Add new files for connect/roam logging. Add changes to
initialize the logging buffer.
Make changes to support enqueue/dequeue log.
Define enums for MAIN_TAG, Sub TAG, category.
Add structure definitions for logging buffer.
Change-Id: I1d283fcf464da90d4f5533214d480ddda156ec27
CRs-Fixed: 3013486
Check fw capability to support p2p + p2p concurrency from
soc_fw_ext_caps and based on fw capability, set policy
mgr concurrency for p2p + p2p.
Change-Id: Ia32f81f37174e9d722911b1fae6d4897d0af9816
CRs-Fixed: 2991300
According to 11n CERT case - 4.2.44 AP WAP/WPA2 mixed security mode
test, AP works in HT mode, but driver disallow the 11n when TKIP
cipher present and switch to "A" mode, then no HT IE in Beacon.
Fix by check TKIP only cipher and other ciphter present(CCM)
to disable allow 11n.
Change-Id: Ia915c9aa45bef93a22b5f43004e533cc87978752
CRs-Fixed: 3033301
Currently, firmware can roam between owe security SSID's
even though open SSID is different for both of the AP's.
This commit adds support to restrict roaming between the
same OWE profile AP's which means if the device needs to
roam then target AP's open SSID and owe SSID should match
with current AP.
Change-Id: Ib59127a90cab9ee6626b018d581edbf76ad89856
CRs-Fixed: 3025667
Send additional roam trigger TLV for BTC in
WMI_ROAM_ENABLE_DISABLE_TRIGGER_REASON_CMDID
command, to support a new roaming trigger
"WMI_ROAM_TRIGGER_REASON_BTC".
Change-Id: Ib767bd6bcf005c187b0fb58986ad287fe8753c1b
CRs-Fixed: 3009788
To support BTC roaming, add a definition of BTC roam trigger
reason in ini roam_triggers. It goes to fw via roam_enable
trigger command (WMI_ROAM_ENABLE_DISABLE_TRIGGER_REASON_CMDID)
Change-Id: I231a72ed98a74fb1b5ced12da7c3932af12d485d
CRs-Fixed: 3009787
Currently the PS config received from kernel/userspace is set
to mac_ctx globally. This causes PS config set for one vdev to
override on the other vdev.
To avoid this, set the PS config per vdev.
Change-Id: I6a2e2a9d8fb67b94d9d5f1d4164077990bdaf4a5
CRs-Fixed: 3007060
User configuration support to use scan request BSSID value
in Probe Request frame RA during the scan.
Change-Id: Ie0b7620428e1bfbd51e7430b6b7ad23ebede9e67
CRs-Fixed: 3021525
Currently, the WLM mode could be recovered after disconnection
or interface down/up about random MAC feature. Since some OEMs
have different mechanisms to config WLM mode on their framework
implementation and don't expect recovering the WLM mode.
So add logic to set default WLM mode when disconnection happens.
And add ini wlm_latency_reset_on_disconnect to differentiate
the implementation in driver. By default
wlm_latency_reset_on_disconnect is false.
Change-Id: Idcb3baf6ab8f0533eb01c28ff1c12513f9995946
CRs-Fixed: 3006875
Add configuration support for broadcast TWT support and Rx control
frames to MultiBSS HE capabilities.
Change-Id: I2b3075a21c919c120e7a1ff674ac33fdd5d73801
CRs-Fixed: 2979513
Currently addba response is not updated with ini configured rx aggregation
size.
This change is to reject peer addba request if rx aggr size is 1 and
for other sizes select min value of peer and configured sizes.
Change-Id: Ia375b1e031dfecf948429e0baea19faa8fe42ffa
CRs-Fixed: 2962314
When TSPEC session is deleted, the access category of the data packets
should be downgraded to next lower AC. But this is not happening due to
acm mask is not getting updated when bss descriptor is NULL.
To fix this ssue, update acm mask from bss descriptor only when beacon
IEs are not present.
Also move qos related logic to LIM and bring missig changes which were
there before connection manager.
Change-Id: I9da80cf492b01762b4cc0a7b73271a0f5fe4b4a4
CRs-Fixed: 3011069
Peer addba request is rejected when reject_addba_req is set from
ini or vendor command.
