Add support for new ini param RoamCommon_MinRoamDelta. This param
is similar to the existing min_roam_score_delta param but units
change
Change-Id: If04ff2344a2651e7d8d71c92f05dfebc229f9fe1
CRs-Fixed: 3015930
Add support for new ini param RoamIdle_InactiveTime. This param
is similar to the existing idle_roam_inactive_time but unit
change
Change-Id: I857107a6d0e39f373e39d4fb9b762e7cf4c4a9e4
CRs-Fixed: 3015993
i.) Keep rf test mode ini disabled by default due to which
6G security check will be true.
ii.) while calculating TPC power, check safe mode & RF test
mode enabled or not and set power mode to LPI if
safe mode or Rf test mode is enabled.
iii.) During HE ops IE extarct set power type to VLP, if
6 G Hz info is not present in HE ops IE. So that power
type can be VLP in case ap_ctry is non US.
To get safe mode value, a new member is_safe_mode_enabled
is added in mlme private object and is set whenever
WIFI_TEST_CONFIG_6GHZ_SECURITY_TEST_MODE command is triggered
via userspace.
Change-Id: I4fc2a231f8e7d18e68b92af3f381456113668779
CRs-Fixed: 3192967
Currently we are reading early stop scan min and max
threshold to unsigned int, because of which we are
sending wrong values to FW.
Read early stop scan threshold min and max values
to signed int to send correct values to FW.
Change-Id: I2e96b3c3e9fb48352d8075a4e7a96eae41dacedc
CRs-Fixed: 3191076
Move wlan_mlme_get_wlm_multi_client_ll_caps API to dispatcher
folder so that other components would use this API to get
the multi-client feature capability flag.
Change-Id: Ib247401b9411c40a838b338a60d44cb187884480
CRs-Fixed: 3181381
The current maximum buffer size for an ADDBA response action frame is
256 bytes. This needs to be increased in case of EHT session.
Change-Id: I4e4dbe1dbe5c69954d26f73cf51177358c411083
CRs-Fixed: 3185336
Based on the ini "sta_sap_scc_on_indoor_chan" the behavior of
STA+SAP in scc is as follows:
1. STA is on 2.4 GHz & SAP is on 2.4 GHz and SAP user configured
initial channel was on 5 GHz, then move SAP to 5 GHz initially
started channel
2. When STA + SAP are doing SCC on indoor only channel and
a) STA moves to 2.4 GHz -> then SAP moves to initialy started
channel
b) STA moves to another indoor only channel -> SAP follows
STA channel
c) STA moves to non-indoor, non-dfs channel -> SAP follows
STA channel.
d) STA moves to DFS channel -> SAP moves to 2.4 GHz channel
e) STA disconnects -> Move SAP to initially started channel
3. STA is on 2.4 GHz & SAP is on 5 GHz non-indoor, non-dfs channel
and STA moves to 5 GHz channel, then SAP should follow STA to 5 GHz
if SAP was initially started on 5 GHz channel. Else SAP restart
is not required and SAP will remain on the 2.4 GHz channel
Change-Id: I655dffff026d8147e13599dddc024980ba157be5
CRs-Fixed: 3186965
Currently req->ctx.cb_arg is assigned req memory
in wlan_mlo_sta_mlo_concurency_set_link. and passed to
mlo_ser_set_link_req, where req is again alocated
and req pointer of req->ctx.cb_arg is freed, thus
making req->ctx.cb_arg invalid.
Fix is to avoid allocation of req again and use the
requester memory of mlo_ser_set_link_req as umac_cmd.
Change-Id: Ic96efa204662269fe812c195a3bc8a1da5b215ad
CRs-Fixed: 3188737
Currently mlme_set_twt_peer_capabilities() api is use to
update twt capabilities using he caps and he ops. But now
onwards partial TWT(requestor and responder) can be
supported from 11n mode also.
Make this api as generic so that it can be use for both
11ax and 11n.
Change-Id: Id89e056927a914938efad7116796cbf64b5764db
CRs-Fixed: 3185133
Currently driver does not caches peer nss and it needs this info
for big data stats. When driver receives big data stats command
it always returns nss as 0 which is not correct.
To address above issue, add support to cache peer nss in SAP
mode.
Change-Id: I5152581d7d66b5bf20f6102dcb9edaa4e23b35bc
CRs-Fixed: 3174420
Issue scenario, 1st Addba response tx and set is_mgmt_data_valid false.
2nd TX frame happens for valid frame that needs to be logged and set
wma_handle->is_mgmt_data_valid to true. Then the 1st frame TX completion
tried to access wma_handle->mgmt._data. It may access invalid context if
race condition happened.
