The rechecks count in dsi_display_status_check_te defines the
number of times the TE status needs to be checked before exiting.
Avoid the execution if rechecks is set to zero as it would avoid
unnecessary irq status changes.
Change-Id: Ice31701ac06f5b0a82f29b5f415dcb0b055e7b16
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
when a broadcast DSI command is scheduled, the command can get
triggered close to the schedule line. This might cause DMA
timeout. This change reads the video line count from
MDP_INTF_LINE_COUNT register and checks whether DMA trigger
happens close to the schedule line. If it is not close to the
schedule line, then DMA command transfer is triggered.
Change-Id: Ida92e63e46b4cc703d57ce24097834f810776aa8
Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
Add check to avoid the dsi panel status check with TE
method as the GPIO support is not available in Trusted-vm.
Change-Id: I5ad6e7b77b189b5150302ab34767dfc4d97aaf61
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
Add support to trigger ESD through debugfs by directly
modifying the reset GPIOs TLMM register in trusted-vm as GPIO
driver support is not enabled.
Change-Id: I859affe69c13dbe115a48b0a63a600a57027db58
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
Parse all the GPIO pins used by the DSI host and the display panel
along with its register ranges and store it in panel struct. This
avoids parsing the device-tree everytime during transitions between
trusted and primary vm.
Change-Id: Ibbb646358c0409703afda1c4f758f044fc8c0001
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
Currently, mdp_intf_line_count and mdp_intf_tear_line_count register
addresses are defined in dsi_ctrl_hw for debug feature. But mdp_intf
base address is target specific and independent of dsi controller
version. This change adds support for parsing the mdp intf base
address from dt, thereby remapping using base + offset addressing.
Change-Id: Ibb72dfe84a786a5c8b95f6a400e8333f6b46814a
Signed-off-by: Lipsa Rout <lrout@codeaurora.org>
Drm driver will remove the same mode that defined
in dsi panel dtsi. But the mode count was not updated,
so when checked drm mode, need to recount the mode.
Change-Id: I51a2c40ceb7d4ee83a15f74d9d724b4fb9c8a618
Signed-off-by: Zhao, Yuan <yzhao@codeaurora.org>
This change adds dsi display ramdump support when DEBUG_FS
is not enabled.
Change-Id: Ic6659a9380acd5eb55a3270d3e3b7016a9cd2bd7
Signed-off-by: Narendra Muppalla <NarendraM@codeaurora.org>
During ESD check failure, DSI video engine can get stuck
sending data from display engine. In use cases where GDSC
toggle does not happen like DP MST connected or secure video
playback, display does not recover back after ESD failure.
This change adds support to perform soft reset when DSI
video engine gets stuck.
Change-Id: I9cb31e6c71c4da171f9fe22fc3bee9175711831d
Signed-off-by: Ritesh Kumar <riteshk@codeaurora.org>
Change clears the DSI TX command buffer allocated for debugfs
command transfers and destroys the command packets in case of
error during command transfer.
Change-Id: Ia1e822b9b60d44f7eba325116d416916419471fa
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
The change batches DSI commands sent using the debugfs node, in a
separate buffer from the TX command buffer to ensure that they are not
triggered before the last command bit is set. Once the last command
bit is set the buffer is then copied to the DSI TX buffer and triggered.
Change-Id: I9ba624e4e19341696a974994817603315c6c8a45
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Currently, PLL_CFG1(1:0) register is updated with cached values
in dsi_pll_enable. This can create issue when UEFI and kernel
cfg1 programming is not same. To fix it, return cached value
of cfg1 when its read in pclk_mux_read, so that pclk_mux_write
is called and cached value is updated.
Change-Id: I1e45ff0685797bf4dd2e3a52af4753425f31edfc
Signed-off-by: Ritesh Kumar <riteshk@codeaurora.org>
Currently, changing panel configuration from firmware approach is present
for single display. This change adds support for secondary display using
firmware approach.
Change-Id: I8095dceed1567d8582c7473c0ac7f59c4666a200
Signed-off-by: Lipsa Rout <lrout@codeaurora.org>
In current implementation qsync min fps is single value.
It is same for all the list of supported dfps list.
Added support for new dt entry dsi-supported-qsync-min-fps-list
corresponding to the fps supported in the dfps list
dsi-supported-dfps-list.
Change-Id: Ifd5309c2f51865a3c0d9fadb65cbcd291b6ef42b
Signed-off-by: Raviteja Tamatam <travitej@codeaurora.org>
This change adds support to have same panel names for dual displays.
Without this change, the secondary panel bind will fail if it has the
same panel name as primary since the primary panel debugfs directory
would have been created during its display bind and when display bind
for secondary panel is initiated with the same name it will try to
create a debugfs directory with the same name resulting in bind failure.
This change appends a string as secondary in the panel name and creates the
debugfs directory.
Change-Id: I2bd25672ce0105a3b8225bbf17e13d4e373ad10b
Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
Currently, in firmware approach, the panel node is null
for secondary display. As a result, the number of display
remains one, in case of dual display also. This change
updates the number of displays.