Current reject_addba_req ini is replacing with gRxAggregationSize
when it is set 1 from ini.
Hence this reverts commit I80a4b78c1af77f5bfa68be3163f9e9a78cc64245.
Change-Id: I1cc57b88311da4dd8f26eade17072aaa1f0ebb59
CRs-Fixed: 3002204
Currently, the SAE authentication request retry happens
after a fixed timeout of 1 second in a STA DUT.
To make this timeout user configurable, add an INI to
configure SAE auth failure timeout.
Change-Id: I3a3944ab14564a944e0c83cc31a92847b5e8c5e0
CRs-Fixed: 3011892
Based on new requirement, add aliasing for gNeighborLookupThreshold
ini and update the range of this ini as well.
Change-Id: I0a62e209d6a62001d6aec48849c4900062ae5bc7
CRs-Fixed: 3011060
Currently driver has only one name for an INI, with
this change add second name as well for few INIs based on
new requirement.
Change-Id: I6eee13935d1c5c74794027b88d94cbb572339e9e
CRs-Fixed: 3007209
Save dual sta configuration in hdd context and
restore it after SSR. This allows driver STA + STA
connection in MCC/SCC.
Change-Id: Ia8bb8c845f0f76e7ce41ff32ab0a3bc6d5111018
CRs-Fixed: 2998225
Set gRemoveTimeStampSyncCmd ini to 1 by default so that even for more
than 60 seconds, the device can stay in RTPM WoW mode.
Change-Id: I560389dd9c7d5a33d01c092ad057a7a7aa6f7c37
CRs-Fixed: 3003718
Currently, wmi_roam_event_id data is extracted and processing is
also done in wma. This is not inline with component model where
target_if takes care of data extraction and handover the extracted
data to corresponding component(connection mgr in this case).
Add changes to support the same. As the legacy CSR/LIM is not
yet converged, have a wrapper from connection mgr to wma to call
these legacy APIs.
Change-Id: I0e22bbccfe21200b90771a01f9ee7454f4ecb119
CRs-Fixed: 2990355
In a beacon template, there is a mismatch of twt responder bit in
HE caps and extended caps.
During start BSS, there is a kernel flag related with twt
responder. Intersect this kernel flag and service bit capability
before calling twt enable/disable api in start BSS.
Change-Id: I0725fc560904c622cc47f43958bcd490daacfa2f
CRs-Fixed: 2995538
Use wlan_cm_is_vdev_roaming() API in wma, instead of
wma->interfaces[vdev_id].roaming_in_progress.
Change-Id: Icb88246b2c45c052a1d42dece4983b1e534fe608
CRs-Fixed: 2993180
In case if TWT command (i.e setup, terminate, pause, resume,
nudge) comes from userspace and if the firmware is in below mode
1. scan in progress
2. roam in progress
3. CSA is in progress
4. any other error
then the command needs to be rejected in userspace context
Synchronize the TWT commands so that whenever command goes from
driver to firmware, then driver will receive ack event first
followed by respective event (i.e add dialog, delete dialog,
pause, resume, nudge) with below condition
1. If driver receives the ack event as successful then driver
waits for this ack event, respective event with status of the
TWT action frame over the air is expected.
2. If driver receives the ack event as failure then it will
reject the TWT command request in userspace context.
Change-Id: Ib68b89b74b5e44f28106884efd7412cee49f5bd8
CRs-Fixed: 2987978
csr has a mac address field which is redundant, the same can be
retrieved from the vdev object.
Hence remove the mac address field from the csr and update the same
from the vdev object.
Change-Id: I948cf858ddb26795e236aa4099186e5d10f504a6
CRs-Fixed: 2990480
Add sanity check for bmiss configuration from vendor cmd:
the device mode shall be station mode,
the final beacon miss value can't exceed ini max setting,
vdev_id shall correspond to the interface from vendor cmd.
Change-Id: I7ecdd40f69a8317ccd5362adbcad1159b1792ab7
CRs-Fixed: 2990863
Enable SAE Roaming with same PMK feature INI
sae_single_pmk_feature_enabled by default.
