Cast returned u16 value to int in VA/TX macro: clk_div_get
to avoid possible data type warnings seen in function
caller.
Change-Id: I08943a26294ce54a207b739867292c01d090623e
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Interrupt from wsa883x are not handled as slave_irq is not set.
Add slave_irq for wsa883x to address this issue.
(cherry-picked from commit ddfc43e7c48dcbe9bbae45b5caacdd5bca441800)
Change-Id: I6b56aa88cca895e4e0e5871a7478f6859d45b03f
Signed-off-by: Phani Kumar Uppalapati <quic_phaniu@quicinc.com>
regmap_irq_chip->irq_drv_data is shared by all attached wsa
devices and point to last probbed wsa device. This will cause
interrupt handle issue. Update irq_drv_data per wsa deviece to
resolve this issue.
(cherry-picked from commit 1852682fbcebfb9f479c3d09a91c075049b90253)
Change-Id: I6ac0520a4074d74dfb28122e06eed6a86374c0ce
Signed-off-by: Phani Kumar Uppalapati <quic_phaniu@quicinc.com>
PA_ERR can happen during speaker path setup. Log the
error status in the interrupt handler and clear the error
status for next audio playback to resume properly on
the speaker.
Change-Id: I0490d4cdd6379ed779ce7f54ec8b56d5a7af0649
Signed-off-by: Phani Kumar Uppalapati<quic_phaniu@quicinc.com>
Update to 5.15 kernel dapm api.
Pin name no longer needs prefix as it is added in API.
Change-Id: Ibf967dd01a36decdf904eff9d5af2e315aa53f1c
Signed-off-by: Kunlei Zhang <quic_kunleiz@quicinc.com>
Only UVLO_irq, PA_ON_ERR_IRQ and PDM_WD_IRQ are enabled
on wsa883x. Enable all other IRQs to monitor if WSA is in
bad state.
Change-Id: Ia78f12520eda4b26c00776583a78b14b74771e0e
Signed-off-by: Meng Wang <quic_mengw@quicinc.com>
With current setting for VBAT_ATTN1/2/3, pop is heard when
battery is low. Update default value for these registers
to resolve pop issue.
Change-Id: Ic4002a4b30ecd04b04001ca5f16bac5745a803d7
Signed-off-by: Meng Wang <quic_mengw@quicinc.com>
Can now set these registers during init once these values are
acquired.
Method called again before playback in case there are
speaker/recv changes.
Change-Id: I1b544633a660e98acadf94b9589b7656edebdd56
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Update mode argument type from int to u32 to avoid
any potential data loss since input is also u32 type.
Change-Id: I9541a7da20d2a22a0066622736268adffde5adbf
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Whenever there is an interrupt,
mute the PA, then wait 1ms and unmute the pa and
check for another interrupt. Then if there are still interrupts,
retry muting and unmuting the pa with delay.
If interrupts persist, the PA will remain muted until there is a
usecase teardown or reset.
Change-Id: Ic59fc33d4606c1c630a61796d513a9ec99a4979c
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Update to latest sequence from WSA hardware systems team.
Add writes for VADC, BG, Boost
Change-Id: Ic61e1c36154ff673fce05546332e89fe683a3075
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Add new lpass RX paths. Needed to fix
WSA ADIE Loopback.
Update DAPM enum length to include these RXs.
Change-Id: Ie174cfab20b8beb103eefa94636e76ad756c7345
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Add to avoid crashing related to device tree parsing
of SWR port params.
Change-Id: Id839cc908fb5f7843e5fd6260b3205c8844349ba
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Found potential issues relating to uninitialized or out-of-bounds variables
present in codec drivers. Place checks to ensure proper ranges are used.
Change-Id: Ib68cba2413788a57237f1f18fc5ce5fb5c6bfb0a
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
For PBR and CPS ports, need the ability to customized slave
SWR frame OFFSET1 settings. Add similar method to WCD TX where
offset1 and lane_ctrl parameters are parsed from WSA device tree
and configured in SWRM.
Change-Id: Ib973ed93d9daa5ba02461a156e5b0a8c816d371e
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Update to 5.15 kernel dapm api.
Pin name no longer needs prefix as it is added in API.
Change-Id: I5c1378839f4c4d2aa70fb11706c5bb65d4eb0952
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Update function to correctly read array from device tree.
Previously not reading values and returning -EINVAL.
WSA bat_cfg/rload/sys_gain are now correctly configured.
Also add softclip clock enable during pbr config.
Change-Id: Ia1b93acfde3e799b3b72e05966d0fa955c3f49ac
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Removed PA Mute, COMP Offset, Ext_vdd as they will not be used
in WSA884x.
