Add support for new ini param RoamScan_InactiveTimer. This param
is similar to the existing roam_scan_period_after_inactivity but
unit change
Change-Id: I0e803decaba30fa3f2dfcd95dc62dc71aa1cb3cd
CRs-Fixed: 3016893
GETROAMSCANCONTROL and SETROAMSCANCONTROL driver commands
will be deprecated from Android 13. So remove all logic
related to these driver commands in the host.
Change-Id: I05fafbec2b3f3b798c8c89d0c33b1dbf5c1b45d4
CRs-Fixed: 3225052
Add cfg item to enable/disable eMLSR mode for ML STA
under 802.11be op mode. The cfg value 0 corresponds
to default MLMR mode, 1 corresponds to eMLSR mode.
Change-Id: Ib02516aac8ac44aee6b40a572a9f7469b10d0ac2
CRs-Fixed: 3184745
Add support for new ini param RoamCU_MonitorTime. This param
is similar to the existing bss_load_sample_time but unit
change
Change-Id: Iae05a9568aa29a5f6a9cfc771e66184e51963ab6
CRs-Fixed: 3015967
With restructuring in hif runtime pm module, modules are
required to register with the hif runtime pm module. Also,
link states are depreciated.
This change registers PM QOS and bus suspend modules which
use runtime PM module and replace link state with resuming
link up state in PMO resume.
Change-Id: I0df48e3d31a1fb0f03faaa0617b48937c9bc224b
CRs-Fixed: 3169425
To support shutdown WLAN when system goes into suspend, add idle shutdown
when got PM_SUSPEND_PREPARE/PM_HIBERNATION_PREPARE.
Before suspend/shutdown, user space should stop adapter. And after resume,
user space should restart adapter. This can ensure user and kernel space
to sync adapter's state.
Change-Id: Id1f5172a7fc1792c83c8c1c20127de815f7e4980
CRs-Fixed: 3208931
When MLO SAP is started with two different bands, the 2.4 GHz
link follows the 5GHz and restarts on the same channel
as 5 GHz link.
The user configured frequency for the SAP is cached on the
psoc, therefore during the concurrency check after bringing
up the second connection, 2.4 GHz link considers the new
user configured frequency of 5GHz link and moves to the same
channel.
Save the user configured frequency per vdev to prevent
cross-utilization.
Change-Id: I62f883bf818332bb7d0c838e6ed629a8f2d2f21b
CRs-Fixed: 3209394
-Wimplicit-fallthrough is being enabled by default. Some compilers
such as clang require the attribute instead of just a fallthrough comment.
Change-Id: If55d68cb76589b39b88d859ea4d9fa6e10246c7e
CRs-Fixed: 3217399
-Wimplicit-fallthrough is being enabled by default. Some compilers
such as clang require the attribute instead of just a fallthrough comment.
Change-Id: I7a04c8727121f58a5d6dcd575446c9acedea164b
CRs-Fixed: 3216248
Currently, vdev in link set active request is added
without any check whether it is ml sta vdev or not
due to which may cause issue of empty event for that
particular vdev when sap/p2p vdev is added instead of
ml sta vdev in request.
Fix is to add ml sta vdev in link set request to avoid
mismatch with fw link down and expected vdev down from
host to avoid empty event failure
Change-Id: If99b305c267f094913b8d9ce96a330eed47d0214
CRs-Fixed: 3221818
set_primary_vdev usecase in STA+STA concurrency is to use that
interface(e.g. wlan0) over the other interface(i.e. wlan1) for
data transfer.
Non-primary vdev use case is to check the quality of that link
and decide if data can be switched to it and make it primary.
It may get disabled if it's not going to become primary STA after
measuring the link quality for sometime or with few APs.
Enable roaming on non-primary vdev also to find better AP.
Change-Id: I3205f1ee1b7da4aa813955308730949ccc70941f
CRs-Fixed: 3219633
Link gets disabled when a secondary STA is connected and if it's
causing MCC with one of the links. Once the secondary STA is
disconnected, this link can be re-enabled.
Change-Id: I5b5f885c103d5fb5611c32422c26112b336c97ec
CRs-Fixed: 3219632
When an ML STA connection exists with more than one link and if
secondary STA connection happened, check if it's causing MCC.
Disable the link that is causing MCC with the new station.
Change-Id: If85da9dd778791c1a5d1a658b97942c5277c5429
CRs-Fixed: 3219631
When an ML STA connection exists with more than one link and if
another STA connection is attempted, allow it. Disable the link
causing MCC with the new station after successful connection.
If there is only one link, reject the second STA connection.
Change-Id: I3cd95e0b425f5e1f96d75f226b058668f030151f
CRs-Fixed: 3218700
Update wiphy->max_num_akms_connect to wiphy->max_num_akm_suites,
based on the upstream kernel change.
