c_init() could detect wrong settings, but didn't bail out,
so it would continue unconfigured. Fix this.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is what devm was made for. No rollback mechanism needed, remove the
hook parameter from the irq setup function and simplify it. While we are
here change some variables to proper types.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use standard i2c error codes for i2c failures. Also, don't print
something on timeout since it happens regularly with i2c. Simplify some,
logic, too.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
HSI2C module on Exynos5260 differs from current modules in
following ways:
1. HSI2C on Exynos5260 has fifo_depth of 16bytes
2. Module needs to be reset as a part of init sequence.
Hence, Following changes are involved.
1. Add a new compatible string and Updates the Documentation dt bindings.
2. Introduce a variant struct to support the changes in H/W
3. Reset the module during init. Thus, bringing the module back
to default state irrespective of what firmware did with it.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This adds some more warnings to the i2c-arb-gpio-challenge docs to
help encourage people not to use it in their designs unless they have
no choice.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For !CONFIG_PM_RUNTIME, the device were never put back into active
state while resuming.
For CONFIG_PM_RUNTIME, we blindly trusted the device to be inactive
while we were about to handle it at suspend late, which is just too
optimistic.
Even if the driver uses pm_runtime_put_sync() after each tranfer to
return it's runtime PM resources, there are no guarantees this will
actually mean the device will inactivated. The reason is that the PM
core will prevent runtime suspend during system suspend, and thus when
a transfer occurs during the early phases of system suspend the device
will be kept active after the transfer.
To handle both issues above, use pm_runtime_force_suspend|resume() from
the system suspend|resume callbacks.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The smbus block read is not currently supported for imx i2c devices.
This patchset adds the support to imx i2c bus so that blocks of data
can be read using SMbus block reads.(using i2c_smbus_read_block_data()
function from the i2c_core.c.). Tested with 3.10.9 kernel.
Reviewed-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Kaushal Butala <kaushalkernelmailinglist@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull two powerpc fixes from Ben Herrenschmidt:
"Here are a couple of fixes for 3.15. One from Anton fixes a nasty
regression I introduced when trying to fix a loss of irq_work whose
consequences is that we can completely lose timer interrupts on a
CPU... not pretty.
The other one is a change to our PCIe reset hook to use a firmware
call instead of direct config space accesses to trigger a fundamental
reset on the root port. This is necessary so that the FW gets a
chance to disable the link down error monitoring, which would
otherwise trip and cause subsequent fatal EEH error"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: irq work racing with timer interrupt can result in timer interrupt hang
powerpc/powernv: Reset root port in firmware
Pull two btrfs fixes from Chris Mason:
"This has two fixes that we've been testing for 3.16, but since both
are safe and fix real bugs, it makes sense to send for 3.15 instead"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: send, fix incorrect ref access when using extrefs
Btrfs: fix EIO on reading file after ioctl clone works on it
Pull two ceph fixes from Sage Weil:
"The first patch fixes a problem when we have a page count of 0 for
sendpage which is triggered by zfs. The second fixes a bug in CRUSH
that was resolved in the userland code a while back but fell through
the cracks on the kernel side"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
crush: decode and initialize chooseleaf_vary_r
libceph: fix corruption when using page_count 0 page in rbd
Pull xfs fixes from Dave Chinner:
"Code inspection of the XFS error number sign translations found a
bunch of issues, including returning incorrectly signed errors for
some data integrity operations.
These leak to userspace and result in applications not getting the
errors correctly reported. Hence they need fixing sooner rather than
later.
A couple of the bugs are in data integrity operations, a couple more
are in the new COLLAPSE_RANGE code. One of these came in through a
recent ext4 merge and so I had to update the base tree to 3.15-rc5
before fixing the issues"
* tag 'xfs-for-linus-3.15-rc6' of git://oss.sgi.com/xfs/xfs:
xfs: list_lru_init returns a negative error
xfs: negate xfs_icsb_init_counters error value
xfs: negate mount workqueue init error value
xfs: fix wrong err sign on xfs_set_acl()
xfs: fix wrong errno from xfs_initxattrs
xfs: correct error sign on COLLAPSE_RANGE errors
xfs: xfs_commit_metadata returns wrong errno
xfs: fix incorrect error sign in xfs_file_aio_read
xfs: xfs_dir_fsync() returns positive errno
Pull renameat2 arch support from Miklos Szeredi:
"I've collected architecture patches for the renameat2 syscall that
maintainers acked and/or asked me to queue.
