During ssr, when powering down audio path and core vote fails,
it directly exits without disabling clock. After adsp is up,
it will enable both RX_MCLk and RX_TX_MCLK which causes
glitch on headset output.
Change-Id: I98d3cdbffa0a5ae1ac4064579a52a29b02d4ae3e
Signed-off-by: Deepali Jindal <deepjind@codeaurora.org>
SVA switch is not retain at VA_CLK when switch
between handset and headset mic sva. Update the
clock release logic during swr power event.
Change-Id: I52c5f7576426af2ff385a862da872e8d86959ecb
Signed-off-by: Meng Wang <mengw@codeaurora.org>
When requested clk is not default clk, it should not enable
VA_MCLk directly. lpass_cdc_clk_rsc_check_and_update_va_clk
will take care of VA_MCLK switch.
Change-Id: I602be7dcc0228fd2e6ecd7624a96663e89485bd0
Signed-off-by: Meng Wang <mengw@codeaurora.org>
Add ftrace log to debug NOC issues.
When writing/reading lpass codec registers, add vote_lock
to make sure clk is not disabled.
Change-Id: I1df924d6aefee2899f7e5008851c1c324dabf62a
Signed-off-by: Meng Wang <mengw@codeaurora.org>
When multi wsas are connected to wsa-macro and some registers
are written to wsa, swr broadcast mode is used. When closing
one wsa, it will also send the register write to the other wsa
and it should not get updated. The other wsa will be in bad
state.
Remove broadcast for wsa-macro to resolve this issue.
Change-Id: I4c788a213fdcd217861703a13d44c096fd9b632d
Signed-off-by: Meng Wang <mengw@codeaurora.org>
This change is to remove the group write so that both the WSA slaves are
updated with the corresponding values for DRE CTL register.
Change-Id: I1f9583ff1ca3988b78896087b2f8e7409e4796fd
Signed-off-by: Sairam Peri <peri@codeaurora.org>
During adsp SSR, after adsp is down, lpass_cdc_runtime_resume
is called in va-marco and fails. lpass_cdc_runtime_suspend is
not called 100ms later. After adsp is up and va-macro considers
lpass_cdc is resumed and not setting clk which causes wcd not
detected. Call runtime_suspend when vote fails to resolve
the issue.
Change-Id: Ice398d0168c5c67f6c98e3122af507ca74837175
Signed-off-by: Meng Wang <mengw@codeaurora.org>
Resolve warning log when hph pa mutex lock is destroyed before
unlock. Initialize hph pa locks as global lock and do not destroy
during SSR to resolve issue.
Change-Id: Idc5af793294f7fdc8dbcc17770f68fe2c46ab337
Signed-off-by: Vatsal Bucha <vbucha@codeaurora.org>
cooling of WSA/WSA2 is to reduce the digital gain.
the cooling callback should only be called when the WSA pointer
has not been initialized.
Also the adjusted volume of RX0 and RX1 need to be set separately.
Change-Id: I6aac0e7a3a3219e8b5c24d711a6c7773824827e9
Signed-off-by: Junkai Cai <junkai@codeaurora.org>
the dapm_mclk_enable flag has not been set back to false
when the actual mclk is disabled.
Change-Id: Ic04756b3dcd074887dd1e93f23cf31873abc1428
Signed-off-by: Junkai Cai <junkai@codeaurora.org>
When WCD AMIC is used and connected to SWR master port3,
DMIC clk div is updated by mistake. Update logic to update
DMIC clk DIV with new flag.
Change-Id: Iee01acf97f925ec54c8d189c13e63acca7ffc2f4
Signed-off-by: Meng Wang <mengw@codeaurora.org>
The digital gain will be adjusted lower than what userspace set
during playback if the device temperature reach the threshold.
Whenever digital gain is changed from userspace, codec will check the cooling
state and adjust the gain.
Change-Id: I52df0f96cf20b90a9bdad70b9c117eed82145fb2
Signed-off-by: Junkai Cai <junkai@codeaurora.org>
Sometimes link status is not connected due to tx_mclk_users
not being properly updated. This is due to tx_mclk_users
enable and disable not being protected by common mutex lock.
