Enable the second EHCI controller on the AST2600. Also add a line-name
for the GPIO that controls power to the USB port.
The power control is in place to allow the port to be disabled, for
those that are worried about rogue USB sticks.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Rainier uses the P10 processor so the OCC binding should reflect that.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add the four SPI masters on each CFAM. Each master has four 128KB EEPROM
devices attached to it.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Adding pca9552 exposes the presence detect lines for the cards and
tca9554 exposes the presence details for the cards.
Signed-off-by: Jet Li <Jet.Li@ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Initial introduction of AMD EthanolX platform equipped with an
Aspeed ast2500 BMC manufactured by AMD.
AMD EthanolX platform is an AMD customer reference board with an
Aspeed ast2500 BMC manufactured by AMD.
This adds AMD EthanolX device tree file including the flash layout
used by EthanolX BMC machines.
Signed-off-by: Supreeth Venkatesh <supreeth.venkatesh@amd.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
We have a 4-bus mux whose output is selected by two GPIO inputs. Wire it
up in the devicetree and ensure the output is enabled by hogging the
appropriate line.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Since commit bcf3440c6d ("net: phy: micrel: add phy-mode support for the
KSZ9031 PHY") the networking is broken on keystone-k2g-evm board.
The above board have phy-mode = "rgmii-id" and it is worked before because
KSZ9031 PHY started with default RGMII internal delays configuration (TX
off, RX on 1.2 ns) and MAC provided TX delay by default.
After above commit, the KSZ9031 PHY starts handling phy mode properly and
enables both RX and TX delays, as result networking is become broken.
Fix it by switching to phy-mode = "rgmii-rxid" to reflect previous
behavior.
Fixes: bcf3440c6d ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
arm64: dts: amlogic: updates for v5.9 (round 2)
- new board: WeTek Core2
- audio playback support on more boards
- add GPU DVFS
* tag 'amlogic-dt64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: dts: amlogic: meson-g12: add the Mali OPP table and use DVFS
arm64: dts: amlogic: meson-gxm: add the Mali OPP table and use DVFS
arm64: dts: amlogic: meson-gx: add the Mali-450 OPP table and use DVFS
arm64: dts: meson: add support for the WeTek Core 2
dt-bindings: arm: amlogic: add support for the WeTek Core 2
arm64: dts: meson: add audio playback to khadas-vim3l
arm64: dts: meson: add audio playback to odroid-c4
arm64: dts: meson: update spifc node name on Khadas VIM3/VIM3L
ARM: dts: meson: Align L2 cache-controller nodename with dtschema
arm64: dts: meson-gxl-s805x: reduce initial Mali450 core frequency
arm64: dts: meson: add missing gxl rng clock
soc: amlogic: meson-gx-socinfo: Fix S905X3 and S905D3 ID's
Link: https://lore.kernel.org/r/7h8sf8671u.fsf@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
mvebu fixes for 5.8 (part 1)
- DT change for Armada 38x allowing to add the register needed to fix
NETA lockup when repeatedly switching speed.
* tag 'mvebu-fixes-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
ARM: dts: armada-38x: fix NETA lockup when repeatedly switching speeds
mvebu dt for 5.9 (part 1)
- Fix the reg-init PHY for the dlink-dns327l (Armada 370)
- Replace HTTP links with HTTPS one in device tree of the Excito
Bubba B3 (Kirkwood)
* tag 'mvebu-dt-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
ARM: dts: dlink-dns327l: fix reg-init PHY
ARM: dts: kirkwood: Replace HTTP links with HTTPS ones
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
To support the change in "phy: armada-38x: fix NETA lockup when
repeatedly switching speeds" we need to update the DT with the
additional register.
Fixes: 14dc100b44 ("phy: armada38x: add common phy support")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Enable pwm_tacho device for fan control and monitoring in Wedge40.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Enable ADC controller and corresponding voltage sensoring channels for
Wedge40.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Disable i2c bus #9, #10 and #13 as these i2c controllers are not used on
Wedge40.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Create all the i2c switches in device tree and use aliases to assign
child channels with consistent bus numbers.