Move management frames handling from lim_send API to tx_complete_cnf API
Change-Id: Ib5090dcd274160b3a9d7b9975d0839ec06616b86
CRs-Fixed: 3154710
SAE authentication logging events are sent from host
driver during connection as well as during roaming.
But the other roaming frame related stats are printed
as part of the WMI_ROAM_STATS_EVENTID handling.
Since this roam stats event is received after preauth
frame related logs are queued to userspace, the order
of the logs are not correct.
Cache the SAE preauth logs in mlme and print them
upon receiving ROAM stats event. Read the firmware
service capability to decide if new caching needs
to be used or legacy behavior needs to be followed
Change-Id: I76381b9deef222f1481325974e2b5d9730eb2b67
CRs-Fixed: 3154147
Add multi-client latency level service bit capability support,
WLAN_SOC_WLM_MULTI_CLIENT_LL_SUPPORT, to check whether the FW
supports multi-client latency level event or not.
Add INI "wlm_multi_client_ll feature" to enable/disable multi
client latency level feature from the host side.
* @min: 0
* @max: 1
* @default: 0
If firmware sends multi-client latency level service
bit capability to host and host enables multi-client latency
level feature via INI, the host waits for an event
WMI_VDEV_LATENCY_LEVEL_EVENTID as a response to a request
command WMI_WLM_CONFIG_CMDID.
Change-Id: I5cbea89e67caabac5db70b7f0a91c18bdd512e9b
CRs-Fixed: 3180928
Add support to dump the full management,eapol,
dhcp, arp frames based on the level of the
debug_packet_log configured through ini gEnableDebugLog.
The dump levels are as follows:
* 0x1 - Enable mgmt pkt logs (except probe req/rsp, beacons).
* 0x2 - Enable EAPOL pkt logs.
* 0x4 - Enable DHCP pkt logs.
* 0x8 - Enable mgmt action frames logs.
* 0x10 - Enable ARP pkt logs.
* 0x0 - Disable all the above connection related logs.
Change-Id: If572cccb327da785dd0d56cff6d37ba170b15cc8
CRs-Fixed: 3173604
Add a new field max_mcs_index in mlme_legacy_priv to save max mcs
index of current vdev.
Add a new field max_real_mcs_idx in hdd_station_info to save max
mcs index of the connected station.
Change-Id: I28908515cbe5c18c79f14f8645defd5c82e3a6f0
CRs-Fixed: 3065838
Since HB failed logic change to send deauth, we don't
need probe logic after HB failed. Clean up timer and
unnecessary code.
Change-Id: I26d9235c157065a21469b01abf31751825a1f277
CRs-Fixed: 3158364
Generate a Level 2 update frame and send it to the bridge in SAP
mode when a new station connects.
It will update the forwarding table of all the bridge devices
through source port learning.
Change-Id: Ia804968453c051e4c8322d3735506a912c0d963d
CRs-Fixed: 2997409
Reduce the log level for the frequent acceptable errors
to reduce the roam latencies.
Change-Id: I9f5405025948d160e6fcd65ecca05dce7670ea84
CRs-Fixed: 3150439
Move MLO STA-SAP concurreny handling to Policy Mgr which
is present in CSR currently.
Also, Move MLO STA-STA concurreny handling to Policy Mgr
which was part of If Mgr currently.
Change-Id: I2b8de17c3d31b43ff1f6b81a7de07b88888d7fb5
CRs-Fixed: 3153393
Peer MAC address is not specified when get_peer_by_mac fails.
We should print the peer MAC address with debug message.
Change-Id: I9d75098784879ddecd447f8dbbcd61e6cdc1bf76
CRs-Fixed: 3153776
Add new config to ease scan and connection restriction
in 6GHz band when bss is advertising different country.
Change-Id: I13bd0dbd52fad297b995add8fc8a71d7a058c25b
CRs-Fixed: 3135152
Replace blacklist/whitelist with denylist/allowlist in
qcacld3.0. and replace blm with dlm.
Change-Id: I9ba61dde3b3ea008ca3777448d1f8dab83d33ec1
CRs-Fixed: 3091211
During CSA max bw is selected for SAP in STA + SAP concurrency
for non-dfs channel and SAP is tear down after 60 sec of operation
due to STA is in 20Mhz and SAP is in 40Mhz with
IEEE80211_HT_CAP_SUP_WIDTH_20_40 flag disabled.
This change is to select 20Mhz BW during CSA if channel bonding is
disabled.
