TLV targets support updating tx chainmask(soft-set) using
PDEV_PARAM_TX_CHAINMASK param. Update host enum accordingly to
use this for setting soft chainmask.
Change-Id: Ic5362fb8c79f07cbd83328b786b5930f75d2a084
CRs-Fixed: 2976914
Add APIs to extract AWGN information from the DCS WMI
interference event received from FW.
Change-Id: I4b2f9f4ef012553dac2a405dc7ac12aef9452354
CRs-Fixed: 2958675
First Requirement:
In case of WTC_BTM roam trigger reason, if FW reports rssi
threshold for 5G and 6G AP via wmi_roam_trigger_reason,
Host should print it in kmsg.
If wtc_candi_rssi_ext_present is set (1), It means fw
reports 5g and 6g candidate rssi (new firmware case).
If wtc_candi_rssi_ext_present is clear (0), It means fw
doesn’t report 5g and 6g candidate rssi (old firmware case).
Host use flag "wtc_candi_rssi_ext_present" to keep backward
compatibility.
Second requirement:
As per user space, value for scan mode in WTC command, is
like below:
0: no Scan, 1: partial scan and 2: full scan.
For NO scan case, FW sends value
ROAM_TRIGGER_SCAN_MODE_NO_SCAN_DISCONNECTION (3)
in wmi_roam_trigger_reason-> wtc_scan_mode. When driver receives
WTC scan mode as ROAM_TRIGGER_SCAN_MODE_NO_SCAN_DISCONNECTION,
it should print value as 0 instead of 3.
Convert WTC scan mode comes from FW to
wmi_configure_roam_trigger_parameters->scan_mode to make it
compatible to WTC command.
Change-Id: I8266460aac1272d345e4349c2ca52b4f9a745d4c
CRs-Fixed: 2965362
For some platform, ext2 service bitmap is not supported. So rate
limit the wmi ext2 service bitmap NULL error log to avoid
excessive console logging.
Change-Id: I383632669e4e4a59dd9e6e3ce82626a7cd3e42b3
CRs-Fixed: 2949180
Add functions to parse and extract wmi smart monitor
event received from target.
Change-Id: Ic18e3134b684c5f8e12839e997d628909a7e27c9
CRs-Fixed: 2969247
Currently the 6G edge channel feature is MCC specific.
Make the 6G edge channel feature common for WIN and MCC.
Change-Id: I723b6db1d74dca5a911eede4ec6e6167f6b3e6bc
CRs-Fixed: 2976871
New TLVs for MLO flags are introduced in peer assoc WMI
command. Add WMI changes to add these TLV in the peer assoc
command.
Change-Id: I366a96c973c3bedda03e4c370099ff809e0bd83d
CRs-Fixed: 2958851
New TLVs for MLO flags are introduced in peer create WMI
command. Add WMI changes to add these TLV in the peer create
command.
Change-Id: I38a129b30b366b6e3939231699f210d1bac362a1
CRs-Fixed: 2958849
Add parameter 'bool sync' for wlan_cfg80211_crypto_add_key()
to indicate whether or not to add key synchronously.
If it's set to true, wait until install key complete event
is received.
Change-Id: I9a69d486665fb3f65a5720ccfbfb638c09329418
CRs-Fixed: 2865832
As part of minidump enhancement feature, incorporate
wmi_command_tx_cmp_log_buffer data structure into the minidump.
Change-Id: I323971cc397b3ec710152c774462c85900acc603
CRs-Fixed: 2950790
Current FW implementation is not expecting MLO and partner link params
in vdev restart request. But host is sending these params as part of
vdev restart request. This is resulting in TLV count mismatch for vdev
restart request.
To resolve this, Don't send MLO and partner link params in vdev
restart request command.
Change-Id: Ied4572722c701ad7f53ac12727228a383e570433
CRs-Fixed: 2973256
New TLVs for MLO flags and partner link info are introduced in vdev
start WMI command. Add WMI changes to add these TLV in the vdev start
command.
Change-Id: Ic7d54c406f69346a6eedb43b1ebcf7266c448bd8
CRs-Fixed: 2958843
WMI vdev create is changed to incude mlo macdress as one of TLV.
Add changes in WMI vdev create send API to include this new TLV.
Change-Id: Ia13bdb8fbfc9f68d1e4c0209201f9acc4f575387
CRs-Fixed: 2958839
802.11BE D1.0 9.4.2.295c.4 Supported EHT-MCS And NSS Set
field specifies maximum 4 optional EHT MCS map, which are
20 MHz-Only STA, BW <= 80 MHz except 20 MHz-Only STA,
BW = 160MHz and BW = 320 MHz.
Therefore set WMI_HOST_MAX_EHT_RATE_SET to 4.
Also add a debug message to log peer_flags_ext.
Change-Id: I3d56998bf0de381ef147d6c0551dcdb7fd935f60
CRs-Fixed: 2963536
Set the SAE EAPOL offload support in resource config based on
WMI_SERVICE_SAE_EAPOL_OFFLOAD_SUPPORT bit received in service
bitmap from Firmware.
Change-Id: I878736105c070df514dfe8d989541227b3baad11
CRs-Fixed: 2957082
Add a new flag to indicate to fw that host will set the
nan_disable_flag for channels.