Change-Id: I5be1b24fd77f5296574276af02b0098ac86d9730
CRs-Fixed: 2985116
Add support to enable the "FT over DS" via
QCA_WLAN_VENDOR_ATTR_CONFIG_FT_OVER_DS vendor config
command.
This configuration helps the firmware to support
“FT over DS” instead of “FT over Air”
Change-Id: I493bf15f83bc39135aaeefa9d8ef328f0fc0cda3
CRs-Fixed: 2968680
Change ini type of all ini related to edca_ani, edca_wme,
edca_etsi. Also, use cfg_get instead of cfg_default for
fetching these.
Change-Id: Iba252f81d236c5b217e1d86c6511bbc52c2900b7
CRs-Fixed: 2952537
Station sends the BA and upgrades to the next possible BA window
size upon receiving all frames successfully from the current
window. Some IOT APs go out of sync from BA window size of the
station when AP fails to receive the BA sent from station. AP
transmits the frames again with previous window sequence number
and won't be ack'ed by station hardware as BA window has already
moved ahead. So, station deletes the upgraded BA and tries
to fallback.
Ideally, AP is supposed to consider the fact that "the previous
window transmission was successful when station upgrades to next
window size". But some APs take little longer time to
recover/upgrade to next window size. Don't delete the BA
immediately and have some tolerance(3 seconds) as the previous
negotiated BA just got deleted.
Change-Id: I6b277223f02dac521316cec20bd5d958785cc2e9
CRs-Fixed: 2970714
Currently only default values of local edca params are used for
WME and ETSI profiles. Therefore expose them as INI config options
so that driver is able to parse user configured edca params used
locally by SAP.
Change-Id: I81759570160a67e26f68501576d71a5fd3568cd7
CRs-Fixed: 2976143
Currently ini based tx aggr support disabled due to firmware
incompatibility.
This change is to enable ini based tx aggr support based
on firmware capability.
Change-Id: Id5d7197f18fafd926de889f9b69ca2be90497fd2
CRs-Fixed: 2859709
This reverts commit I9e49ad5218f913f116cf4472f768f572740f14df
since ini based tx aggregation is configured based on firmware
capability.
Change-Id: I54541cd282eda6606e75fa347989624a0e0fef01
CRs-Fixed: 2963280
Add INI configuration support to enable/disable BSS color collision
detection offload in STA mode.
Change-Id: I9d8f096813d74242566ccae5f92e872bcaca6295
CRs-Fixed: 2965133
Refactor csr_roam_pmkid_req_callback to use
mlme_cm_osif_pmksa_candidate_notify and move other
unused API under CM flag.
Change-Id: I835d54804f733eddff48de38e4c545a87f34bb30
CRs-Fixed: 2965602
The WTC parameters are stored in MLME vdev private object.
So the parameters are cleared once vdev delete is done.
Move the WTC parameters to psoc->mlme_cfg to retain the
values across disconnections.
Change-Id: Icecfbef19af994f8a05622501d435bfb63beca50
CRs-Fixed: 2959715
Existing INI disable_4way_hs_offload is defined as a boolean
that controls the EAPOL Handshake to be offloaded to Firmware or
Not. There is no way to specify the EAPOL offload per AKM.
Hence extended the support of EAPOL handshake offload to firmware
per AKM by converting this INI to a bitmap integer.
With ini value as 0 by default Firmware takes care of 4-way HS
during roam for all AKMs except for SAE and OWE. If
this ini value is 1 then Host takes care of EAPOL for all AKMs.
Having the backward compatibility, added a new value to ini.
If this ini value is set to 2 and also if the SAE EAPOL offload
service bit is set by Firmware then the behavior is same as ini
with 0 except that Firmware takes care of 4-way HS for SAE roam
as well. And for OWE it is still handled by supplicant.
To achieve this, new roam offload flag is introduced to indicate
Firmware about SAE roam EAPOL offload, So that in Roam sync
indication Firmware will inform the status as connected but not
authenticated so that supplicant can take care of 4-way EAPOL HS.
Change-Id: I8b65a1768fad91fac7e427712d3ccf4586176f5f
CRs-Fixed: 2955029
