This change adds reg dma support for vig DE lpf.
Change-Id: I9108046bb2afb987eec49224df4a45c37f9c27cd
Signed-off-by: Renchao Liu <quic_rencliu@quicinc.com>
This change updates vsync source as part of rc post modeset. For some
use cases like idlepc with DFPS, vsync could be configured for
previous fps and can cause timeouts during next frame.
Change-Id: I110fd958d2970eaca50ace0e72c4faea3fc64ce8
Signed-off-by: Narendra Muppalla <quic_nmuppall@quicinc.com>
Avoid various possible nullptr dereferences.
Addresses various issues highlighted by static analysis.
Change-Id: I36d34d610b37bf2799a7e34cd1de8b909b5c0ae4
Signed-off-by: Nisarg Bhavsar <quic_bhavsar@quicinc.com>
To toggle error interrupts, we currently read the DSI_INT_CTRL register,
toggle the DSI_ERROR_MASK bit and write back to the register. While doing
so we are also writing back 1 to any status bits set by HW, thus clearing
the status interrupts. Clearing the status bits should always be done as
part of interrupt handling, which otherwise can lead to command transfer
failures.
Avoid clearing status interrupts while error interrupts are toggled.
Change-Id: Iaae10c279f2341269ed49074448167e68ab7e13c
Signed-off-by: Srihitha Tangudu <quic_tangudu@quicinc.com>
The software mvid/nvid values represent the ratio of mode clock
to link clock. Currently we are converting the link clock to vco
clock, get the ratio of vco clock to mode clock and then adjust
the resulting values to get the ratio of link clock to mode clock.
This change simplifies this logic by directly using the link
clock to get the ratio and uses fixed point arithmetic to scale
the resulting mvid, nvid values to meet requirements.
Change-Id: Ifdfa27edb73d2db6381e592db219e75806d6bdc7
Signed-off-by: Rajkumar Subbiah <quic_rsubbia@quicinc.com>
Check the precise vsync feature bit in sde hw catalog features
bitmap for checking the precise vsync feature and remove the
obsolete has_precise_vsync_ts variable.
Change-Id: I1f0cfabe5dcf387358548e8ff5ea0d65d4d7cecf
Signed-off-by: Veera Sundaram Sankaran <quic_veeras@quicinc.com>
Currently only LLCC_DISP SCID is used to read and write to
system cache during static display use case.
This changes adds SCID LLCC_DISP_1 to allow each SCID to
have a dedicated function (read/write).
Change-Id: I5604ec1183d99a8492b005ec06ac94e5db60b5f7
Signed-off-by: Amine Najahi <quic_anajahi@quicinc.com>
Currently a boolean variable is used to track if the system
cache feature is enable for a particular SCID.
This change converts it to use a feature bit instead.
Change-Id: I8461fd9fb837b871c4ac5c67a9ab7613aadea7bb
Signed-off-by: Amine Najahi <quic_anajahi@quicinc.com>
Merge reg_dump and dbgbus dump flag into dump_mode, and bring
back debugfs node "evtlog_dump" to keep flexible controlling
of evtlog.
Set in_mem option as default dump mode, since in_coredump
option will be enabled once HW recovery feature is enabled.
Change-Id: I75de1a69b01594b652479bf79201591ac0bf62e5
Signed-off-by: Bruce Hoo <quic_bingchua@quicinc.com>
Currently, when doze mode is enabled the encoder off work
worker is started 1 ms after idle power collapse because of
aggressive idle-pc feature. This causes the system cache
worker to start after the clocks and vsync interrupt are disabled.
This change independently enables clocks and interrupts during
system cache work thread to decouple it from the encoder
off work sequence.
Change-Id: I8ed172b0e7c5c8e4e270e768434301d972e90eb9
Signed-off-by: Amine Najahi <quic_anajahi@quicinc.com>
UBWC revision is in the expanded form, no need to process it again.