Change-Id: Ibf627bff77e1afb0849149a63981ca50476f6bfd
CRs-Fixed: 2949481
Current in wmi_rx_diag_event_work, rx diag event is processing
in a while loop, if there is continuous diag event comes from
fw, it is possible that it occupy the work queue, and other work
are not able to run.
Break the while loop so give a chance to other work.
Change-Id: I7af6d60aeb8c0524cc51d663658d5b17349daa60
CRs-Fixed: 2948839
Firmware generates wmi Rx diag events every few milliseconds,
and processing the same in system shared work queue may lead to
work queue lock-up detection. Hence, move Rx diag event processing
to dedicated work queue.
Change-Id: I10cdde317794e35bc6d10677ab76ea24a66e1880
CRs-Fixed: 2941409
When obss scan is enabled, FW will trigger scan periodically by
a timer. If a scan was triggered, FW need to access host memory
for data transfer. Occasionally, suspend may happen during one
scan, then FW is unable to access host memory and fw will crash.
So disable the obss scan before suspend.
Change-Id: Ie507da929a3701473cb57888e96e702e34d4c95a
CRs-Fixed: 2927239
When unregistering wmi handlers, the position of the
old handler is replaced with the last handler in the table.
But at this stage only handler was getting replaced, but
not the context. Hence, make sure to update the context
as well.
Change-Id: If90ea9d7663fb105e8e8ad7d7e6c70da20264e44
Fill peer assoc mlo params in peer assoc request command.
Also add definitions to the WMI_SERVICE_11BE.
Change-Id: Ied7959e022ee27f3bd698b84dc801491175f85b3
CRs-Fixed: 2934417
Add new reason code WMI_HOST_ADD_TWT_STATUS_SCAN_IN_PROGRESS
to handle add dialog rejection due to scan is in progress
at firmware.
Change-Id: I30c3d1096690bd0cb7a669206f087e006c23ea44
CRs-Fixed: 2923289
In the issue reported, the clear stats request from the
user space is timing out because event id from firmware is not received.
From the logs it is not clear whether host driver received it or dropped
it in the error path.
Add debug logs, to make sure cp_stats event id is received in the host
driver and also in error cases.
Change-Id: I634714281db4a82826791725ec38fd589334cde8
CRs-Fixed: 2926978
Extract the 11BE flags advertised by FW in WMI_SERVICE_READY_EXT2_EVENTID
and update the regulatory pdev wireless modes. The wireless mode is
currently represented as 'uint32_t' and all the 32 bits are exhausted.
To accommodate the new 11BE flags, change the data type of wireless_modes
from 'uint32_t' to 'uint64_t'.
Add a regulatory phymode 'REG_PHYMODE_11BE' in enum reg_phymode.
If the chip does not support 11BE phymode, FW advertises it via
WMI_REGULATORY_PHYBITMAP enum with a value of REGULATORY_PHYMODE_NO11BE.
Extract the phybitmap and store it in the regualtory
as 'REGULATORY_PHYMODE_NO11BE' bitmap.
CRs-Fixed: 2901260
Change-Id: I4ed3fc7c907b1f76e59efb347c747acea2a163b0
The firmware sends new reason codes due to roaming in
progress and channel switch. Add new reason code for
TWT session.
Change-Id: I3820ac74910e382f5a029de85f8e0915220bb996
CRs-Fixed: 2908384
Updated the EHT related variables as per latest fw cmn headers.
Address review comments from previous EHT gerrits.
Change-Id: I67cd58a4efcf3e06d2ca3b5570432593b1d80825
CRs-Fixed: 2902607
Add 320Mhz band width support and EHT capabilities information in
WMI peer assoc command.
Change-Id: Ie4ee95fb1790c828275e90b384b2bdc04efb3f29
CRs-Fixed: 2882054
EHT capapilities will be received as part of ext2 service ready message.
Update the structure as per firmware common header file and extract the
EHT capabilities field.
Change-Id: Id2dd170db4de588008742f95493d4d06a6431f1c
CRs-Fixed: 2857802
DHCP packet is received in the IPA exception path when
system is suspending. As part of DHCP packet processing,
WMI_PEER_SET_PARAM_CMDID is sent to FW after WOW is
enabled resulting in self recovery getting triggered by
host.
Fix is to do an explicit system wakeup if a WMI command
has to be sent post WOW enablement.
Change-Id: If1904a4fe5c861deed1b35071be10cb8cc8d6407
CRs-Fixed: 2890913
Add support to read the WMI service bit describing support
for the DCS AWGN interference detection mechanism.
CRs-Fixed: 2906768
Change-Id: Id062b9d63a09f522ac1efdbaf6731665fa438630
Add new TWT teardown status code to indicate firmware teared
down the TWT session due to concurrent connection established.
Change-Id: I9b0fb5c5179355f34bd07e91a996da3ade1c9ce8
CRs-Fixed: 2899575
Enable lower 6G edge channel ch2 (5935MHz) for APL2 6G regdmn
using a service bit WMI_SERVICE_ENABLE_LOWER_6G_EDGE_CH_SUPP,
which is not enabled by default.
Also, disable upper 6G edge channel (7115MHz) using another
service bit WMI_SERVICE_DISABLE_UPPER_6G_EDGE_CH_SUPP, that
is enabled by default.
Change-Id: Ia7cb7f7d3165375178adbe70adb19b8671496b6d
CRs-Fixed: 2885623