This adds architecture support for the renameat2 syscall to m68k,
parisc, ia64 and through asm-generic to arc, arm64, c6x, hexagon,
metag, openrisc, score, tile, unicore32"
* 'renameat2' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
scripts/checksyscalls.sh: Make renameat optional
asm-generic: Add renameat2 syscall
ia64: add renameat2 syscall
parisc: add renameat2 syscall
m68k: add renameat2 syscall
Pull iommu fixes from Joerg Roedel:
"Three fixes for the AMD IOMMU driver:
- fix a locking issue around get_user_pages()
- fix two issues with device aliasing and exclusion range handling"
* tag 'iommu-fixes-v3.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: fix enabling exclusion range for an exact device
iommu/amd: Take mmap_sem when calling get_user_pages
iommu/amd: Fix interrupt remapping for aliased devices
Pull iscsi_ibft fix from Konrad Rzeszutek Wilk:
"Fix iBFT regression on Broadcom NICs introduced in 3.2"
* tag 'stable/for-linus-3.15-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/ibft:
iscsi_ibft: Fix finding Broadcom specific ibft sign
Pull SH driver fix from Simon Horman:
"Compile drivers/sh/pm_runtime.c if ARCH_SHMOBILE_MULTI
This resolves a regression introduced in v3.14 by commit bf98c1eac1
("ARM: Rename ARCH_SHMOBILE to ARCH_SHMOBILE_LEGACY")"
* tag 'renesas-sh-drivers-for-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
drivers: sh: compile drivers/sh/pm_runtime.c if ARCH_SHMOBILE_MULTI
Pull media fixes from Mauro Carvalho Chehab:
"Most of the changes are drivers fixes (rtl28xuu, fc2580, ov7670,
davinci, gspca, s5p-fimc and s5c73m3).
There is also a compat32 fix and one infoleak fixup at the media
controller"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] V4L2: fix VIDIOC_CREATE_BUFS in 64- / 32-bit compatibility mode
[media] V4L2: ov7670: fix a wrong index, potentially Oopsing the kernel from user-space
[media] media-device: fix infoleak in ioctl media_enum_entities()
[media] fc2580: fix tuning failure on 32-bit arch
[media] Prefer gspca_sonixb over sn9c102 for all devices
[media] media: davinci: vpfe: make sure all the buffers unmapped and released
[media] staging: media: davinci: vpfe: make sure all the buffers are released
[media] media: davinci: vpbe_display: fix releasing of active buffers
[media] media: davinci: vpif_display: fix releasing of active buffers
[media] media: davinci: vpif_capture: fix releasing of active buffers
[media] s5p-fimc: Fix YUV422P depth
[media] s5c73m3: Add missing rename of v4l2_of_get_next_endpoint() function
[media] rtl28xxu: silence error log about disabled rtl2832_sdr module
[media] rtl28xxu: do not hard depend on staging SDR module
Pull staging driver fixes from Greg KH:
"Here are five staging driver fixes for 3.15-rc6 that resolve some
reported issues. They are for the imx and rtl8723au drivers"
* tag 'staging-3.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: rtl8723au: Do not reset wdev->iftype in netdev_close()
staging: rtl8723au: Use correct pipe type for USB interrupts
imx-drm: imx-tve: correct DDC property name to 'ddc-i2c-bus'
imx-drm: imx-drm-core: skip components whose parent device is disabled
imx-drm: imx-drm-core: fix imx_drm_encoder_get_mux_id
Pull driver core fixes from Greg KH:
"Here are two driver core (well, sysfs) fixes for 3.15-rc6 that resolve
some reported issues and a regression from 3.13"
* tag 'driver-core-3.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
sysfs: make sure read buffer is zeroed
kernfs, sysfs, cgroup: restrict extra perm check on open to sysfs
Pull PCI fixes from Bjorn Helgaas:
"These are fixes for an SHPCHP hotplug regression, a "wait for pending
transaction" problem (used in device reset paths), and an email
address update.
PCI device hotplug:
- Fix SHPCHP bus speed mismatch issue (Marcel Apfelbaum)
Miscellaneous:
- Fix pci_wait_for_pending_transaction() (Gavin Shan)
- Update email address (Ben Hutchings)"
* tag 'pci-v3.15-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Wrong register used to check pending traffic
PCI: shpchp: Check bridge's secondary (not primary) bus speed
PCI: Update my email address
Pull /dev/random fix from Ted Ts'o:
"This fixes a BUG_ON-causing regression that was introduced during the
last merge window"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: fix BUG_ON caused by accounting simplification
Pull clock framework fixes from Mike Turquette:
"Clock framework and driver fixes, all of which fix user-visible
regressions.