Change-Id: Ie4aafeea5459a76f325a07e58af1de5665fe45ba
Signed-off-by: Shamika Joshi <quic_shamjosh@quicinc.com>
HDCP sec_module is linked as an additional dependency for display drivers.
This change links hdcp_qseecom symbols needed for display drivers.
Change-Id: I227382dbf31b8488479b983b730d10b17c3b3af2
Signed-off-by: Vara Reddy <quic_varar@quicinc.com>
drm device pointer is not set in dp aux object which
is leading to a warning message during device bootup.
This change will set that pointer before registering
aux object.
Change-Id: Ib79ece56d7d5efd098e06104eb020648d1d075f7
Signed-off-by: Sandeep Gangadharaiah <quic_sandgang@quicinc.com>
Modified the pre-emph values for S3P0 & S1P1 in HBR/RBR
table. Also, modified BG timer value as per the latest
HPG changes.
Change-Id: Id9088d3cfe73cb14518dcf490676d92c54925793
Signed-off-by: Sandeep Gangadharaiah <quic_sandgang@quicinc.com>
Plane cache state is updated based on the crtc's cache state.
The plane is left with state cache state, if the particular plane
is not used in the subsequent frame by the same crtc. Reset the
plane cache state on plane disable and reset_custom_properties to
avoid this case.
Change-Id: Ic6d31567af23906e94c5404d1d366e030b9be199
Signed-off-by: Veera Sundaram Sankaran <quic_veeras@quicinc.com>
Static display usecase uses concurrent writeback path to compose the
layers and updates the primary display in the next cycle with cwb
output. Use LLCC_DISP scid for system cache in cwb path, to keep it
in sync with the legacy static display path. Use LLCC_DISP_WB for
the offline-wb path. Expose the writeback connector cache property
only when either or both the cache types are enabled.
Change-Id: I8ca4b14828a14ce0bde829136fb4baef272166aa
Signed-off-by: Veera Sundaram Sankaran <quic_veeras@quicinc.com>
Add sde hw catalog change to enable LLCC_DISP_WB system cache, which
is used for 2-pass composition usecases with offline writeback path.
Change-Id: Ic320b95a6699e59c62fed41f7fb88c484d98ffd0
Signed-off-by: Veera Sundaram Sankaran <quic_veeras@quicinc.com>
Avoid rotator code compilation if config is not
enabled.
Change-Id: I4793fadfe14820931df2fbcc53337fc8a15d6449
Signed-off-by: Dhaval Patel <quic_pdhaval@quicinc.com>
Currently code is locking the struct_mutex when accessing
the GEM object inactive list. This causes corruption of
the inactive list during stability testing.
This change uses the mm_lock mutex instead, as it is used
in the allocation and de-allocation paths.
Change-Id: I6384fd70e7ea5d7e3c2910c7670d152a61670dc1
Signed-off-by: Amine Najahi <quic_anajahi@quicinc.com>
Currently, when CWB system cache use case is enabled and multiple planes
are used to fetch the LLCC data only one SSPP is programmed correctly.
This change ensures that whenever the fb_cache_flag is non 0, the SSPP
system cache gets reprogrammed.
Change-Id: Ic90eaae207f6221efb1fc8749093d8b44e092e44
Signed-off-by: Amine Najahi <quic_anajahi@quicinc.com>
Sim panels are not working well with video mode, parse panel ack
disabled property to fix sim video mode identification issue.
Change-Id: Ife3b533d5a6db97618459dacf1f7ce8d3fc896bf
Signed-off-by: Yahui Wang <quic_yahuiw@quicinc.com>
Add line insertion support for sspp, this is used to support
display with external splitter. Line insertion logic checks
the difference between screen logical height and physical
height. If any difference is observed adds dummy and active
lines on screen.
Change-Id: Ieec322273df000a53fb39e05174c2d67c3c2da81
Signed-off-by: Rajesh kv <quic_kvrajesh@quicinc.com>