Besides, "i2c-mux-idle-disconnect" is set for all the i2c switches to
avoid potential conflicts when multiple devices (beind the switches)
use the same device address.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The GPIO on Q0 is used for resetting the CFAM of the processor that the
ASPEED master is connected to.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The GPIO on Q0 is used for resetting the CFAM of the processor that the
ASPEED master is connected to.
The signal is wired as active high on the first pass systems.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Pull clock event/surce driver changes from Daniel Lezcano:
- Add sama5d2 support and rework the 32kHz clock handling (Alexandre Belloni)
- Add the high resolution support for SMP/SMT on the Ingenic timer (Zhou Yanjie)
- Add support for i.MX TPM driver with ARM64 (Anson Huang)
- Fix typo by replacing KHz to kHz (Geert Uytterhoeven)
- Add 32kHz support by setting the minimum ticks to 5 on Nomadik MTU (Linus Walleij)
- Replace HTTP links with HTTPS ones for security reasons (Alexander A. Klimov)
- Add support for the Ingenic X1000 OST (Zhou Yanjie)
Biggest part is the addition of the rk3288 variant of the VMARC
SOM and it's Rock Pi N8 icarnation. This brings some arm64 dts-changes
with it as the underlying Dalang carrier board is shared by both
an arm32 rk3288 SOM and an arm64 rk3399 SOM (Rock Pi N10).
Other than that rk3288 gets its ohci node added that only works
on the fixed rk3288w variant of the soc and some asorted fixes
and improvements for dt-binding-check.
* tag 'v5.9-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Add PCIe for RockPI N10
ARM: dts: rockchip: Add HDMI out for RockPI N8/N10
ARM: dts: rockchip: Add USB for RockPI N8/N10
ARM: dts: rockchip: Add usb host0 ohci node for rk3288
ARM: dts: rockchip: Fix VBUS on rk3288-vyasa
ARM: dts: rockchip: Add Radxa Rock Pi N8 initial support
ARM: dts: rockchip: Add VMARC RK3288 SOM initial support
dt-bindings: arm: rockchip: Add Rock Pi N8 binding
arm64: dts: rk3399pro: vmarc-som: Move common properties into Carrier
arm64: dts: rk3399pro: vmarc-som: Move supply regulators into Carrier
arm64: dts: rk3399pro: vmarc-som: Fix sorting nodes, properties
ARM: dts: rockchip: dalang-carrier: Move i2c nodes into SOM
ARM: dts: rockchip: Add 'arm,pl330-periph-burst' for dmac
ARM: dts: rockchip: Add marvell BT irq config
ARM: dts: rockchip: rename label and nodename pinctrl subnodes that end with gpio
Link: https://lore.kernel.org/r/2472314.kD9Egx1jfM@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This enables the audio SRAM, DMA engine, I2S interface, and codec, hooks
them together and adds a audio-graph-card instance.
It also removes the jack gpios from the gpio-keys instance, because the
audio jack driver registers an input device.
Link: https://lore.kernel.org/r/20200718205019.184927-10-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
On the XO-1.75, this node represents a bus interface that operates in slave
mode and thus is only able to accommodate a single subnode; no address
cells are necessary.
The Documentation/devicetree/bindings/spi/spi-controller.yaml binding
prefers that we drop the property instead of setting it to zero.