Add mutex lock whereever it is accessed to resolve issue.
Change-Id: Ibba208be1f2d3eaf63c49e434c2ae48bc3b5b2d8
Signed-off-by: Vatsal Bucha <vbucha@codeaurora.org>
Because of a HW limitation in DSP, while switching
RCG from TX MCLK to VA MCLK for SVA use cases
a glitch is seen on AHB bus leading to data
corruption in registers.
So, while doing a mux switch for VA RCG clock selection,
do not configure the muxsel register in HLOS as it is
taken care in DSP itself as a workaround for HW limitation.
Change-Id: Ie36ff239689e634f5c29ad03b343b95de2d12547
Signed-off-by: Meng Wang <mengw@codeaurora.org>
Check if clk is enabled before disabling it to avoid
warning log during adsp SSR.
Change-Id: I916af6f9efacfe3d08e0b05dcc0c6023944369d2
Signed-off-by: Meng Wang <mengw@codeaurora.org>
The PCM_RATE bit field in LPASS_TX_CDC_TXn_TX_PATH_CTL
ranges from 0 to 6.
In the current implementation of tx-macro, the value
read is mapped directly to the sample rate instead of
the indices. Change is to correct this.
Add the delay based on pcm_rate in va-macro as well.
Change-Id: I6cb7e58e71f2a25356608611f1dfed83171706f6
Signed-off-by: Soumya Managoli <smanag@codeaurora.org>
After ADSP SSR happened, toggle swr_slave_vdd before play to reset
haptics HW so that it can function properly.
Change-Id: I48bc07c923d1af2041c6c156c699e329084f0d34
Signed-off-by: Fenglin Wu <fenglinw@codeaurora.org>
Remove makefile for Rouleur codec.
Remove usage of shell command and update absolute path cmd
for AUDIO_ROOT.
Change-Id: I1589c688639892b7628914a3777632466949d000
Signed-off-by: Meng Wang <mengw@codeaurora.org>
MBHC extcon device is unregistered when adsp ssr happens and causes
kernel panic. Avoid unregistering MBHC extcon device in mbhc_deinit.
Change-Id: I69fa057a480ebadaf324ca1f61bf399c176e3b2d
Signed-off-by: Meng Wang <mengw@codeaurora.org>
Haptics module is supplied by HBoost regulator by default, it requests
voltage to HBoost regulator through hardware channel. Haptics module
can also be configured to use other regulator device, in this case, it
requires software to request the voltage from the regulator before
enabling the play. Add support for this.
Change-Id: I4a8305ff2732a92bc8be90bd3ed197fa643a101e
Signed-off-by: Fenglin Wu <fenglinw@codeaurora.org>
Update the slave-vdd regulator control logic to avoid unbalanced
regulator_enable() regulator_disable() calls. Meanwhile, correct
the jump label when bailing out from soundwire enumeration failure.
This helps to avoid the regulator_put() call in the device remove
process throwing a warning for a dangling regulator enable status.
Change-Id: I89157f5f9177db69bbbf6aedcc8e605c43a7584e
Signed-off-by: Fenglin Wu <fenglinw@codeaurora.org>
The number of HIFI FIR coeff will not be retained if power collapsed,
need to be written right before FIR_START is kicked off.
Change-Id: I034949eb7748f8b2e5b21445fa10f4f1df66a7bf
Previously code will not write coefficients if there are exactly 100 coeffs
in first coeffs write. Or if user update coeffs on the fly with one group
unchanged.
Change-Id: Id4e8af06dec6b247f4a79a797d5b61668fd1e7f4
Signed-off-by: Junkai Cai <junkai@codeaurora.org>
Reduce WSA8832 SKU DRE gain offset by
1p5dB same as WSA8830
Change-Id: I949bd78e2f4e935e1aba7ce0e2319418562e14ac
Signed-off-by: Laxminath Kasam <lkasam@codeaurora.org>
Update regmap default entries of spk protection
registers as per lpass cdc version 2p5.
Change-Id: I7c966eb3edbe9a9c065c03220ef2b9390b1fc723
Signed-off-by: Laxminath Kasam <lkasam@codeaurora.org>
