In some cases we need to classify frames accordinging
to l3 type. This change mainly focus on this issue.
Change-Id: I4bc49a808a02b4bc8c65f920690922045d65e739
CRs-Fixed: 3198481
Currently 11be msdu rate statistic is not supported yet.
Another issue is: HW reported pkt type value 6, while host
SW defined 11be type DOT11_BE (value 5), they are not matching.
DOT11_BE value 5 is referred in monitor mode and otherwhere,
so do map and conversion in host sw side.
Change-Id: Ic5c2dd2a35cbe0ecd6430f007b6e7e02ece40998
CRs-Fixed: 3230900
Direct DMA source ring type has two rings where ring0 is
used for Spectral and ring1 is used for CFR. The current
hal_srng_ring_id do not have the ring_id defined for CFR,
which leads to wrong ring_id populated for TX MON feature,
which collides with CFR ring.
Fix the same by defining ring_id for CFR.
CRs-Fixed: 3220401
Change-Id: I778cea533a1907ae6cd94f63734ca6c967891b9d
For QCN9224 target, All the MIC failures are reported
as decrypt error from FW.
So, added changes to handle MIC failures for QCN9224
target .
Change-Id: I32e616e01e3cd6e76ef105d73fd8a87ce2c81cb9
CRs-Fixed: 3192749
The original BA window size given from CP might > max DP supported,
add sanity check based on HAL target allowed.
Change-Id: Ibadaddeffe65165a89d580d8a5cbf5f7c724c809
CRs-Fixed: 3193852
Shadow config v2 can support max of 36 shadow
registers only. For KIWI target, there are 40
shadow registers supported.
Hence add support to send shadow config v3
for KIWI.
Change-Id: If57e6597397da3e239f25a6c0cc24f8fd37dcdf1
CRs-Fixed: 3167758
1. Since peer id is reused for reconnection in MLO case,
old entries for queue desc addr is cleared. Clear the reo
internal storage and reset it back on client connection.
2. Send Qref feature WMI cmd to FW to enable the feature.
Change-Id: I6705ce121c8c25d9a2ace039dab21312fa5ea4b1
CRs-Fixed: 3156642
Add support for tx monitor flush/drop/truncated handling
and few minor fixes from txmon
CRs-Fixed: 3158502
Change-Id: Ic13476984cd591a381941cfa1501307e9cca2b5a
Currently in some case we are receiving non error packets on REO2TCL
ring, which is causing issue.
Fix is to set DEST_RING_MAPPING_0 to SW1 for REO dest ctrl
register, So that non error packets with reo_destination_indication
with 0x0 in the reo entrance ring will be routed to SW1 ring.
Change-Id: I67f78f35e7dba899943307902d99d0325a60498f
CRs-Fixed: 3150186
Add a separate APIs to configure RxDMA and RXOLE
configuration to enable the PPE based routing.
Change-Id: I95b8fbb361402bc04fc1f38aa8b0dbc6f99f4f06
CRs-Fixed: 3147720
Add feature support to tag first packet that wakes up HOST from WoW.
rx_pkt_tlv.rx_msdu_end.reserved_1a field is used by TARGET to meet
such request.
Change-Id: I3d37e13e8cff49bc4f622d3070a19e4c4be56417
CRs-Fixed: 3137621
Added HAL specific api to support tx monitor,
1. to get buffer address
2. get number of users
3. get corresponding structure to handle tx monitor and
4. parse limited TLV tag.
Change-Id: Ic354c76b3bcf5fa454db973c2aa4ee5f9c1b4208
In WIN BE chipsets, replace the REO tid
queue programming in FW via WMI with writing to a
Host managed table shared by HW and SW. REO HW will
pick the tid queue address from the table indexed by
peer id and tid number.
Change-Id: I8107ca5116425538329b11ae3519f02b32573bac
Add function pointers to free buffer address stored in status buffer
and support tx monitor in legacy and Waikiki flow.
Change-Id: I28612d388009292ff751fe514183fb801909f485
- Fixes for compilation issues after enabling
monitor 2.0 support.
- change copyright year for all files in the chain.
Change-Id: I885e257bd8ca83850656d8a1f408c1bc34920d7a
CRs-Fixed: 3086483
Add 2 hal soc ops, hal_msdu_desc_info_set and
hal_mpdu_desc_info_se for berilliyum datapath.
Attach hal_rx_msdu_ext_desc_info_get_ptr_be to its function
pointer.
Get reo queue descriptor address as a 5 byte value as in
beryllium datapath it is being obtained from rx packet tlv.
Change-Id: Ia58597384e1a3d5eec493b865a88bab4f209502d
CRs-Fixed: 3084532
In BE architecture, HW provides basic vdev stats support for upto
48 vdevs. For each vdev, there is vdev_stats_id which represents the
id of this vdev on HW. This vdev_stats_id is assigned by host and
is conveyed to HW at the time of REO TID Queue setup for the peer.
Add logic for allocation and deallocation of vdev_stats_id and
convey this id to HW.
