Found potential issues relating to uninitialized or out-of-bounds variables
present in codec drivers. Place checks to ensure proper ranges are used.
Change-Id: Ib68cba2413788a57237f1f18fc5ce5fb5c6bfb0a
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
For PBR and CPS ports, need the ability to customized slave
SWR frame OFFSET1 settings. Add similar method to WCD TX where
offset1 and lane_ctrl parameters are parsed from WSA device tree
and configured in SWRM.
Change-Id: Ib973ed93d9daa5ba02461a156e5b0a8c816d371e
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Update to 5.15 kernel dapm api.
Pin name no longer needs prefix as it is added in API.
Change-Id: I5c1378839f4c4d2aa70fb11706c5bb65d4eb0952
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Removed PA Mute, COMP Offset, Ext_vdd as they will not be used
in WSA884x.
Change-Id: I58ffd490c9929fa3388678d9ab7114207779191d
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Add set config function to validate and
set battery stack mode, rload and system gain
Change-Id: I075bf3cde6a9671a8d93f32aec43b941ea86f2ea
Signed-off-by: Shazmaan Ali <quic_shazmaan@quicinc.com>
Read noise gate mode from device tree,
set NG2 based on the register read or
set to idle detect mode
Change-Id: Id1e478ad230125d1e35229493cb0fbd6867c6a3b
Signed-off-by: Shazmaan Ali <quic_shazmaan@quicinc.com>
Boost current limit is now dependent on PBR and bat_cfg.
Add BOP2 VTH/HST initial settings.
Add OCP LOW VBAT ITH sel settings dependent on bat_cfg.
Change-Id: I235f4b75ee12e5f24d46fa0ebca67547997934e2
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Add PBR/CPS ports to debugging by adding logic to
is_swr_slave_reg_readable.
Change-Id: I9ef09ed90ccce2c696eaec7b1eed9c47a7e73f58
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Change PBR enable to be acquired from device tree.
Using system_gain, bat_cfg, rload, set pbr thresholds based on tables.
Table values are x100 to avoid kernel float issues,
truncate when converting to reg val.
Set pbr registers during initialization.
Rename WSA_8OHMS -> WSA_8_OHMS to match system gain naming.
Change-Id: I28985496e1da37ceeb8c9db6e17f4c48d37d11c7
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Previously we disabled all irqs by default and toggled them pre/post
playback. Update to leave them enabled by default and remove the toggling.
Also, leave the default values for edge/level triggering.
Change-Id: Iac96649fc0f33cbdf5a25f136cf577f7242db74e
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
If not using compander, allow for user to set pa gain
using DRE_CTL_1 register.
Change-Id: I45af5a64a5630ff1cd8410a66ed55914efb5a529
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Update WSA rload, system gain, bat_cfg to get from wsa_macro device tree.
WSA Bat_cfg change to read from VPHX_SYS_EN_STATUS reg.
Add device tree parsing for these params in WSA macro
and WSA driver.
Remove machine driver method of sending the parameters.
Add default_dev_mode (spkr vs rcv) from device tree for WSA.
Move code from spkr event to userspace controls or probe.
Change system_gain and affected params when switching between
dev_modes.
These changes simplify configuration data and code and allow
more registers to be written during bootup or before playback.
Change-Id: I79966c704adfac1bf2d85aa6519ea574764c7a8b
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
PA_ERR can happen during speaker path setup. Log the
error status in the interrupt handler and clear the error
status for next audio playback to resume properly on
the speaker.
Change-Id: I5800d9505a3036127097745aaa880b73b3e87f30
Signed-off-by: Sudheer Papothi <spapothi@codeaurora.org>
Signed-off-by: Meng Wang <quic_mengw@quicinc.com>
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Fix isense/vsense gain tables to correct values.
Mark ana_wo_ctl registers as volatile.
Move VBAT_THRM_FLT_CTL to init reg sequence.
Change-Id: Ie04f302719f08b35f1ef9807dff7993c31e3aa43
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
regmap_irq_chip->irq_drv_data is shared by all attached wsa
devices and point to last probbed wsa device. This will cause
interrupt handle issue. Update irq_drv_data per wsa deviece to
resolve this issue.
Change-Id: I013f546d7f1ca6077f0b14e875b135a27325f851
Signed-off-by: Meng Wang <quic_mengw@quicinc.com>
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
during devm_snd_soc_register_card(), the name_prefix can be set
if "sound-name-prefix" is provided in the DT nodes.
The original approach to set prefix would possibly cause ASoC
component probe failed if prefix has not set before probe is called
Change-Id: Ie78d042cda24b7d1d926223d476786e13d965ac7
Signed-off-by: Junkai Cai <quic_junkai@quicinc.com>
Interrupt from wsa884x are not handle as slave_irq is not set.
Add slave_irq for wsa884x to address this issue.
Change-Id: I82edb35b55f6a46d79bd96b7f0f4bfac58583860
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Conforms to latest hardware DRE documentation
Change-Id: Ia08b03f519697723e9e260451c5bc68b4b45724c
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Driver implementation for WSA884X.
Use new script to generate register files.
Modify register naming convention.
Add wsa884x-reg-masks.h and wsa884x-reg-shifts.h
Reverting copyrights to 2019 for wsa884x.h file
Change-Id: Ic3652d6138a2f62ba59a36d4307c732ab6e8db89
Signed-off-by: Shazmaan Ali <shazmaan@codeaurora.org>