This fixes a DT validation error:
arch/arm/boot/dts/mmp2-olpc-xo-1-75.dt.yaml: spi@d4037000:
{ ... } is valid under each of {'required': ['spi-slave']},
{'required': ['#address-cells']}
We also need to drop #size-cells:
arch/arm/boot/dts/mmp2-olpc-xo-1-75.dt.yaml: spi@d4037000:
'#address-cells' is a dependency of '#size-cells'
Link: https://lore.kernel.org/r/20200718205019.184927-3-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
mmp2-olpc-xo-1-75.dt.yaml: camera_i2c: $nodename:0:
'camera_i2c' does not match '^i2c(@.*)?'
mmp2-olpc-xo-1-75.dt.yaml: camera_i2c: 'sda-gpios' is a required property
mmp2-olpc-xo-1-75.dt.yaml: camera_i2c: 'scl-gpios' is a required property
The "gpios" property actually was documented as deprecated, but got dropped
in commit 0175ce4a58 ("dt-bindings: i2c: Convert i2c-gpio binding to
json-schema"). It's probably best kept forgotten though.
Link: https://lore.kernel.org/r/20200718205019.184927-2-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
STM32 DT updates for v5.9, round 1
Highlights:
----------
MCU part:
-Enable stmpe811 on stm32f429
-Enable l3gd20-gyro on stm32f429
-Enable panel-ilitek-9341 on stm32f429
-Fixes for yaml validation (leds, nodes names,
remove useless bindings ...)
-Add stm32xxx compatibles for syscon nodes
MPU part:
-Add support for usb role switch to dwc2
-Add stm32xxx compatibles for syscon nodes
-Update uart4 pin configuration for low power mode
used by dkx and ed1 ST boards
-Fix uart nodes ordering and uart7_pins_a comments
-Add the support of uart instances available on STM32MP157 boards:
- usart3 on stm32mp157c-ev1, stm32mp157a-dk1, and stm32mp157c-dk2
- uart7 on stm32mp157a-dk1 and stm32mp157c-dk2
- usart2 on stm32mp157c-dk2
-Configure I2C5 on stm32mp15 DK boards
* tag 'stm32-dt-for-v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (38 commits)
ARM: dts: stm32: enable usb-role-switch on USB OTG on stm32mp15xx-dkx
ARM: dts: stm32: Add compatibles for syscon for stm32mp151
ARM: dts: stm32: Add compatibles for syscon for stm32h743
ARM: dts: stm32: Add compatibles for syscon for stm32f746
ARM: dts: stm32: Add compatibles for syscon for stm32f426
dt-bindings: arm: stm32: Add compatibles for syscon nodes
ARM: dts: stm32: Fix spi4 pins in stm32mp15-pinctrl
ARM: dts: stm32: configure i2c5 support on stm32mp15xx-dkx
ARM: dts: stm32: add usart2 node to stm32mp157c-dk2
ARM: dts: stm32: add uart7 support to stm32mp15xx-dkx boards
ARM: dts: stm32: add usart3 node to stm32mp157c-ev1
ARM: dts: stm32: add usart3 node to stm32mp15xx-dkx boards
ARM: dts: stm32: add usart2, usart3 and uart7 pins in stm32mp15-pinctrl
ARM: dts: stm32: cosmetic updates in stm32mp15-pinctrl
ARM: dts: stm32: fix uart7_pins_a comments in stm32mp15-pinctrl
ARM: dts: stm32: fix uart nodes ordering in stm32mp15-pinctrl
ARM: dts: stm32: Update UART4 pin states on stm32mp15xx-dkx
ARM: dts: stm32: Update pin states for uart4 on stm32mp157c-ed1
ARM: dts: stm32: update uart4 pin configuration for low power on stm32mp157
dt-bindings: usb: dwc2: Fix issues for stm32mp15x SoC
...
Link: https://lore.kernel.org/r/8a9bb27b-fc08-126a-11f7-01354e8577e1@st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Samsung DTS ARM changes for v5.9
1. Enable Bluetooth on Artik5 (Exynos3250).
2. Enable accelerometer on Aries boards (Samsung Galaxy S family,
S5Pv210); multiple fixes.
