Create and send user configurable ini for max number of roam preauth
retries and roam preauth no-ack timeout to the firmware.
Change-Id: I0343cb29952286d9b42a69136fc6353cd86e4752
CRs-Fixed: 2286079
wmi_mtrace is defined as static in wmi_unified_tlv.c and
used in TLV functions, but some TLVs need to be featurized
and moved to separated TLV files. Need to export wmi_mtrace
for external use.
Change-Id: I9459ec01c9cd4a89f3544d6a9831acba56e6a278
CRs-Fixed: 2314779
Host changes to enable HTT version 2 messaging for
PEER map and unmap in FW and changes to handle these
messages in host
Change-Id: Ifbe478212bbbc9c9ea1c1e4791c7a78407c376cc
Currently only 16 bytes of wmi command/event messages are logged
excluding wmi header information.
By enabling WMI_EXT_DBG whole command/event messages can be dumped
using qdf debugfs apis. This will help if it is needed to
collect whole command/event messages information.
Change-Id: I72dff1279b1145b8d2ee415db97656f457c0136f
CRs-Fixed: 2309286
Make the HECAP and HEOP changes for 11ax Draft3.0.
Draft2.0 support can still be enabled by unsetting
SUPPORT_11AX_D3 in config.unified.wlan.profile.
Change-Id: I0c0fd885a43b672baca61011b75a51526481b1ee
CRs-fixed: 2294235
This change is required as a part of setting sifs_rate in the
target through wmi command from host for legacy chipsets.
Change-Id: Ia3ed8a6d33fcb31b290129e1302dfc0000ad4626
CRs-Fixed: 2031293
Add wmi layer support to get firmware roam scan statistics which includes
scoring of roam candidates, channels, old and new bssids etc.,
Change-Id: I3a0aafbe66d12eea40e71ceb4c7c3a60b9d6e04f
CRs-Fixed: 2203904
Add implementation to enhance structure
corresponding to WMI_DCS_INTERFERENCE_EVENT_ID
handler in cp stats component which hold
secondary 40 and 80MHz utilization
which are required parameters of Extended BSS IE
Change-Id: I1c471608394d5c395632742098d2c92fc02ec238
CRs-Fixed: 2298073
In wmi_unified_cmd_send() function, pass function name and
line number of caller and log the same in case of failure,
this approach helps to remove error logs in caller function
there by reducing text segment.
Change-Id: Ib70d55959087021c4495c175d5363375037afe00
CRs-Fixed: 2281983
In wmi_buf_alloc() function, pass function name and
line number of caller and log the same in case of failure,
this approach helps to remove error logs in caller function
there by reducing text segment.
Also add wmi_nofl_* macros.
Change-Id: Ib1ac8bf2bbcefa7f0015aff2733d3dc4773b185d
CRs-Fixed: 2281983
P2P Listen offload is not a requirement for Genoa, hence featurize
P2P listen offload code to save memory foot-print for Genoa.
Change-Id: I3c32b4ee2b37421e49acee4bd20d36e7a8a3bf77
CRs-Fixed: 2304555
1. Service ready ext includes a parameter for max
BSSID indicator.
2. Beacon template includes MBSSID IE offset.
3. Vdev create and up cmds include more parameters.
Change-Id: I71214eacdaa886725b7ea8f61db3a743ba6597e9
CRs-Fixed: 2306638
Add TLV support for estimated airtime calculation.
Add support to send esp_ie_offset along with beacon template.
Change-Id: Ic70ad7df330674a10ac6051f96975aa928700ba3
CRs-Fixed: 2300339
Add new WMI command to support WMM based ATF configuration.
The new WMI command sends the Access category ID and the
corresponding airtime allocation to the firmware.
Change-Id: I7a5fafa6190d779d0fef8982b7b781af54656b19
CRs-Fixed: 2293193
Add/Modify functions to support AC based ATF support.
Modify Function pointer declarations and assignments to
comply with the new design.