Change-Id: If4ed3d9a080ed976a0f4be6704848ae4494c7bbc
CRs-Fixed: 3126074
Update LFR2 self reassoc failure processing:
1. remove lim_send_switch_chnl_params() from
lim_restore_pre_reassoc_state() when self reassoc failure
to avoid this race condition: one one hand host let FW do
restart, and on the other hand VDEV sm transition to stop
state. Otherwise VDEV sm cannot handle EV_START_RESP event
correcly.
2. register .mlme_vdev_sta_disconn_start callback with
cleanupTrigger eLIM_HOST_DISASSOC.
3. when self reassoc fail, notify reassoc failure reason
to CM SM so that CM SM can trigger CM_DISCONNECT_REQ, then
invoke .mlme_vdev_sta_disconn_start doing cleanup action.
Change-Id: Icb68202e9f72fcbe3e0e4d3e9006a65a73123692
CRs-Fixed: 3109987
Firmware doesn't expect any vdev commands from host while RSO stop
is happening. It sends a response to the RSO_STOP command once
it's done with cleanup. Host needs to run a timer after sending
RSO stop command to firmware and wait for a maximum of 6 seconds
for the response. Host can stop the timer and allow the commands
to firmware in the below cases,
1. RSO_STOP response with success status
2. RSO_STOP response with HO_FAIL status followed by
HO_FAIL event: Host needs to wait till HO_FAIL event is received
If firmware doesn't send any response in the 6 seconds wait, issue
a recovery to help to check the firmware state.
Also, set WMI_ROAM_SCAN_MODE_FLAG_REPORT_STATUS always when MLO is
supported while sending RSO_STOP to firmware. It's sent only
in case of wpa_supplicant disabled roaming currently.
Change-Id: I8182e60beb9288dba23cc72e978dc781c8ab1707
CRs-Fixed: 3106023
Currently moderate latency level is not used. Rename moderate
latency level to XR latency level to be used in XR applications.
Change-Id: Ia7f65c3565f6704b9571161aabefb3a8b47cce1e
CRs-Fixed: 3116839
Currently regulatory channels are disabled for
QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY_EXT vendor command
event if ini coex_unsafe_chan_nb_user_prefer is not set and if
STA operates on disabled channels which results in crash for
STA interface in STA + SAP SCC case.
Hence coex_unsafe_chan_reg_disable ini is controlled based
on coex_unsafe_chan_nb_user_prefer.
Ini behavior summary:
|----------------|----------------------|-------------|--------------------------------|
|User prefer ini | Reg chan disable ini | PLs | Expectation |
| | | | |
|----------------|----------------------|-------------|--------------------------------|
| 1 | 1 | LE | accept freq ext command and |
| | | | disable the regulatory channel|
|----------------|----------------------|-------------|--------------------------------|
| 0 | 0 | Non-Pixel SP| reject freq ext cmd driver and |
| | | | returns NOT SUPP |
|----------------|----------------------|-------------|--------------------------------|
| 1 | 0 | Pixel SP | accept freq ext command and |
| | | | Don't disable the reg channels|
|----------------|----------------------|-------------|--------------------------------|
Change-Id: Ia3acbc133cab4865d8ad69992e893be91439f856
CRs-Fixed: 3128908
Before MLO sta partner link is up, FW can't indicate CSA event to host.
For this case, host need save csa parameters and process it when MLO
sta partner link is up.
Change-Id: I543c5e1069af5b1e88c6619364a7a44330134d2c
CRs-Fixed: 3082437
Currently, for Broadcast TWT setup command, if peer does not
support TWT responder capability and supports broadcast TWT
capability then host rejects broadcast twt setup command
based on TWT responder capability.
Add condition to check the peer broadcast capabilities before
sending broadcast TWT setup request to firmware.
Change-Id: Iaa8941424d948d501655859564669baff4af9e69
CRs-Fixed: 3092276
Update latency flags inis to 64-bit configuration and use
lower 32-bit for firmware configuration and upper 32-bit
as host configuration. Also remove separate inis for host
latency flags.
Change-Id: Iff62b847f40ae7fa5f82948ec37d756144860474
CRs-Fixed: 3115853
TWT initialisation will fail for each non 11ax connection
so an error log is not needed if peer object for TWT is not found.
Also, RIC data is not mandatory in FT session, so if its not
present, log a debug level print instead of error level.
Change-Id: I7fec9f88aa68b2ae947e34a1aede311e9fed2d05
CRs-Fixed: 3117535
Extend gStaPrefer80MHzOver160MHz ini to limit STA connection in
80MHz BW for HE/VHT mode. In case of XR use-case, higher
throughput is not needed but higher reliability is expected.
