This change adds rx filter reservation, addition,
deletion anad release support for optional wifi datapath
feature. The parameters required for the rx CCE filters,
are passed to FW in the HTT message. FW responds with the
result of the request. Rx data packets matching the applied
filter parameters are routed to specific REO rings.
Change-Id: I6762912bbb2aefce940d6fa3cea4871a7c89409c
CRs-Fixed: 3401148
Currently, there is a compilation error on the
OWRT SI in the alternate code path when optional
dp feature is not enabled.
The caller wlan_ipa_wdi_init_set_opt_wifi_dp() passes an
argument of incompatible type. This change fixes the
compilation issue.
Change-Id: I1f2eecbb67bfb2ef17ee73ce2faedb85827b4bbc
CRs-Fixed: 3417214
This change adds the optional wifi datapath feature
to transfer data to and from modem via WLAN.
By using the existing path between WLAN and IPA, this
change registers new interfaces between IPA and WLAN
to reserve, add, delete and release rx filters,
which are required for setting up CCE filter rules.
These filters help to determine which packets need
to be routed to IPA specific REO rings.
Change-Id: I17c2ab77ae343f15d6b79fa02bb70ed62294089c
CRs-Fixed: 3403314
Add 160 MHz and 320 MHz BW support for Smart Antenna.
Peer connect gets rate codes for all supported BW on connecting peer
as part of wmi_peer_ratecode_list_event. This changes add 320 MHz and
160 MHz BW support.
Change-Id: I715dd5a64c38114fef6e17c2e2f6a526e1a716c2
CRs-Fixed: 3381648
Currently, hardware supports checksum offload for only ipv4, tcpv4/v6 and
udpv4/v6 packets. But driver sets checksum as CHECKSUM_UNNECESSARY for
all rx packets if tcp_udp_err and ip_err bit in rx_attention_tlv is not
set. If driver sets CHECKSUM_UNNECESSARY in skb then network stack will
not validate checksum and will reply to even wrong checksum packets
which is incorrect.
So, fix is to set checksum for all rx packets other than ipv4, tcpv4/v6 and
udpv4/v6 to CHECKSUM_NONE instead of CHECKSUM_UNNECESSARY so that network
stack validates checksum.
Change-Id: Ifb9c74fb729361da6db715fa667f926b71ce948f
CRs-Fixed: 3378925
For WDS ext use fr_ds and to_ds fields to check for
4-addr instead of reading value from TLV
Change-Id: I261746018de2320367e8650332a5c355edfb1489
CRs-Fixed: 3410639
In the case of MLO connection, MLD address is used for data
transmissions in the ethernet header. Take MLO-SAP intra-bss
forwarding as an instance, ref1 sends unicast arp-resp to
ref2 who initiates broadcast arp-req. DA and SA in the ethernet
header are both MLD mac addresses of ref1 and ref2.
Currently when WLAN IPA component does the intra-bss forwarding
check, MLO connection is not taken into consideration, where
only legacy hash table is searched. For a MLD peer, it is not
added into the legacy hash table but the MLD specific hash
table.
Hence in this change, use dp_peer_hash_find_wrapper() API with
CDP_WILD_PEER_TYPE to check if peer exists in both legacy
and MLD hash table.
Change-Id: Ifea7cd37373e1575d811bedefb602d0df5c1765b
CRs-Fixed: 3400280
Adding MLO timestamp offset reported from firmware to tsf time for
radiotap header populated in tx monitor.
Change-Id: I44f2c1a49d4d2b73ac9117319b72ba8635cb5b38
CRs-Fixed: 3398345
WIN and MCC shared a common definition od qdf_nbuf_cb
considering that there are various fields which are
not common it is decided to have 2 different definitions
for WIN and MCC. in case of WIN he per pkt cycles will
be significantly reduced in RX path.
CRs-Fixed: 3257879
Change-Id: I5d3fa7c91592afb905702f2dca49972be89664e3
Reuse the tx descriptors released in tx completions
without releasing the associated skbs to reduce
the cpu utilization in direct switch mode.
Change-Id: I4ab3ac58977a626344877b8a818a4dbc4864aaf3
CRs-Fixed: 3393968
1. Maintain and fetch PPEDS profile from be_soc instead of be_vdev
2. Enable WDS EXT mode for Direct Switch
3. Provide cdp API's and structures to interact with osif
layer to get PPEDS profile info
Change-Id: I997126e3b5ae85dabdcd6053115927122b8681da
CRs-Fixed: 3404778
Add TLV recording support for Rx monitor. The TLV
tag and its data are recorded in a fixed size buffer
Change-Id: Idad896d1ece25a499ab76028c8a231fcd9947f66
CRs-Fixed: 3402543
The kernel-doc script identified a large number of documentation
issues in dp/wifi3.0/dp_rx_defrag.[ch], so fix those issues. In
addition, there are a number of instances where public functions have
their implementation documented instead of having their interface
documented, so move that documentation.