Change-Id: I17046c4461dc4ba413fd71a4437c0f7cb8997400
CRs-Fixed: 2293193
Change "qcacmn: Add revised extscan start hotlist monitor API" (Change
Id Ie705f2462c7d5befa691f1ab57293e55ab68e3e2) recently added a revised
"start hotlist" handler. The only known client of the existing
interface was converted to use the new interface with change
"qcacld-3.0: Refine the extscan start BSSID hotlist logic" (Change-Id
I4d9f982177bc61a751ba0e7437fe55482dfd2723) so remove the now obsolete
interface.
Change-Id: I6e43170daa3ed2d932f1f2fa6717ea230a37ea8b
CRs-Fixed: 2294278
pe sessionId should not be used as vdevId.Add
vdevId field to aggr_add_ts_param and use it
in wmi command.
Change-Id: Id021dda35a32f7870277d405c85a0878d7baa3f3
CRs-Fixed: 2293867
Clean up WMI component prints by correcting trace levels for
regularly occurring prints and removing newlines from converged
print APIs since qdf_trace_msg appends them by default.
Change-Id: Ie375e6fda2943f5f2b7287da4374ef9d7470d593
CRs-Fixed: 2243843
WMI_PEER_TWT_REQ and WMI_PEER_TWT_RESP flags are introduced in peer
flags sent to FW in PEER_ASSOC_CMD. Add corresponding flags in host
structure to indicate peer's support for TWT requester and TWT
responder.
Change-Id: Ic5edb594a95b255fe8ce1091d96c4d886b4d6170
CRs-Fixed: 2290026
TWT delete, pause and resume command is upadted by FW to include peer
mac address. Update host implementation to include peer mac in these
commands. Also, resume command is updated to include next_twt_size.
Update resume command for the same.
Change-Id: Iec184d0449b06aaeb9bac558e8cb5322f867e12f
CRs-Fixed: 2279309
ba_window_size_valid and ba_window size support is missing
while sending wmi_peer_reorder_queue_setup. This is needed
for handing 256 BA which is not FW default.
Change-Id: I3218921c48c0f82225b7992076e73ac0acf7bd11
CRs-fixed: 2285423
There is an existing WMI command which is used to start the extscan
hotlist monitor, wmi_unified_get_buf_extscan_hotlist_cmd(), but this
API has multiple issues:
1) The "get_buf" in the name implies it retrieves something, but it
doesn't.
2) The full name is not a "mirror" of the companion function that
stops the monitor, wmi_unified_extscan_stop_hotlist_monitor_cmd().
3) The current function has an "int *buf_len" parameter that is unused.
To address these issue introduce a new function with "mirror" naming,
wmi_unified_extscan_start_hotlist_monitor_cmd(), which has an
appropriate parameter list.
It is expected that all clients of the existing API will be moved to
the new API, at which point the existing API can be removed.
Change-Id: Ie705f2462c7d5befa691f1ab57293e55ab68e3e2
CRs-Fixed: 2289368
Currently wmi_unified_api defines a wmi_unified_vdev_restart_send()
prototype, but there is no implementation of this function. This
discrepancy dates back to the initial introduction of the prototype in
change "qcacmn: Add tlv implementation of common unified API" (Change
Id I7e70b48ef5e1df0c0f81c639579e6eb1a6685dc3). Since this function
does not exist, and in fact has never existed, remove the prototype.
Note that another API, wmi_unified_vdev_start_send(), supports both
start and restart capability.
Change-Id: Ia88d8b1e825c806b454428e72d9731ccefd05c01
CRs-Fixed: 2286613
Currently the 'setratemask' command supports setting
the rate mask for upto MCS0-9 and NSS 4. Add 'lower32_2'
field in the ratemask_params struct to extend support
for the 'setratemask' command to set rate mask
for upto MCS0-11 and NSS 8.
