Add only wmi_roam_scan_mode_fixed_param TLV for ROAM_SCAN_MODE disable
command[i.e. mode is set with WMI_ROAM_SCAN_MODE_NONE |
WMI_ROAM_SCAN_MODE_ROAMOFFLOAD]. This is to retain the scan params
[n_probes, dwell time] so that it can be used if ROAM_INVOKE command
follows ROAM_SCAN_MODE disable.
Change-Id: Iafe31850872cac3eaff35eeb57ab271b4409ef18
CRs-Fixed: 1084912
Analysis: strict passive scan is not working as the scan_ctrl_flags
check is missed when strict passive scan enabled
Change-Details : Added a support in ol_ath_scan_start_send() and
send_scan_start_cmd_non_tlv() to update the scan_ctrl_flags with
WMI_SCAN_FLAG_STRICT_PASSIVE_ON_PCHN when strict_pscan_enabled
Change-Id: If6713e340841d4947ef9042421dabec35f7bfbae
CRs-fixed: 1069383
For Beeliner family of chipsets, the number of values expected is 688
for 2G and 1540 for 5G
Change-Id: I2c47ed98f639c09453687fce7f713946304a7036
CRs-fixed: 1071083
WMI command buffer is not cleared after WMI command TX completion.
For DISA certification TK and GTK should not remain in the memory
area after disconnection. Since WMI command buffer is not cleared,
hence content of TK and GTK is still in host memory region.
Clear WMI cmd buffer after TX completion.
Propagation from qcacld-2.0 to qcacmn.
Change-Id: Ib09a77b630c932409645b7a989bd959f0ed4f514
CRs-Fixed: 1060982
Log Transport Layer Tag for debugging. The tag differs for
normal command and the runtime pm commands.
CRs-Fixed: 1072520
Change-Id: I7ec085410aaa429cfeb8cc09729e62deee9c7d95
Recently added changes for coexistence of WIN/MCL TLV implementation
through CL I6868c288a43fd3afb19c84b8a9d4ef0dfbee5c94 require
adaptations in QCA WIN driver to successfully compile.
Add required definitions in WMI layer to adapt WIN driver to
changes made for coexistence.
Change-Id: I99550ca10553d8096b8967249c006bac4e0c62df
Currently, RTT related operations to change report type and number
of measurements are done in the WMI layer.
Abstract these operations out of WMI layer and keep it in the WIN
host API layer to make the RTT WMI API generic.
Change-Id: I9b73830912c6c2b3d0908788f1f6a77b7f43dcaa
TxRx chainmask is populated by the FW only in the case when report
type is WMI_RTT_REPORT_CFR.
Populate txrx chainmask to 0 when RTT report type is non-CFR to avoid
corruption.
Change-Id: Ie728656efe2f608e90a15b6fc94be3159db0f635
CRs-Fixed: 1080686
LOWI messages to register, set capability
and send RTT measurement request are not sent assuming only
LCI and LCR messages are sent out to the FW using ol_ath_lowi_data_req_to_fw.
Add code to send messages other than LCI and LCR through the API in
ol_if_lowi.c when msg subtype is not one of LCI or LCR.
Change-Id: I2deedaa6e03e769bf802337b2ec93d9573eb1b5a
CRs-Fixed: 1079169
The packet is allocated in wmi_unified_cmd_send so if it doesn't
get sent or added to a queue it needs to be freed.
Change-Id: I763824812d3c0510c53a70caf063568385b9bfc2
CRs-Fixed: 1079509
WMI_RECORDING:Fix implementation of WMI_MGMT_COMMAND_RECORD to
be compatible to WIN.
Current implemantation uses variables not applicable to
WIN.
CRs-Fixed: 1067944
Change-Id: I65b2415e40bd888d3b94ef5f04ec6d53b4d50da2
Tx data capture feature needs a new WMI command.
The fw common file is already reflecting this new
command.
New enum is added to WMI_HOST_PKTLOG_EVENT for this
feature.
Change-Id: I7b8535a311033debbbee5f56c87ac4858a0aa8e1
CRs-Fixed: 1068402
Acked-by: Debasis Das <ddas@codeaurora.org>
qcacld-2.0 to qcacmn propagation
Make the following enhancements to the EPNO feature:
1) Implement the reset EPNO command handler
2) Add new parameters for candidate score calculation.
Change-Id: Iad1ff9c2b003c9e3ddbc3373366686040ccb55ca
CRs-Fixed: 1075380
Extraction API for phy error event handling does not populate single phyerr
RSSI info for DFS radar event, but was populating the value in case of
spectral event. Single phyerr RSSI info is required for both DFS and Spectral
operations. As a result of this change, single phyerr RSSI info is updated
on receiving DFS event as well.
Change-Id: Idca3e4075e1869eda0d200a102e2ca2b7d33bf70
CRs-Fixed: 1076872
qcacld-2.0 to qcacmn propagation
gscan priority should not cross normal scan.