Change-Id: I4b945b8b94d931e0dedf7ca7b27cb1a288b9d6ab
Signed-off-by: Lipsa Rout <lrout@codeaurora.org>
For phy ver 4.0 chipsets, configure DSI controller and DSI PHY to
force clk lane to HS mode always. This change was missed while
propagating from 4.19 to 5.4.
Change-Id: I60370034f7b9ed5d036d9d22f0807250afbcbcd5
Signed-off-by: Ritesh Kumar <riteshk@codeaurora.org>
Change decreases logs during a mode set in dsi_display and adds the
info to event logs.
Change-Id: I3bbe328f942008004c15b39230dd8be3e4cb64b5
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
The file operation write expects a non zero return value for a
successful exit from the file op.
Change-Id: I5e956333f39c33708ba24e2722713484c613f0ee
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Enure that ESD check doesn't result in a false negative while
booting up with a simulation panel or if TE based check is enabled
and panel switches it operating mode to video.
Change-Id: I62ff088f513d28d2883ce5a6d22f8bac1783fcd2
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
During stability stress testing, there are many instances where
the panel is unreachable which results in the ESD check mechanism
failing continuously with PANEL_DEAD events. There are two possible
reasons. Either the device is bad or DSI controller is hung. As of
today, logs/xlog is flooded and info on root cause is missed in the
logs. To catch the root cause for such issues, this patch induces
forced crash when there are five consecutive ESD check failures.
Change-Id: Id0a5762ac977f8a209af651f65cbe9da199cb8d0
Signed-off-by: Lipsa Rout <lrout@codeaurora.org>
Setting a lower load can make the regulator enter into LPM. Now the
lower load was set before the regulator disable, there's a risk here.
The regulator has been LPM, while it was not disable, if the cosumer
has a higher current needed than LPM at this time, that will lead OCP
on this regulator. The right operation for a regulator enable/disable
should be:
1. regulator_set_voltage(vreg, active_min_uV, active_max_uV) and
regulator_set_load(vreg, active_load_uA); in either order
2. regulator_enable()
3. regulator_disable()
4. regulator_set_voltage(vreg, inactive_min_uV, inactive_max_uV)
and regulator_set_load(vreg, inactive_load_uA); in either order
Change-Id: Ibe4f888a5675baf2691e479daa163d8867902e69
Signed-off-by: Zhao, Yuan <yzhao@codeaurora.org>
Currently, SDE relies on DSI to set a flag for POMS however
if a power ON modeset comes with a different mode than
previously configured, DSI is unable to detect the mode change
and does not set the flag nor perform the mode switch itself.
DSI should always align the panel mode to match the timing node
that is selected regardless of prior configurations.
SDE encoder can detect if POMS is required for the INTF block
without the flag from DSI by comparing the currently configured
INTF mode with the panel mode that is being set. The POMS flag
from DSI is still needed for any active panel mode change so
that the post-modeset cleanup operations are triggered.
Change-Id: Ib198b3098f21338ab35b2022b04be1c01c4cbd94
Signed-off-by: Steve Cohen <cohens@codeaurora.org>
Need to check trusted VM environment when loading DSI
firmware. Add this missing check due to propagation
issue.
Change-Id: I7c84b487a58133df49ba23e80e6b6ff8783cdf6c
Signed-off-by: Ray Zhang <rayz@codeaurora.org>
It is not applicable for all DFPS cases to update UIDLE state
according to current frame rate. If DFPS changes frame rate
through vertical front porch values, the SDE clocks and transfer
time will not get changed accordingly, and it always get fixed
at max frame rate configuration of DFPS.
Add this change to check max FPS of DFPS instead of current
frame rate for UIDLE update, if DFPS is enabled with VFP.
Change-Id: I7634bce6a9eb1af212ba19a267735be08b20ae1f
Signed-off-by: Lei Chen <chenlei@codeaurora.org>
Currently,power resource disable fails when pm_runtime_put_sync
returns negative values. Due to this, clock state update is
failing. pm_runtime_put_sync can return negative values in
scenarios where pending resume requests take precedence over
suspends. This change allows pm_runtime_put_sync to return
negative vales also.
Change-Id: I1a46ca574129ba953ddb6300f9b3ab24cdb3171e
Signed-off-by: Lipsa Rout <lrout@codeaurora.org>
Signed-off-by: Steve Cohen <cohens@codeaurora.org>
Currently, power_state variable does not reflect the GDSC
status. Due to this, there are scenarios where ctrl_power_on
is not happening leading to clock failures. This change
updates power_state based on current status of all the
regulators. GDSC enable is moved to pre_clkon and GDSC
disable is moved to post_clkoff.
Change-Id: I6d9508d5dffda0c94bd3b3bd9b5feb4724dc9dc7
Signed-off-by: Ritesh Kumar <riteshk@codeaurora.org>
[cohens@codeaurora.org: fixed static analysis error]
Signed-off-by: Steve Cohen <cohens@codeaurora.org>