Change-Id: If5611bf54d057ccf71c6444b5c79a26eb28df87e
CRs-Fixed: 3067843
Rx patch changes for multichip MLO
1. Create ini for rx ring mask for each chip
2. Configure hash based routing for each chip based
on lmac_peer_id_msb
3. Peer setup changes to configure lmac_peer_id_msb
to enable hash based routing
4. Rx Replenish changes to provide buffers back to owner
SOC of reo ring
Change-Id: Ibbe6e81f9e62d88d9bb289a082dd14b4362252c4
Changes needed for MLO soc attach to pass chip_id,
dp_ml_context from upper layer.
This change also takes care of assigning appropriate
RBM id for IDLE link descriptors based on chip_id.
Change-Id: I8f5f08c524d91942e6e458f048700b7bdd900107
Added an API to do a batch invalidation of REO descs
saw an improvement of 40 to 45 Mbps.
Note: this change is applicable only for cached
descriptors
PINE with Default driver: 3189 @ 100% core-3
PINE with skb prefetch: 3469 @ 100% core-3
PINE with skb pre + batch inv: 3506 @ 100% core-3
Change-Id: Ic2cf294972acfe5765448a18bed7e903562836c3
In WBM error processing read peer_id from peer_meta_data
instead of sw_peer_id.
This changes is needed because we need to process Rx packet
on ML peer. But in MLO case sw_peer_id field contains
link_peer_id where as peer_meta_data has ml_peer_id.
Change-Id: I3f469adfdf7efa88cb081e94fa9fe0c54c1fb078
This FEATURE_HAL_DELAYED_REG_WRITE_V2 was added to fix the
Audio jank issue, but it could not resolve it completely,
so that was later fixed by existing delayed reg write
support with the help of SMP2P messages to communicate
with FW regarding PCIe link status. This code is not being
used, so removing it and cleaning up the redundant code.
Change-Id: Iada088e72a76b4c071c8a80ee945f36ac959670e
CRs-Fixed: 3056475
Currently the EAPOL/ARP/DHCP frames arriving as 2K-jump
or out-of-order frmaes are being delivered to the network
stack, without checking for the packet-number sequence.
WCN7850 has hardware support to provide the packet number
of the previous successful re-ordered packet from hardware.
Use this feature to check if the packet-number are in proper
sequence for these EAPOL/ARP/DHCP packets arriving as 2k-jump
or out-of-order packets before submitting it to the network
stack.
Change-Id: I1078452afce4bc00b2509436295e5bd80000feb4
CRs-Fixed: 2965086
Currently the hardware srng register offset is statically
assigned to the handle. This can lead to incorrect index access
when targets (eg: wcn7850) is added which require additional
register offsets to be stored in the hw srng register offset table.
Move to the index based assignment of the srng register offset.
Change-Id: I8e38bdd0c28068029a0267fce706edf4378b9df8
CRs-Fixed: 2965081
WCN7850 has support for near full indication for
the consumer srngs. This interrupt is used to take
preventive actions to avoid ring full watchdog irq
trigger.
Register for the near full irq and add the necessary
ext groups for these near-full irqs.
Change-Id: Ic16381fceabc54e6c52b34dd13abea74cad4d38c
CRs-Fixed: 2965081
Add delayed SRNG register writes support for Tx Ring, also add
dedicated workqueue to do the delayed Tx SRNG register writes.
Change-Id: I8dd157d341f3035e988804eab50d1ca681ab789b
CRs-Fixed: 2868989
Currently the FW configures the mac with appropriate
offsets for rx pkt tlvs using the structure defined in
te FW and the host does not send the ring selction config
HTT message. This can create a problem when FW stops subscribing
to tlvs or changes its rx pkt tlvs offset.
Fix this by configuring the rx pkt tlv offsets via HTT
ring selection config message.
Change-Id: I1a2865f91b34dd7bda1af8651d7831097dac0bee
CRs-Fixed: 2860504
Change the alternate indication_0 to WBM instead of
REO2TCL. This is done such that, WBM takes care of
the of the de-linking of the link descriptors and
release the buffers to the respective WBM rings.
WBM should take care of the NULL entries if present
in link descriptor as WBM internal errors.
Change-Id: Ie084e54861bb4611a45cd724bb32d211c62f4f21
Add apis to map generic registers to shadow region. Existing
logic includes mapping only srng based regs to the shadow
region.
Add support to map REO control regs and WBM2SW2 rel
ring HP reg address to the shadow region in case the direct
reg writes in IPA enable/disable autonomy fail due to UMAC
block being in a power collapsed state.
Shadow reg mapping for these regs is provided to FW during
init. Add stat shadow_reg_write_fail to track shadow reg
write failure and shadow_reg_write_succ to track successful
shadow writes.
Change-Id: I04790765a3de80047689657e2cad0b73123440b9
CRs-Fixed: 2790321
If frames from the same FISA flow goes into different REO2SW rings, it
will result in an unexpected FISA behavior. This can happen if the
frames have been reinjected from FW offload module since FW will select
REO2SW1 ring. If the same flow frames hash to other REO2SW rings, then
the same flow UDP frames will do to different rings.
Reo_destination_indication of 6 indicates if the frame has been
reinjected from FW. If so, then continue to deliver the packet without
FISA.
Change-Id: I14a17a10d04909adfb30557d58beb1610e59bf70
CRs-Fixed: 2790292