As usual most fixes are for platform-specific clock drivers, but there
are also two fixes to the clk core after recent changes to the way
that clock unregistration is handled"
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux:
clk: tegra: Fix wrong value written to PLLE_AUX
clk: shmobile: clk-mstp: change to using clock-indices
clk: Fix slab corruption in clk_unregister()
clk: Fix double free due to devm_clk_register()
clk: socfpga: fix clock driver for 3.15
clk: divider: Fix best div calculation for power-of-two and table dividers
clk: bcm281xx: don't use unnamed structs or unions
Pull spi fixes from Mark Brown:
"A few core fixes around outlying cases here, nothing that should
affect most users but useful fixes. The diffstat is rather larger
than one might hope due some simple code motion in the fix for
!CONFIG_DMA, the actual meaningful change is much smaller.
- Fix handling of unsupported dual and quad mode support on slave
registration so that drivers that can degrade gracefully do so,
preventing regressions for drivers this is added.
- Fix build in !CONFIG_DMA cases following addition of generic DMA
mapping support.
- Fix error handling for queue creation which due to wider kernel
changes can be triggered more easily.
- A couple of driver specific fixes"
* tag 'spi-v3.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi/pxa2xx: Prevent DMA from transferring too many bytes
spi: core: Don't destroy master queue if we fail to create it
spi: qup: Fix return value checking for pm_runtime_get_sync()
spi: core: Protect DMA code by #ifdef CONFIG_HAS_DMA
spi: core: Ignore unsupported Dual/Quad Transfer Mode bits
Pull GPIO fixes from Linus Walleij:
- fix a null pointer bug in the ICH6 chipset driver
- fix device tree registration for the mcp23s08 driver
* tag 'gpio-v3.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: mcp23s08: Bug fix of SPI device tree registration.
gpio: ich: set regs and reglen for i3100 and ich6 chipset
Pull more cgroup fixes from Tejun Heo:
"Three more patches to fix cgroup_freezer breakage due to the recent
cgroup internal locking changes - an operation cgroup_freezer was
using now requires sleepable context and cgroup_freezer was invoking
that while holding a spin lock. cgroup_freezer was using an overly
elaborate hierarchical locking scheme.
While it's possible to convert the hierarchical spinlocks directly to
mutexes, this patch simplifies the overall locking so that it uses a
global mutex. This has the added benefit of avoiding iterating
potentially huge number of tasks under a spinlock. While the patch is
on the larger side in the devel cycle, the changes made are mostly
straight-forward and the locking logic is a lot simpler afterwards"
* 'for-3.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: fix rcu_read_lock() leak in update_if_frozen()
cgroup_freezer: replace freezer->lock with freezer_mutex
cgroup: introduce task_css_is_root()
Pull libata fixes from Tejun Heo:
"Mostly device-specific fixes. The only thing which isn't is the fix
for zpodd oops-on-detach bug"
* 'for-3.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: imx: PLL clock needs 100us to settle down
ata: pata_at91 only works on sam9
libata: clean up ZPODD when a port is detached
ahci: imx: software workaround for phy reset issue in resume
ahci: imx: add namespace for register enums
ahci: disable DEVSLP for Intel Valleyview
Pull crypto fixes from Herbert Xu:
"This fixes a NULL pointer dereference on allocation failure in caam,
as well as a regression in the ctr mode on s390 that was added with
the recent concurrency fixes"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: s390 - fix aes,des ctr mode concurrency finding.
crypto: caam - add allocation failure handling in SPRINTFCAT macro
Pull scsi target fixes from Nicholas Bellinger:
"This series include:
- Close race between iser-target network portal shutdown + accepting
new connection logins (sagi)
- Fix free-after-use regression in tcm_fc post conversion to
percpu-ida pre-allocation (nab)
- Explicitly disable Immediate + Unsolicited Data for iser-target
connections when T10-PI is enabled (sagi + nab)
- Allow pi_prot_type + emulate_write_cache attributes to be set to
zero regardless of backend support (andy)
- memory leak fix (mikulas)"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: fix memory leak on XCOPY
target: Don't allow setting WC emulation if device doesn't support
iscsi-target: Disable Immediate + Unsolicited Data with ISER Protection
tcm_fc: Fix free-after-use regression in ft_free_cmd
iscsi-target: Change BUG_ON to REJECT in iscsit_process_nop_out
Target/iscsi,iser: Avoid accepting transport connections during stop stage
Target/iser: Fix iscsit_accept_np and rdma_cm racy flow
Target/iser: Fix wrong connection requests list addition
target: Allow non-supporting backends to set pi_prot_type to 0