This ini helps in XR glass device to always connects in 80MHz.
Change-Id: Icefd2d54214351c04dd7420269c308cec2b5ae31
CRs-Fixed: 3117216
Intersecting EHT beamforming configuration from ini and FW
indication, then save it to eht caps of mlme.
For sta, update mlme EHT beamforming configuration to FW
through WMI_VDEV_PARAM_SET_EHT_MU_MODE directly.
For ap, intersecting mlme EHT beamforming configuration and user
configuration, then send result to FW.
Change-Id: I3d6185896af9fc58eb1fb6db913d4a425f72c696
CRs-Fixed: 3113235
Currently coex unsafe freq event is honored from firmware using
"wmi_wlan_freq_avoid_event_id".
As per requirement, add ini to don't honor coex unsafe freq
event from firmware and use the coex unsafe freq list from
vendor QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY_EXT.
Change-Id: Ia3acbc133cab4865d8ad69992e893be91439f705
CRs-Fixed: 3114742
For MLO Roaming,
- RSO offload commands will be sent
to FW only on assoc vdev.
- Add new state for link vdev, will be
used only during roam sync.
Link vdev RSO state change : DEINIT -> MLO_ROAM_SYNCH -> DEINIT.
Change-Id: Ifb89e23fc48356ec8f0bc6a045f2dd4d81038076
CRs-Fixed: 3098570
Currently in SAP mode, when host driver receives disconnect for
station, first it gets disconnect stats with serialization command
and then it sends delete peer command to fw. There is an issue with
this approach, if there are maximum number of clients are connected
to a SAP and all of these clients gets disconnected at the same
time, in that case there will be a disconnect stats command and
peer delete command in serialization, because of which serialization
queue gets full.
To address this issue, remove disconnect stats command from
serialization and send this command just before sending peer
delete command once peer delete command gets serialized.
Change-Id: I2fa1a5a393939eebbce796e11348fa7c040b40e8
CRs-Fixed: 3100914
Currently, MAC address update is supported only when interface is down.
Because of this framework needs to issue interface down and interface
up to update the MAC address. Interface down and up will lead to VDEV
delete and VDEV create commands to the FW.
To optimize Host-FW interactions during set MAC address, add support
to update the MAC address without bringing the interface to down state.
Change-Id: I76afa8f8c2504e8271bf689392d526f994afff0a
CRs-Fixed: 3063201
Add ini "disable_mcs13_support" to disable mcs13 to when SAP working
on 80p80MHZ/160MHZ/320MHZ and mcs12_13 supported.
Change-Id: Iff7043cc422cbe00fa771fe5fad9ad992d6deaf5
CRs-Fixed: 3062196
Add support for QCA_WLAN_TWT_SET_PARAM command to configure
QCA_WLAN_VENDOR_ATTR_TWT_SET_PARAM_AP_AC_VALUE attribute.
This attribute provides access category value for
WMI_PDEV_PARAM_TWT_AC_CONFIG. This is used by firmware to
configure access category for TWT HW queue in TWT Responder
mode(SAP).
Change-Id: I06a14d099c516767fe57ba94acc2a5fb95dc4e17
CRs-Fixed: 3052909
Besides MLO, legacy mode 6G SAP + 5G(2G) SAP are going to support RNR
IE. Move RNR related flag from MLO to private mlme component.
Remove mlo_rnr_updated in struct mlo_link_ie_info.
Add notify_co_located_ap_upt_rnr and related API in mlme_legacy_priv.
Change-Id: Ife86d1ed2fe8b633f6167750053b2aff37911299
CRs-Fixed: 3092483
Handle SAP and MLO STA concurrency such as:
1) If MLO STA is present with both links
in 5/6 Ghz then SAP comes up on 2.4 Ghz,
then Disable one of the links.
2) If there is channel switch for sap from
2.4 ghz to 5 ghz, then enable both the
links as they were disabled by previous
operations when sap was on 2.4 ghz.
3) If MLO STA is present with both links in
5/6 Ghz and SAP, which was present on
2.4 ghz, stops then renable both the as
one of the links were disabled because
of sap on 2.4 ghz.
Also, in case where MLO STA roamed from
5 + 6 link to 2.4 + 5/6 link force scc
will happen and the disabled link has
to be enabled.
Both links should only be enabled if mlo
sta has more than one links.
Change-Id: I0fd0093b20336ae32325981589c399b44a44b64e
CRs-Fixed: 3092202
