The SDHCI controller instantiated on Tegra114 is not backwards-
compatible with the version on Tegra30, so remove the corresponding
compatible string.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The parent clocks are determined by the output that will be used, not by
the display controller that drives the output. On previous generations a
simple RGB output used to be part of the display controller and hence an
explicit parent clock needed to be assigned to the display controller to
drive the RGB output. Starting with Tegra124, that RGB output has been
dropped and the parent clock can therefore be removed from the display
controller device tree nodes.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The display controller on Tegra114 is in fact not backwards-compatible
with the instantiation found on earlier SoCs. Drop the misleading
compatible string.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The instantiation of gr3d in Tegra114 is not backwards-compatible with
the version found on earlier chips. Remove the misleading compatible
string.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The instantiation of gr2d in Tegra114 is not backwards-compatible with
the version found on earlier chips. While the hardware IP is identical,
the compatible string also describes the integration of the IP, which
in the case of Tegra114 is slightly different in that it's part of the
HEG power partition, whereas it wasn't previously.
Drop the misleading compatible string so that drivers that support the
older integrations cannot match on it. Since they wouldn't be able to
control the power partition, such driver wouldn't be able to access any
of the registers of the IP.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The host1x device tree bindings require the clock- and interrupt-names
properties to be present, so add them where missing.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The correct DSI/CSI supply property is called vdd-dsi-csi-supply, so use
that instead of the wrong vdd-supply property.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The correct DSI/CSI supply property is called vdd-dsi-csi-supply, so use
that instead of the wrong vdd-supply property.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The standard way to do this is to list out the regulators at the top
level. Adopt the standard way to fix validation.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The standard way to do this is to list out the clocks at the top-level.
Adopt the standard way to fix validation.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra SDHCI controller bindings state that the clock-names property
is required, so add the missing properties on Tegra114.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The WDOG_ANY signal is connected to the RESET_IN signal of the SoM
and baseboard. It is currently configured as push-pull, which means
that if some external device like a programmer wants to assert the
RESET_IN signal by pulling it to ground, it drives against the high
level WDOG_ANY output of the SoC.
To fix this we set the WDOG_ANY signal to open-drain configuration.
That way we make sure that the RESET_IN can be asserted by the
watchdog as well as by external devices.
Fixes: 1ea4b76cdf ("ARM: dts: imx6ul-kontron-n6310: Add Kontron i.MX6UL N6310 SoM and boards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The watchdog's WDOG_ANY signal is used to trigger a POR of the SoC,
if a soft reset is issued. As the SoM hardware connects the WDOG_ANY
and the POR signals, the watchdog node itself and the pin
configuration should be part of the common SoM devicetree.
Let's move it from the baseboard's devicetree to its proper place.
Fixes: 1ea4b76cdf ("ARM: dts: imx6ul-kontron-n6310: Add Kontron i.MX6UL N6310 SoM and boards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The FA2 mailbox is specified at 0x18025000 but should actually be
0x18025c00, length 0x400 according to socregs_nsp.h and board_bu.c. Also
the interrupt was off by one and should be GIC SPI 151 instead of 150.
Fixes: 17d5171723 ("ARM: dts: NSP: Add mailbox (PDC) to NSP")
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
A test with the command below gives for example this error:
arch/arm/boot/dts/rk3288-tinker.dt.yaml: tsadc: otp-gpio:
{'phandle': [[54]], 'rockchip,pins': [[0, 10, 0, 118]]}
is not of type 'array'
'gpio' is a sort of reserved nodename and should not be used
for pinctrl in combination with 'rockchip,pins', so change
nodes that end with 'gpio' to end with 'pin' or 'pins'.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/
dtschema/schemas/gpio/gpio.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200524160636.16547-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Since commit cd28d1d6e5 ("net: phy: at803x: Disable phy delay for
RGMII mode") the networking is broken on the BeagleBone AI which has
the AR8035 PHY for Gigabit Ethernet [0]. The fix is to switch from
phy-mode = "rgmii" to phy-mode = "rgmii-rxid".
Note: Grygorii made a similar DT fix for other AM57xx boards with a
different phy in commit 820f8a870f ("ARM: dts: am57xx: fix networking
on boards with ksz9031 phy").
[0] https://git.io/Jf7PX
Fixes: 520557d485 ("ARM: dts: am5729: beaglebone-ai: adding device tree")
Cc: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
I accidentally flipped the system timer to use system clock instead of
the 32k source clock.
Fixes: 14b1925a72 ("ARM: dts: Configure system timers for omap4")
Signed-off-by: Tony Lindgren <tony@atomide.com>
While testing the recent suspend and resume regressions I noticed that
duovero can still end up losing edge gpio interrupts on runtime
suspend. This causes NFSroot easily stopping working after resume on
duovero.
Let's fix the issue by using gpio level interrupts for smsc as then
the gpio interrupt state is seen by the gpio controller on resume.
Fixes: 731b409878 ("ARM: dts: Configure duovero for to allow core retention during idle")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently the PL330 is enabled by default. However if left in IDM reset, as is
the case with the Meraki and Synology NSP devices, the system will hang when
probing for the PL330's AMBA peripheral ID. We therefore should be able to
disable it in these cases.
The PL330 is also included among of the list of peripherals put into coherent
mode, so "dma-coherent" has been added here as well.
Fixes: 5fa1026a3e ("ARM: dts: NSP: Add PL330 support")
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Sleep pin configuration is refined for low power modes:
- "sleep" (no wakeup & console suspend enabled): put pins in analog state
to optimize power
- "idle" (wakeup capability): keep Rx pin in alternate function
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Driver doesn't use interrupt's name to get it so remove it from
the node.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Driver doesn't use interrupt's name to get it so remove it from
the node.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Rename pwm pinctrl nodes name to matching with yaml bindings
requirements.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Driver doesn't use interrupt's name to get it so remove it from
the node.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