Add changes to reduce gscan priority.
CRs-Fixed: 1066785
Change-Id: I7459367cfed5d932f07f8c846265c448b9a84555
Propagation from qcacld-2.0 to qcacld-3.0
Some of the logs are printing quite often and spamming the kernel logs.
Hence move them to appropriate log levels and remove the useless debug
messages.
Change-Id: If38d7a6a3cf13a5879f6a628d3d7eb4f5156a95b
CRs-Fixed: 1001441
A_OK status is deprecated. Use QDF_STATUS_SUCCESS. Needed since
wmi_unified_cmd_send returns QDF_STATUS not A_STATUS.
see change: Ib9b0a60976dedcf8fcd4184083a9948892791621
Change-Id: I91209002c0a84a8353541c84cdc2e49ffdcc6654
CRs-Fixed: 1072077
If param->len was 0, ret would be returned without being initialized.
param->len of 0 is unexpected, so return an error.
Change-Id: Ib9b0a60976dedcf8fcd4184083a9948892791621
CRs-Fixed: 1072077
Green AP feature for WIN allows the AP to go into power save mode
and leads to only a single chain being active.
In the current code, it is seen that the WMI API for enabling Green
AP feature is under "FEATURE_GREEN_AP" flag that is not defined for
WIN. This leads to trigger of dummy API that does no operation.
Replace "FEATURE_GREEN_AP" with proper flag "ATH_SUPPORT_GREEN_AP"
defined on WIN to enable Green AP feature.
Change-Id: I344e74c3753f1ef3b6d5d5a2bb1086c84f2ab84c
CRs-Fixed: 1074036
Add TLV changes to pass DISA parameters received from
WMA and pass them to firmware for firmware
to encrypt data and send back to driver.
Change-Id: Ic6928a93f799c47518fbbad96564062f595287dd
CRs-Fixed: 1072545
On issuing iwpriv wifiX dl_loglevel <Val> command, there is a NULL pointer
dereference crash observed. It is root caused due to improper reference
to module_id_bitmap field, that needs to be corrected.
Change-Id: I59ff4455c74452bb00caff125f84213a2e9d7742
CRs-Fixed: 1066323
Fix following issues in wmi_unified_non_tlv.c file
->Move allocation of WMI buffer in FIPS WMI cmd
->Change dummymask variable to static in mcast_group_update cmd
Change-Id: I0a0d0e68820905ad543175abed1a812639b3dbf1
CRs-Fixed: 1069863
For big endian based offload radios, key installed using
WMI_VDEV_INSTALL_KEY_CMDID requires to be code swapped as the copy engine
for big endian platform does byte swap operation on the received key before
sending it down to FW.
It is observed that the big endian conversion is carried out in WIN Wi-Fi driver
for big endian platform specific radios in the driver, that takes care of
converting the key data to the byte swapped form. However, it is observed
that an additional copy is carried out in the WMI layer that is overwriting
the converted key with old key, in the non-swapped form.
We move the byte swapping operation to the converged component and do a single
memory copy using the macro that carries out its operation based on big or
little endian platform.
Change-Id: Ic6b7cc667d0f505d1d1daeacec72f54d41554038
CRs-Fixed: 1067206
Extraction API for phy error event handling does not populate composite
RSSI info for DFS radar event, but was populating the value in case of
spectral event. Composite RSSI info is required for both DFS and Spectral
operations. As a result of this change, composite RSSI info is updated
on receiving DFS event as well.
Change-Id: Ia77779251ccf230f7ca4242ee0851790305d2fbc
CRs-Fixed: 1066136
qcacld-2.0 to qcacld-3.0 propagation
Enable firmware to send WMI_EXTSCAN_CYCLE_STARTED_EVENT and
WMI_EXTSCAN_CYCLE_COMPLETED_EVENT instead of
WMI_EXTSCAN_BUCKET_COMPLETED_EVENT as per Android N requirements.
This change is required to complete the propagation of
earlier change I399204261fa3d8515146c590630a3bb663ee801c
CRs-Fixed: 1062739
Change-Id: I5c801912828844aa3d8e2aa4f022cb184aa771c4
Non-TLV registrations for atf_peer, atf_group and lcr WMI command were
missed out during the WMI convergence implementation. This change adds
the missed out registrations.
Change-Id: I384c27709e088c06ee73f17b7dc1a52bb5c63370
CRs-Fixed: 1069863
PEER assoc command failed in the tlv validation check.
Tlv length sent in the TLV header is different from
the length used to fill the tlv buffer which caused
failure at tlv validation.
Modified code to use the aligned length while
filling the tlv buffer.
Change-Id: I9ad2009315dd3cf37308ef44360d566035344950
CRs-Fixed: 1069008
qcacld-2.0 to qcacmn propagation
As Current WMI interface need both the ARP/NS configuration
in single command. To support active offload host need to
cache the ARP/NS at wma layer so host can fill the other
request and configure down to firmware complete request
(ARP+NS).