Change-Id: I9c06ae238142dca37df9826ca34449dd34ee6782
CRs-fixed: 2251392
For a full explanation of the problem and phased solution refer to
"qcacmn: Clean up the extscan unified WMI (phase 1)", Change-Id
I11800361b572331cfada00fb7d518c314df20b43, in the qca-wifi-host-cmn
project.
For phase 3 (this change):
Remove the unions introduced in phase 1, leaving just the properly
named replacement identifiers.
Change-Id: Ia14a42a1a767a850fbfd82a5755ddea51246a95d
CRs-Fixed: 2282843
Existing antenna gain command does not take odd antenna gain value that is
gains are not supported in steps of 0.5db. antenna_gain_half_db pdev
param provides this support. Added WMI and CDP changes to configure/read
this data.
CRs-Fixed: 2024854
Change-Id: I47da9eed74a1a0180cefb4c3f47bc4340da1bdfd
For a full explanation of the problem and phased solution refer to
"qcacmn: Clean up the extscan unified WMI (phase 1)", Change-Id
I11800361b572331cfada00fb7d518c314df20b43, in the qca-wifi-host-cmn
project.
For phase 2 (this change):
Replace all references of the badly named identifiers with references
to the properly named substitutes. Note that this phase may touch
multiple repos and may involve a number of separate changes.
Change-Id: Ie19d632faa50b23f18a2214a7b2502830ff3fbd3
CRs-Fixed: 2282767
Add WMI support to send action OUI extensions to firmware.
For STA interface, this feature is intended to control mode of connection,
connected AP's in-activity time, Tx rate etc.,
Change-Id: I6a0bc9d3f7f0d57805b872cae4baa1fe84fb8193
CRs-Fixed: 2254509
The extscan unified data structures were duplicated from legacy
qcacld-3.0 data structures. As part of the duplication process some
things were inherited that are not appropriate in the unified WMI
including camelCase identifiers and the use of "session id" as an
instance identifier. Due to the fact that multiple repos are affected
a multi-phase cleanup is proposed in order to avoid cross-repo
inter-dependent commits.
For phase 1 (this change):
For each inappropriate identifier introduce an anonymous union which
will contain both the badly named identifier and a properly named
substitute.
Subsequent changes will address the following phases:
For phase 2:
Replace all references of the badly named identifiers with references
to the properly named substitutes. Note that this phase may touch
multiple repos and may involve a number of separate changes.
For phase 3:
Once phase 2 completes, remove the unions introduced in phase 1,
leaving just the properly named replacement identifiers.
For phase 4:
Update the legacy code to exclusively use the converged data
structures, abandoning the legacy data structures.
Change-Id: I11800361b572331cfada00fb7d518c314df20b43
CRs-Fixed: 2280645
WMI_VDEV_PARAM_SET_HE_SOUNDING_MODE provides the scope for host
to configure the sounding mode to (VHT or HE). It also provides
(SU or MU) and (Triggered or Non-Triggered) configurability.
Change-Id: Iac566383c5a6b6b3b402526afd2bfa4818f27bc5
CRs-Fixed: 2262752
Add support for sending WMI command to firmware
to measure estimated airtime that a new client
will get and populate the result that firmware
returns in the ESP IE.
Change-Id: Ic5fcb11100ecd0597ba02dfa5512e2f4ff3558c9
CRs-Fixed: 2261469
WMI recording is done per pdev and hence an instance of
debugfs directory (eg: WMI0, WMI1, WMI2 for 3 radio boards)
has to be created in /sys/kernel/debug/ path.
The wmi handle is per pdev and hence is causing the problem of wmi_instance
being 0 always as each pdev has its own wmi_handle.
WMI1 and WMI2 debugfs directories are not created as wmi_instance
is always 0.
WMI debugfs directory is created for every pdev of the psoc and naming
convention is changed to WMI_SOCx_PDEVx.
Change-Id: Ieb7e9d072d84f699588a8f719508c5cd8d9873fb
CRs-Fixed: 2232472
Add definitions for the enum WMI_HOST_SMART_LOG_SCENARIO which defines
individual smart logging scenarios which can be enabled/disabled. Also
add utility macros to set/get the same.