Change-Id: I4080e4b614c5d1f0253afd06fc4eb650142b76d4
CRs-Fixed: 3373163
The kernel-doc script identified a large number of documentation
issues in dp/wifi3.0/dp_txrx_wds.[ch], so fix those issues. In
addition, there are a number of instances where public functions have
their implementation documented instead of having their interface
documented, so move that documentation.
Change-Id: I2f80d9715f772a59072f2c4158548f47df8bb055
CRs-Fixed: 3373164
The kernel-doc script identified a large number of documentation
issues in dp/wifi3.0/dp_internal.h, so fix those issues. In addition,
there are a number of instances where public functions have their
implementation documented instead of having their interface
documented, so duplicate that documentation. The documentation at the
implementation will be removed separately.
Change-Id: I9684f5c2da7edb621a53dfbc5f1f8de2c70d8382
CRs-Fixed: 3373166
The kernel-doc script identified a large number of documentation
issues in dp/wifi3.0/dp_ipa.[ch], so fix those issues. In addition,
there are a number of instances where public functions have their
implementation documented instead of having their interface
documented, so move that documentation.
Change-Id: I664c657e4e7424db576bf19ca8a26c697b37e46f
CRs-Fixed: 3373165
Previous the following patch fixed all of the known kernel-doc issues in
dp/wifi3.0/dp_types.h:
Change-Id Ie93b7f802926e562169e51a56e5fc83de845b310
qcacmn: Fix dp_types.h documentation
Unfortunately, concurrently the following patch introduced a new issue:
Change-Id I8bc0c3c78e3eb8c6679e00442d607615bab38f96
qcacmn: Add mcast enhance flow for single dev
And subsequently the following patch introduced two more:
Change-Id Ic3c8122fca9124e41931ec445946aec5e8863434
qcacmn: Add datapath config event history
So fix those three new issues.
Change-Id: Id1416a1426e5442f1e96db4da35412ef5374e568
CRs-Fixed: 3403640
The kernel-doc script identified a large number of kernel-doc issues
in the dp/wifi3.0 folder. A series of patches have addressed most of
the issues, so now fix the remaining issues. Just like in the previous
patches, there are a number of instances where public functions have
their implementation documented instead of having their interface
documented, so make sure that the interfaces are documented.
Change-Id: I4bc39b0e1a9d8c264b72ec6db76ff7e92d24f277
CRs-Fixed: 3373822
The kernel-doc script identified a large number of documentation
issues in dp/wifi3.0/dp_tx_desc.[ch], so fix those issues. In
addition, there are a number of instances where public functions have
their implementation documented instead of having their interface
documented, so move that documentation.
Change-Id: I349f0e9d9336ae632fb31e88ddc34ecacc4a1f68
CRs-Fixed: 3373161
Previous the following patch fixed all of the known kernel-doc issues
in dp/wifi3.0/dp_rx.h:
Change-Id Id0ac49ebfa23790346384d688cc6346f513a7969
qcacmn: Fix dp/wifi3.0/dp_rx.* documentation
Unfortunately, the following patch introduced two new issues since
it copied incorrectly formatted documentation that had not yet been
corrected:
Change-Id Ic51a9742f65cee677ed7f3081f49fb3ece5b42f1
qcacmn: Optimize DP Rx Error Handling (Part-1)
So fix those two new issues.
Change-Id: Iea99708e31564525d0d4a0d94ea04ef9aa036ed8
CRs-Fixed: 3403645
The kernel-doc script identified a large number of documentation
issues in dp/wifi3.0/dp_tx.[ch], so fix those issues. In addition,
there are a number of instances where public functions have their
implementation documented instead of having their interface
documented, so move that documentation.
Change-Id: I7a09c451f3f4af3dd606778c49cce81677f6fe58
CRs-Fixed: 3373159
The kernel-doc script identified a large number of documentation
issues in dp/wifi3.0/dp_peer.[ch], so fix those issues. In addition,
there are a number of instances where public functions have their
implementation documented instead of having their interface
documented, so move that documentation.