Change-Id: I58ffd490c9929fa3388678d9ab7114207779191d
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Add idle detect source select based on NG mode,
if NG2 then source is PRE-LA else LEGACY
Change-Id: I4e0cb3825960e6b795038fb5e85cfaa7a2fbfe62
Signed-off-by: Shazmaan Ali <quic_shazmaan@quicinc.com>
Add idle detect enable for mixed control path,
and update copyright markings
Change-Id: Idf2932cd1813082f60ee96010788cdb1ef36afbf
Signed-off-by: Shazmaan Ali <quic_shazmaan@quicinc.com>
Add set config function to validate and
set battery stack mode, rload and system gain
Change-Id: I075bf3cde6a9671a8d93f32aec43b941ea86f2ea
Signed-off-by: Shazmaan Ali <quic_shazmaan@quicinc.com>
Read noise gate mode from device tree,
set NG2 based on the register read or
set to idle detect mode
Change-Id: Id1e478ad230125d1e35229493cb0fbd6867c6a3b
Signed-off-by: Shazmaan Ali <quic_shazmaan@quicinc.com>
Boost current limit is now dependent on PBR and bat_cfg.
Add BOP2 VTH/HST initial settings.
Add OCP LOW VBAT ITH sel settings dependent on bat_cfg.
Change-Id: I235f4b75ee12e5f24d46fa0ebca67547997934e2
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Add PBR/CPS ports to debugging by adding logic to
is_swr_slave_reg_readable.
Change-Id: I9ef09ed90ccce2c696eaec7b1eed9c47a7e73f58
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Lpass-side enablement of new WSA feature.
Configure PBR registers based on WSA bat_cfg/rload/sys_gain.
Some registers updated during init, others during enable_interpolator.
Change-Id: Iac42672182827a9da47700319c61b9d0a17d0936
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Change PBR enable to be acquired from device tree.
Using system_gain, bat_cfg, rload, set pbr thresholds based on tables.
Table values are x100 to avoid kernel float issues,
truncate when converting to reg val.
Set pbr registers during initialization.
Rename WSA_8OHMS -> WSA_8_OHMS to match system gain naming.
Change-Id: I28985496e1da37ceeb8c9db6e17f4c48d37d11c7
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Previously we disabled all irqs by default and toggled them pre/post
playback. Update to leave them enabled by default and remove the toggling.
Also, leave the default values for edge/level triggering.
Change-Id: Iac96649fc0f33cbdf5a25f136cf577f7242db74e
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
If not using compander, allow for user to set pa gain
using DRE_CTL_1 register.
Change-Id: I45af5a64a5630ff1cd8410a66ed55914efb5a529
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Update WSA rload, system gain, bat_cfg to get from wsa_macro device tree.
WSA Bat_cfg change to read from VPHX_SYS_EN_STATUS reg.
Add device tree parsing for these params in WSA macro
and WSA driver.
Remove machine driver method of sending the parameters.
Add default_dev_mode (spkr vs rcv) from device tree for WSA.
Move code from spkr event to userspace controls or probe.
Change system_gain and affected params when switching between
dev_modes.
These changes simplify configuration data and code and allow
more registers to be written during bootup or before playback.
Change-Id: I79966c704adfac1bf2d85aa6519ea574764c7a8b
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
PA_ERR can happen during speaker path setup. Log the
error status in the interrupt handler and clear the error
status for next audio playback to resume properly on
the speaker.
Change-Id: I5800d9505a3036127097745aaa880b73b3e87f30
Signed-off-by: Sudheer Papothi <spapothi@codeaurora.org>
Signed-off-by: Meng Wang <quic_mengw@quicinc.com>
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Udpate MSM DMIC power up sequence to reduce pop.
Change-Id: I5f3f2e439e31877d3f21c05575c95942b937252e
Signed-off-by: Meng Wang <quic_mengw@quicinc.com>
Fix isense/vsense gain tables to correct values.
Mark ana_wo_ctl registers as volatile.
Move VBAT_THRM_FLT_CTL to init reg sequence.
Change-Id: Ie04f302719f08b35f1ef9807dff7993c31e3aa43
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Add PBR, CPS port types and port parameters for WSA
Update RX and TX port types to include full list of ports
Change-Id: I5b69ee777addebcf4167dccd4ce4ab0af31b754d
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
regmap_irq_chip->irq_drv_data is shared by all attached wsa
devices and point to last probbed wsa device. This will cause
interrupt handle issue. Update irq_drv_data per wsa deviece to
resolve this issue.
Change-Id: I013f546d7f1ca6077f0b14e875b135a27325f851
Signed-off-by: Meng Wang <quic_mengw@quicinc.com>
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
during devm_snd_soc_register_card(), the name_prefix can be set
if "sound-name-prefix" is provided in the DT nodes.
The original approach to set prefix would possibly cause ASoC
component probe failed if prefix has not set before probe is called
Change-Id: Ie78d042cda24b7d1d926223d476786e13d965ac7
Signed-off-by: Junkai Cai <quic_junkai@quicinc.com>
Interrupt from wsa884x are not handle as slave_irq is not set.
Add slave_irq for wsa884x to address this issue.
Change-Id: I82edb35b55f6a46d79bd96b7f0f4bfac58583860
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
When interrupts are triggered on the second or third interrupt
status register, current logic cannot clear that interrupt status
after handling it. Enable use_single_read for wsa and wcd regmap
to resolve the issue.
Change-Id: Ieac57e169505d4455dde1dcd0e80e222e3e8eb1e
Signed-off-by: Meng Wang <quic_mengw@quicinc.com>
Conforms to latest hardware DRE documentation
Change-Id: Ia08b03f519697723e9e260451c5bc68b4b45724c
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