3. Fix highest frequencies on Exynos5800.
4. Fix rare USB instability on Odroid XU3 family (Exynos5422).
5. Minor DTS fixes and adjustments with dtschema.
* tag 'samsung-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Replace HTTP links with HTTPS ones
ARM: dts: exynos: Disable frequency scaling for FSYS bus on Odroid XU3 family
ARM: dts: exynos: Define fixed regulators in root node for consistency in SMDK5420
ARM: dts: exynos: Define fixed regulators in root node for consistency in Arndale
ARM: dts: exynos: Define fixed regulators in root node for consistency in Origen
ARM: dts: exynos: Remove DMA controller bus node name to fix dtschema warnings
ARM: dts: exynos: Fix missing empty reg/ranges property regulators on Trats
ARM: dts: exynos: Align L2 cache-controller nodename with dtschema
ARM: dts: s5pv210: Correct BCM4329 bluetooth node
ARM: dts: s5pv210: Add BMA023 accelerometer support to Aries
ARM: dts: s5pv210: Add support for GP2A light sensor on Aries
ARM: dts: s5pv210: Correct fuelgauge definition on Aries
ARM: dts: s5pv210: Add interrupt-controller property to gph3
ARM: dts: exynos: Enable Bluetooth support for Artik5 board
ARM: dts: exynos: Extend all Exynos5800 A15's OPPs with max voltage data
Link: https://lore.kernel.org/r/20200721180900.13844-2-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Qualcomm ARM dts updates for v5.9
Add QFPROM and ethernet for ipq8064 and a new DTS for the MikroTik
RB3011 using the same platform.
* tag 'qcom-dts-for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: dts: qcom: add qfprom definition to ipq806x
ARM: dts: qcom: Add MikroTik RB3011
ARM: dts: qcom: add ethernet definitions to ipq8064
Link: https://lore.kernel.org/r/20200721045032.3430395-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Our usual number of patches to improve the Allwinner Device Tree
support, including:
- CPUFreq / Thermal throttling support for the H5
- Touchscreen support for the Pinephone
- New boards: PinePhone v1.2
* tag 'sunxi-dt-for-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: h5: bananapi-m2-plus-v1.2: Tie in CPU OPPs
arm64: dts: allwinner: h5: libretech-all-h3-cc: Tie in CPU OPPs
arm64: dts: allwinner: h5: Add CPU Operating Performance Points table
arm64: dts: allwinner: h5: Add trip and cooling maps to CPU thermal zones
arm64: dts: allwinner: h5: Add clock to CPU cores
ARM: dts: sunxi: bananapi-m2-plus-v1.2: Fix CPU supply voltages
ARM: dts: sunxi: bananapi-m2-plus-v1.2: Add regulator supply to all CPU cores
ARM: dts: sunxi: libretech-all-h3-cc: Add regulator supply to all CPU cores
arm64: dts: sun50i-pinephone: dldo4 must not be >= 1.8V
arm64: dts: allwinner: Add support for PinePhone revision 1.2
dt-bindings: arm: sunxi: Add PinePhone 1.2 bindings
arm64: dts: sun50i-a64-pinephone: Add touchscreen support
arm64: dts: sun50i-a64-pinephone: Enable LCD support on PinePhone
ARM: dts: orange-pi-zero-plus2: add leds configuration
ARM: dts: orange-pi-zero-plus2: enable USB OTG port
Link: https://lore.kernel.org/r/fa48ffcb-3404-41bb-b065-a16717cf5688.lettre@localhost
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Versatile DTS changes for the v5.9 kernel cycle, essentially
just a single patch fixing up the node names for schema.
* tag 'versatile-for-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: dts: arm-realview: Align L2 cache-controller nodename with dtschema
Link: https://lore.kernel.org/r/CACRpkdbkM9ZmuG2FnBmO7upcJfnqq2oSLDCFDXC5b3K+dtps9Q@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
i.MX device tree update for 5.9:
- New board support: Protonic PRTI6Q/WD2/VT7/RVT and MYiR MYS-6ULX SBC.
- Update IIM, OCOTP and SD/MMC device node name to match .yaml bindings.