Change-Id: I54455b1d3fc162ddea5a0f9380f66a4a06236076
CRs-Fixed: 3214543
Add support for new ini param RoamScan_SecondTimer. This param
is similar to the existing roam_scan_inactivity_time but unit
change
Change-Id: I65c7f88b95d102d9101d8dd59c662650706b247d
CRs-Fixed: 3015947
Add support for new ini param RoamScan_FirstTimer. This param
is similar to the existing gEmptyScanRefreshPeriod but units
change
Change-Id: If250ba41d71ef20c7365af2c90550b3b575d285c
CRs-Fixed: 3016232
The memory allocated for osif_request in wlan_hdd_send_ll_stats_req
is not properly freed and to fix this memory leak, free the memory by
calling osif_request_put() before returning.
Change-Id: I8c60d7d262f7f3ef4a40a1ff272da2516f2d581e
CRs-Fixed: 3220876
Currently, roaming state machine relies on the disconnect
sequence where link vdev gets disconnected first and then
assoc vdev. RSO stop is sent as part of link disconnection
and skipped for assoc vdev disconnection as the roaming
state machine is per ML than per link.
If link vdev connection hasn't happened due to some
reason (e.g. link not available in scan while connect, single link
ML connection), RSO stop command is not sent to firmware due
dependency on above sequence.
Check roam state while processing assoc vdev disconnect and send
RSO stop command to firmware if it's in enabled state to cleanup
the RSO state machine in firmware.
Change-Id: If3e9a579c0f3da27a337fbbffcaf0beb580bd8bd
CRs-Fixed: 3215155
Add support to generate link specific probe response
and add to the scan database.
Change-Id: I30a68df5496bf3e81b4fe71734253555512b82ea
CRs-Fixed: 3158761
Add handling to disable second vdev of mac if miracast
is set for one vdev. In case high throughput or low latency
is required for particular vdev then another vdev on same
mac should be disabled, if present in MCC.
Change-Id: I36cc19f442130b098c4a02ec0ebcf69b89dd2a3c
CRs-Fixed: 3219512
Consider a below case
1. SAP received south bound disconnect command
2. At same time, SAP CSA to DFS channel happened
and thus peers are deleted
3. Later same peer got re-added and south bound
disconnect command becomes active for same peer
When SAP receives south bound disconnect req, then driver will
post WLAN_SER_CMD_WM_STATUS_CHANGE(eWNI_SME_DEAUTH_IND/
eWNI_SME_DISASSOC_IND) command to schedular thread. After posting
to schedular thread, the command will wait in SME message queue.
During this time, SAP CSA to DFS channel happened. Driver will
post CSA to schedular thread and it will wait in PE message
queue.
Since PE message queue has higher priority than SME message queue
CSA will process first. As part of CSA, driver will delete all
peer including sta hash entry.
After CSA, south bound disconnect command got queue to
serialization and same peer got re-added again.
When south bound disconnect command becomes active, the states
will not be proper (as for old peer, disassocTrigger will be
eLIM_PEER_ENTITY_DISASSOC/eLIM_PEER_ENTITY_DEAUTH and for new
peer disassocTrigger will be eLIM_HOST_DISASSOC/eLIM_HOST_DEAUTH)
and thus response to CSR(old peer: eWNI_SME_DISCONNECT_DONE_IND,
new peer: eWNI_SME_DISASSOC_RSP) will not be proper.
Due to this south bound disconnect command will not remove from
active queue which leads to active command timeout.
As part of fix, validate peer before sending to serialization
to avoid queueing the cmd if peer is already deleted.
Change-Id: I099b4b8e85ea8cfd24bcaec0add3c6f1fcaf8b11
CRs-Fixed: 3210877
Enable bits in WMI_INIT command to let the FW know about host's
capability to support notify frame feature. If the feature is enabled,
host can mark certain TX frames as "notify frames" for hardware and they
need not be sent to FW. FW depends on this capability exchange to decide
whether to install HW rules for frames to be sent to HW.
Change-Id: I53b729acc938bc5877de5a872632dd9a2d58845a
CRs-Fixed: 3210693
Add support to handle 2 sap and 1 ml sta link.
Currently, get pcl fails for fourth connection when
2 sap link and 1 ml sta link is present due to which
fourth connection is not allowed as pcl len is becoming 0.
Fix is to add handling for fourth connection when existing
concurrency is P2P/SAP + P2P+SAP + 1 ML STA link.
Change-Id: Ief969018da14096f758fea4bd06d17e7e8d039b7
CRs-Fixed: 3219328
Currently in driver, NAN Data Interface can be created with
only name "aware_data" which creates dependency on interface name.
To remove the dependency, the interface is created now by name
provided by Wifi-HAL.
For this, interface is created in STA mode with name provided by
WiFi-HAl. While processing vendor cmd QCA_NL80211_VENDOR_SUBCMD_NDP,
given ifname is searched in adapter list and mode is changed to NDI.
CRs-Fixed: 3196179
Change-Id: I62dd512f8a7de4c69a53babf3112942d348bf3b6