Change-Id: I996764f93addfa270ef7aaedd2e23c71be287f77
CRs-Fixed: 3373168
REO_FLUSH_CACHE cmd
- flush_q_1k_desc as 1 – This will flush Queue, Q1k and QEXT in one go.
we need not give 11 cmd for each tid of the peer.
- forward_all_mpdus_in_queue to 1 in FLUSH_CACHE_CMD.
With this we need wait for aging threshold time.
Change-Id: I695ab48a50968872eb22024ba5c770f0e5a74a09
CRs-Fixed: 3384665
Adding check for num users and num ul users to not cross max users limit
And convert target uplink trigger tid to data tids
CRs-Fixed: 3396991
Change-Id: I66180dba0889e116ce8ff4e582fd9c1d8391f27b
The kernel-doc script identified a large number of documentation
issues in dp/wifi3.0/dp_htt.[ch], so fix those issues. In addition,
there are a number of instances where public functions have their
implementation documented instead of having their interface
documented, so move that documentation.
Change-Id: Ic8eb4c5e7f04de45a785aa4278cb97f1895e53d1
CRs-Fixed: 3373162
Make DP changes for handling umac reset in QCA5332.
Changes are done to program msi_data value of the IPC interrupt to FW.
Change-Id: Ib6453755e191da655b87b528a7cef38a464f316b
CRs-Fixed: 3401146
In print_peer_stats function while printing REO Q
ref. table if the input peer is MLD peer then the
API to check a valid MLD peer, returns NULL, hence
calculated peer index is invalid causing OOB array
access for REO Q Ref. table resulting in crash.
Fix, For MLO Link Peer REO Q ref table is not
updated and hence return from function without
printing. For MLO MLD peer update the API to check
the peer type and update peer index accordingly.
Change-Id: I66208410bd7a44d381c470621d10c118040d903a
CRs-Fixed: 3401569
Previously all of the documentation issues in the dp/wifi3.0/monitor
folder were fixed by:
Change-Id I27e14544ef88193bbfe6ee409fe58c59d6b5bea2
qcacmn: Fix dp/wifi3.0/monitor documentation
But concurrently a separate patch introduced a new issue in the
dp_rx_mon_pkt_tlv_offset_subscribe() documentation:
Change-Id I9e5d6cbb32cc7469dc367f6fc4bca4ce8adc9da8
qcacmn: Word mask TLV support for monitor
So fix that issue.
Change-Id: I174b19d9dded26d14af6eb94115a1c461a2f9e6f
CRs-Fixed: 3401990
The kernel-doc script identified a large number of documentation
issues in dp/wifi3.0/be, so fix those issues. In addition, there are a
number of instances where public functions have their implementation
documented instead of having their interface documented, so move that
documentation.
Change-Id: I15c8570aa1832ed053fa38f536fa36b2ca0aa56b
CRs-Fixed: 3373157
In case of split phy return the partner vdev from
same SOC for intrabss forward
Change-Id: Id7d2acd80d60e4d5cfb6df821f72a8d885d8fe57
CRs-Fixed: 3398627
The pointer to next TLV in status buffer is considered
as valid, only if atleast the TLV header size is available
within the status buffer.
Change-Id: Ic222bfab4790853ee012de4b0a860ab037972ff5
CRs-Fixed: 3378058
1) In WBM2SW Rx Error path, code to reap and
the process the HAL descriptor is split into
BE and LI architecture specific functionality
in dp_be_rx and dp_li_rx files respectively.
2) The function to handle Null Queue desc.
error for WBM and REO Rx Error path is split
into BE and LI architecture specific
functionality in dp_be_rx and dp_li_rx files
respectively.
Change-Id: Ic51a9742f65cee677ed7f3081f49fb3ece5b42f1
CRs-Fixed: 3356179
Raw mpdu check in dp_rx_reo_err_entry_process() is introduced
from change "Free the raw mode mpdus in REO error ring",
it is fixing the low memory issue during MLO STA T-put test
which reports REO error code 0 - HAL_REO_ERR_QUEUE_DESC_ADDR_0
frequently.
this introduce regression for SAP certification case 4.3.3.1.
it seems REO error 0 is hard and not expected to be reproduced
during MLO STA T-put test, remove the raw mpdu check in
dp_rx_reo_err_entry_process() to not block SAP certification.
Change-Id: I509e80eb38d57f20b24c32ba1da2ad7132358030
CRs-Fixed: 3387453
Change flow idx invalid to flow_idx_valid.
This change is made so that flows for which this field is not present
are identified as invalid flows and not forwarded to PPE.
Change-Id: I92c82bb0ef57012b2b884fe3fd18344b523a3f51
CRs-Fixed: 3390588