- Make tempmon node as child of anatop node according to hardware
architecture.
- The vf610-zii device update: configure fiber port to 1000BaseX, add
switch watchdog, MDIO speed and preamble.
- A series from Fabio Estevam to update imx6qdl-sabresd and
imx6q-tbs2910 for using MDIO node and reset-assert-us.
- Align L2 cache-controller device node name with .yaml schema.
- Enable SATA support for imx6qp-sabreauto and imx6qp-sabresd board.
- A series of patches from Shengjiu Wang to enable various audio
support on i.MX6 devices.
- Add Gateworks System Controller support for imx6qdl-gw devices.
- Change default #pwm-cells setting to <3> in the SoC dtsi files.
- Other small random changes.
* tag 'imx-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (43 commits)
ARM: dts: vf610-zii-ssmb-spu3: Add node for switch watchdog
ARM: dts: vf610-zii-ssmb-dtu: Add no-sdio/no-sd properties
ARM: dts: imx6q-tbs2910: Pass reset-assert-us
ARM: dts: imx6q-tbs2910: Add an mdio node
ARM: dts: imx6qdl-sabresd: Pass reset-assert-us
ARM: dts: imx6qdl-sabresd: Add an mdio node
ARM: dts: imx6qdl-gw: add Gateworks System Controller support
ARM: dts: imx6ull: add MYiR MYS-6ULX SBC
ARM: dts: vf610-zii-spb4: Add node for switch watchdog
ARM: dts: colibri-imx6: remove pinctrl-names orphan
ARM: dts: imx: default to #pwm-cells = <3> in the SoC dtsi files
ARM: dts: vf610-zii-scu4-aib: Configure fibre ports to 1000BaseX
ARM: dts: vf610-zii-dev-rev-c: Configure fiber port to 1000BaseX
ARM: dts: ZII: update MDIO speed and preamble
ARM: dts: vfxxx: Add node for CAAM
ARM: dts: imx6qp-sabresd: enable sata
ARM: dts: imx6qp-sabreauto: enable sata
ARM: dts: add Protonic RVT board
ARM: dts: add Protonic VT7 board
ARM: dts: add Protonic WD2 board
...
Link: https://lore.kernel.org/r/20200720085536.24138-3-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
i.MX fixes for 5.8, round 3:
- A couple of FEC2 phy-mode fixes on imx6sx-sabreauto and imx6sx-sdb
board.
- One fix on imx6qdl-icore pin muxing to get USB OTG_ID and SD card
detect work correctly.
* tag 'imx-fixes-5.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6qdl-icore: Fix OTG_ID pin and sdcard detect
ARM: dts: imx6sx-sabreauto: Fix the phy-mode on fec2
ARM: dts: imx6sx-sdb: Fix the phy-mode on fec2
Link: https://lore.kernel.org/r/20200720040148.GA20462@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Two fixes for the Allwinner SoCs, one to relax the CMA allocation ranges that
were failing on older SoCs and one to fix Cedrus on the H6.
* tag 'sunxi-fixes-for-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: h6: Fix Cedrus IOMMU usage
ARM: dts sunxi: Relax a bit the CMA pool allocation range
Link: https://lore.kernel.org/r/e24f0608-6a4f-4163-b99e-a5f48e796184.lettre@localhost
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
[nsekhar@ti.com: drop obsolete hawkboard.org URL completeley
fixup subject line prefix]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Now that USB OTG driver supports usb role switch by overriding PHY input
signals (A-Valid, B-Valid and Vbus-Valid), enable it on stm32mp15xx-dkx.
dr_mode needn't to be forced to Peripheral anymore, it is set to OTG in
SoC device tree.
USB role (USB_ROLE_NONE, USB_ROLE_DEVICE, USB_ROLE_HOST) will be provided
by STUSB1600 Type-C controller driver.
This patch depends on "Add STUSB160x Type-C port controller support"
series, which is under review.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