Change-Id: I2b188a6f5cb202868d43253e706115de570cb1e8
CRs-Fixed: 2162053
Pdev parameter to prioritize IGMP packets are supported through
WMI_PDEV_PARAM_IGMPMLD_AC_OVERRIDE. In legacy platforms, they are
supported by different pdev parameters WMI_PDEV_PARAM_IGMPMLD_OVERRIDE
and WMI_PDEV_PARAM_IGMPMLD_TID.
Map host maintained pdev params wmi_pdev_param_igmpmld_override and
wmi_pdev_param_igmpmld_tid to WMI_PDEV_PARAM_IGMPMLD_AC_OVERRIDE since
this is the one supported by TLV based targets.
Change-Id: Ia11787265bd926f257dc1b028552c6e7f1f733d2
CRs-Fixed: 2272219
Worker thread WMI processing API has more broader use now. So make it
non-static.
CRs-Fixed: 2268243
Change-Id: Iae51e1115f5f3664d08c891e8a42d24bd3ef7bcf
Update the definition of wmi_fatal_condition_event, to include
type+subtype specific data under type_subtype_specific_data.
CRs-Fixed: 2267901
Change-Id: I7f5be6ced26a88ac86ab16efd915a5e6ca5dc608
1. Add support upto 2048 buffers in the ring
2. Add API to print current ring status per module per pdev
3. Start module ID numbering from 0
Change-Id: I7954007c6c486877ffb2ab91724885af2fbaab8c
CRs-Fixed: 2263968
Add host WMI definitions for the type and subtype fields in
wmi_fatal_condition_event.
CRs-Fixed: 2257956
Change-Id: I2c7043081de86a42b3e89ade34d4a1ffc0c39d77
Android Packet Filter 3.0 requires the framework to be able to
read and write into the APF work memory in the Firmware. It
also requires to be able to enable or disable the interpreter.
New WMI commands are defined for read/write/enable/disable
operations.
Complete the implementation of these new commands.
Change-Id: I852d61eb213d9ae530e8a71069144ef35816f5b8
CRs-Fixed: 2184971
wmi_buf_alloc() API expects length to be passed of type
uint16_t. However, the callers pass uint32_t to it.
This might result in overflow and illegal memory access
thereafter. The fix is to modify the API signature accordingly.
Change-Id: If09da4978d421269b884f7d3c933c49c81651475
CRs-Fixed: 2218346
Add service enum and populate service id for listen
interval offload support so that wmi_service_enabled
API can be used to check if the support is enabled.
Add enum for listen interval offload support
Change-Id: I62dbadb4980f54db8431ad53d096f7fc210d25d7
CRs-Fixed: 2253684
QCN7605 requires Management frames to be transported over WMI.
Enable this for HL transport too.
Change-Id: I97551684224cf027beadb403ac2220fa355af986
CRs-Fixed: 2252391
In implementation of Android Packet Filter, functions, variables,
definitions are named after BPF, which stands for Berkely Packet
Filter. The term was more appropriate for Link Layer packet
filters implemented in the Linux kernel, known as Linux Socket
Filters.
The term BPF is obsolete now, so rename it with the
appropriate acronym, APF.
Change-Id: I606afc747cddedb524a41cd8e5998400f04e69f6
CRs-Fixed: 2191531
File wmi_unified_tlv.c is bloated and adding support for upcoming
Android Packet Filter v3 is going to increase its size even more.
Create a new source file for APF related WMI modules and a header
file for declaring the API's
Change-Id: I37dcc30c7d1311067f375c891be9723612161de9
CRs-Fixed: 2189827
Add support to configure logging buffer size from
per-OEM kbuild based on memory requirement.
Change-Id: Ia91d79e5e738b1c9787015de101c3f67ccde46aa
CRs-Fixed: 2253438
