Ensure SDE_ERROR error log print function name and line number.
Add a macro DISP_DEV_ERR as a wrapper of dev_err to ensure origin dev_err
will print function name and line number.
This would help with analysis of errors reported with automated testing.
Expected display error log format:
[FUNCTION_NAME:line] ERROR_MESSAGE
Change-Id: I354f45b492059d5ba2bb110d56443fd338add7ad
Signed-off-by: GG Hou <quic_renjhou@quicinc.com>
* quic/display-kernel.lnx.5.10:
disp: msm: sde: avoid error during fal10_veto override enablement
disp: msm: update copyright description
disp: msm: sde: configure dest_scaler op_mode for two independent displays
disp: msm: dp: updated copyright set for 4nm target
Revert "disp: msm: sde: consider max of actual and default prefill lines"
disp: msm: sde: Reset backlight scale when HWC is stopped
disp: msm: dp: avoid duplicate read of link status
disp: msm: dsi: update vreg_ctrl settings for cape
disp: msm: fail commit if drm_gem_obj was found attached to a sec CB
disp: msm: dp: updated register values for 4nm target
disp: msm: sde: update framedata event handling
disp: msm: dsi: Add new phy comaptible string for cape
disp: msm: sde: software override for fal10 in cwb enable
disp: msm: update cleanup during bind failure in msm_drm_component_init
disp: msm: sde: dump user input_fence info on spec fence timeout
disp: msm: sde: add null pointer check for encoder current master
disp: msm: dsi: enable DMA start window scheduling for broadcast commands
disp: msm: sde: avoid alignment checks for linear formats
disp: msm: reset thread priority work on every new run
disp: msm: sde: send power on event for cont. splash
disp: msm: sde: always set CTL_x_UIDLE_ACTIVE register to "1"
disp: msm: use vzalloc for large allocations
disp: msm: sde: Add support to limit DSC size to 10k
disp: msm: sde: add tx wait during DMS for sim panel
disp: msm: dsi: add check for any queued DSI CMDs before clock force update
disp: msm: sde: correct pp block allocation during dcwb dither programming
disp: msm: sde: avoid setting of max vblank count
disp: msm: sde: add cached lut flag in sde plane
disp: msm: sde: avoid use after free in msm_lastclose
disp: msm: sde: update TEAR_SYNC_WRCOUNT register before vsync counter
disp: msm: dsi: Support uncompressed rgb101010 format
disp: msm: sde: update idle_pc_enabled flag for all encoders
disp: msm: sde: flush esd work before disabling the encoder
disp: msm: sde: allow qsync update along with modeset
disp: msm: dp: avoid dp sw reset on disconnect path
disp: msm: sde: consider max of actual and default prefill lines
disp: msm: ensure vbif debugbus not in use is disabled
disp: msm: sde: update cached encoder mask if required
disp: msm: sde: while timing engine enabling poll for active region
disp: msm: enable cache flag for dumb buffer
disp: msm: sde: disable ot limit for cwb
disp: msm: sde: avoid race condition at vm release
disp: msm: dsi: set qsync min fps list length to zero
disp: msm: sde: reset mixers in crtc when ctl datapath switches
disp: msm: sde: update vm state atomic check for non-primary usecases
disp: msm: sde: reset CTL_UIDLE_ACTIVE register only if uidle is disabled
Change-Id: If480e7f33743eb4788549f853ba05e744ecb38d3
Signed-off-by: Narendra Muppalla <quic_nmuppall@quicinc.com>
Destination scaler0 and scaler1 when operated in independent mode,
by two built-in independent displays the op_mode gets modified
concurrently and HW flushes new config. This leads to underruns
on both the displays. This change programs the op_mode
correctly to operate ds0 and ds1 independently.
Change-Id: I01a3d4a986e0e7166f8a38b4cf35981d3e434686
Signed-off-by: Jayaprakash Madisetty <quic_jmadiset@quicinc.com>
This change adds Detail Enhancer LPF blend support from MDSS 9.0.
Support is added for qseed block in both SSPP and Destination Scaler.
Change-Id: Ic8e3732059498a156f51fb93c5fd6638bd731c57
Signed-off-by: Narendra Muppalla <quic_nmuppall@quicinc.com>
The sde_hw_blk was meant to be a generic base object for all
SDE HW blocks, however, it enforces using a common set of ops
which is not practical when blocks have different capabilities.
Since this object was never used as intended and is not doing
anything functional today, remove the dead weight.
Change-Id: If76006c1ae5c62e8d7d77b100837dbaf6c661bd3
Signed-off-by: Steve Cohen <quic_cohens@quicinc.com>
Align the HW catalog to use common naming amongst the "revision"
and "version" structure members.
Change-Id: Ib6c81aee6cb49208b0699db4a75b4eb9dc79e800
Signed-off-by: Steve Cohen <quic_cohens@quicinc.com>
This change replaces kzfree with kfree as kzfree has been
renamed.
While moving to the latest 5.10 tip, additional small changes
were required to resolve compilation issues:
set_dma_ops has moved from dma-mapping to dma-map-ops header.
This change includes the new header file required.
drm_panel_add returns void, this change removes the expected
return value check.
drm_prime_pages_to_sg takes an additional parameter. This change
passes in the drm_device pointer the function is looking for.
Remove an unused variable in sde_crtc vblank function.
Change-Id: I47c085c0cb64432873c2e750ae64cbdc2b5340da
Signed-off-by: Samantha Tran <samtran@codeaurora.org>
QSEED scalar block HW revision is constant for a given MDSS revision.
Both SSPP and DS HW files invoke this API to read the revision register
at various points of time. Expose this revision information through
DT binding and maintain in the catalog to avoid repeated register
reads.
Change-Id: I95c0a5242cfda0aaa4ec5c2ff5c7cc0bed191b59
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
This change brings msm display driver including sde,
dp, dsi, rotator, dsi pll and dp pll from base 4.19 kernel
project. It is first source code snapshot from base kernel project.
Change-Id: Iec864c064ce5ea04e170f24414c728684002f284
Signed-off-by: Narendra Muppalla <NarendraM@codeaurora.org>