Change-Id: Ie0a57d216379817ff0ae48f4f582c9108e8ecca1
CRs-Fixed: 1067683
These fixes are made during qca8074 VP control path bringup.
Add fixes in tlv.c and enable TLV helper routines for WIN.
Fixed some inconsistencies in wmi API params by adding compiler flags.
This needs to be cleaned up so that API and params have common interface
between WIN and MCL.
Change-Id: I0821daa58df86ad0b394a7846a982a9e3577cd14
CRs-Fixed: 1063252
Address compilation issues for WIN with new Lithium Firmware headers.
Also removed dependency on htt.h from header files, which may need to
add explicit dependency on htt.h in .c files.
Change-Id: Ia5027963837e645bc3f81a3db98c2ea06789aea8
CRs-Fixed: 1061096
Propagation from qcacld-2.0 to qcacmn.
Add support to get per chain rssi from fw through the
already existing WMI command WMI_REQUEST_STATS_CMDID
and then store it in the station_info structure defined
by cfg80211.
Change-Id: Id50c96dd322b5ca4db34cf2df901730d8b103251
CRs-Fixed: 1005367
Send HT/VHT CAPs IE to firmware per band. This will allow certain
features like LDPC to be configured per band.
Change-Id: I21c83af984f9be3ade46121ef148b52568c3ad0f
CRs-Fixed: 1059454
As part of MBO(MultiBand Operations), host driver need to supply
the default scan IEs to firmware at wifi init time using existing
VDEV SET IE command. FW uses these Scan IE's in subsequent scans
.i.e. FW initiated Probe Requests.
This Fix updates the vdev_ie_info_param struct with ie_source.
ie_source will be set with zero for VDEV SET IE commands from
host driver
Change-Id: Ie2e87da8aa94b76aef431e25d9974b8fed63eba9
CRs-Fixed: 1039969
qcacld-2.0 to qcacmn propagation
In some cases wmi_buf_alloc is used to allocate memory, while
adf_os_mem_free(vos_mem_free) is used to free the memory.
vos_mem_free checks if memory is present in vosMemList to detect
double free.
Now as wmi_buf_alloc doesnot add the allocated memory to
vosMemList, vos_mem_free assume it to be double free case and cause
kernel panic.
Use proper corresponding API to free memory
Change-Id: I3602887d2bfdb407e5805aedd7a97a57440a4567
CRs-Fixed: 1004079
Enable or disable OKC flag in WMI roam scan offload request based on
okc_enabled parameter in roam request from CSR.
Change-Id: I19ad7ea2171532f2417742e205d408bdd52682c0
CRs-Fixed: 1057181
The qdf_mem_set API is used incorrectly in a few instances inside
wmi_unified_non_tlv.c
The argument list is - <pointer to address, size, value>
However, some places, it is sent as - <pointer to addr, value, size>
This change fixes such incorrect function calls to qdf_mem_set().
Change-Id: Id50136f630022b1fdeaddbdefcad9f637f917e9e
CRs-Fixed: 1048504
WMI HB command buffer is not freed in case of tx error,
Free WMI HB command buffer in case of errors.
Propagation from qcacld-2.0 to qcacmn.
Change-Id: I15577c50cefc0cc2e9129f175cf874f17acc430e
CRs-Fixed: 1001068
This change implements the Non-TLV WMI API for setting bandwidth
fairness. This WMI command was implemented as part of the recent WIN SW
release. This change ensures it is adapted to convergence code structure.
Change-Id: Ib9984c43b91b105bfb4687a7591f4fab509febc4
CRs-Fixed: 1060577
This change fixes the compilation issues faced due to WMI convergence
changes on the big endian platform.
Change-Id: I18bae4fb7884683d8621ce9a862dc1a51ef84f82
CRs-Fixed: 1039318
Propagation from qcacld-2.0 to qcacld-3.0
Current implementation has support for IPv6 addresses of type
unicast for NS offload to firmware.
As part of this change add anycast addresses for NS offload.
CRs-Fixed: 954880
As part of MBO(Multiband Operations), host driver need to supply
the Assoc IEs to FW after initial connection. FW uses these Assoc
IE's in subsequent roaming.i.e Reassociation requests.
This Fix updates the WMI interface to provide support for passing
Assoc IEs to FW.
Change-Id: Ida3d2947714002233090a3f9075dd8d674a3c224
CRs-Fixed: 1039969
Add changes to allow coexistence of WIN/ MCL TLV implementation
through use of CONFIG_MCL flag and change of MACRO names.
Change-Id: I6868c288a43fd3afb19c84b8a9d4ef0dfbee5c94
Acked-by: prgandhi@qti.qualcomm.com
CRs-Fixed: 1008872
