Refactor the hdd_vdev_create() API to move device mode
based VDEV config to a new API.
The new API calls required configuration functions
based on the device mode.
Change-Id: I54c5412577b70d92652cb16fcfb10e4d69e6f6fd
CRs-Fixed: 3445149
The feature raises a pulses at specified interval in TSF time domain.
The pulses can be used to determine driver level latency between hosts
as they are operating in same TSF time domain.
Add ini "g_tsf_accuracy_configs" to configure parameters for TSF accuracy
feature to customize GPIO pins and interval.
Change-Id: I49609d5beba8043ac2ecc086e97b01d1e0b2d3f6
CRs-Fixed: 3277992
Enable source port learning for SAP to add AST entry for the
remote stations with next hop. The SAP should use 4-address
frame format for the remote destinations.
Add support to handle data packets for WDS destination.
Change-Id: I6002e6dd9c9bb2c7b2e4f85bf06156dbb7feebee
CRs-Fixed: 2997812
Replace blacklist/whitelist with denylist/allowlist in
qcacld3.0. and replace blm with dlm.
Change-Id: I9ba61dde3b3ea008ca3777448d1f8dab83d33ec1
CRs-Fixed: 3091211
Add "gEnableUpdateScramSeed" ini support to send
WMI_PDEV_PARAM_EN_UPDATE_SCRAM_SEED command to firmware
to enable OFDM scrambler seed.
Change-Id: Ie5c244a7ea418eec0af1f576e8521804ee85a665
CRs-Fixed: 3106348
Add support for sending WMI_REQUEST_THERMAL_STATS_CMDID
to request for the thermal stats via vendor cmd:
QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_THERMAL_STATS
This vendor cmd can either be used to clear the thermal
stats or to request for the thermal stats.
Added ini gThermalStatsTempOffset, which can
configure thermal temperature offset value for capturing
thermal stats in thermal range such as Thermal STATS
starts capturing from temperature threshold to temperature
threshold + offset.
If this ini is set to 0, then the events are disabled.
Also, add support for the FW event where the requested
thermal stats are sent in FW event
WMI_THERM_THROT_STATS_EVENTID().
The following attributes are sent in the events for every
level:
STATS_MIN_TEMPERATURE
STATS_MAX_TEMPERATURE
STATS_DWELL_TIME
STATS_TEMP_LEVEL_COUNTER
Change-Id: If8acdeec5bde33be346332ccaf39d78d0151203d
CRs-Fixed: 3016818
The purpose of the multicast Domain Name System (mDNS) is to resolve
host names to IP addresses within small networks that do not include
a local name server.
It utilizes essentially the same programming interfaces, packet formats
and operating semantics as the unicast DNS, and the advantage is zero
configuration service while no need for central or global server.
Based on mDNS, the DNS-SD (Service Discovery) allows clients to discover
a named list of services by type in a specified domain using standard
DNS queries.
Here, we provide the ability to advertise the available services by
responding to mDNS queries.
Change-Id: Id2a0468d49237c21062cfd1988e34903658cdad9
CRs-Fixed: 3008549
At present, duplicated thermal level change events are reported
on different mac with different pdev id from target. To report
the lowest pdev id's thermal level to avoid confusing the user.
Change-Id: Ia1f497ba1a1e0af946b87924de80b9fd39fe95e8
CRs-Fixed: 2976437
As part of WiFi ini clean-up FR, the ini parameter gEnableLPRx,
is identified as it is no longer used. Hence it can be deprecated,
and all instances of the config CFG_LPRx is removed.
Change-Id: I77f8f6839534c9a79cb3c7414582a5f31b87c561
CRs-Fixed: 2896027
Currently, there are two ini option 0/1 to disable/enable ILP
profiles in HW.
Extend this option upto 3 where
0 indicates disable
1 indicates perf settings
2 indicates max power saving
3 indicates balanced settings
Change-Id: Iff41b92b84309a670e2ad301ee72fb3caaba3df3
CRs-Fixed: 2886526
HW assist is a FW feature and it is enabled by default. But there is
no provision to disable/enable this feature based on requirement.
To address this, add INI param to enable/disable HW assist feature
in FW.
Change-Id: Icdc4a842be4d5c6991a785ee270f61ba87fcfe79
CRs-Fixed: 2841346
The SHO feature is used to offload beacon/probe response to HW.
So a new vdev param is required to enable/disable this feature.
Change-Id: I83d71d63485dee8d3433bf967a7feb56c1039f93
CRs-Fixed: 2815270
Add an INI to configure the wow-mode logging config.
So that,the fw would use this bitmap for logging when it
is in wow mode.
Change-Id: Ib2fbd0c5c9cc573b2f5b12dcdf06682c16550cb2
CRs-Fixed: 2810372
Handle firmware thermal stats event and populate the thermal
information to upper layer with vendor command event.
Change-Id: I83286367ab542c08a205a7636f3d03189b0500e5
CRs-Fixed: 2786623
gOclCfg is no longer supported and is being overwritten by
FW init config. Thus, remove gOclCfg ini from code.
Change-Id: Idf4d5280043a47650a68dc2159c386d94b0be5e9
CRs-Fixed: 2791392
ILP is a new hardware block which is used for PCIe powersave but
this can effect the throughput.
So to isolate the throughput issues, add ini param to
enable/disable this ILP hardware block using the ini configuration.
Change-Id: I19825af8598bbc2623542256e873367c2f3d29bd
CRs-Fixed: 2756587
Currently these params are sent to fw from hdd. By design, this
should be done by fwol component. Add fwol APIs to achieve this.
Change-Id: Ifcc67fe15e76a32c28819267b0639edae1032093
CRs-Fixed: 2665749
Currently there is no provision to configure OCL mode in FW during
driver bootup.
To enable this configuration add a new INI configuration parameter
gOclCfg.
Change-Id: I87c9131f5395c394f745e0170f0d9b3d1571d030
CRs-Fixed: 2644312
Make sure pointer wasn't dereferenced after being freed, so when
fwol_obj is freed, the function should return directly.
Change-Id: I69c23d2366b2ea0ff1caca9798bdc22063221a9c
CRs-Fixed: 2642567
Add new ini CFG_SET_SAP_XLNA_BYPASS under fw_offload to allow host
to pass config to FW. WMI_PDEV_PARAM_SET_SAP_XLNA_BYPASS makes the
SAP xLNA bypass configureable.
Change-Id: Ie501005f3035f14b3f23cdd260f401a6af81b798
CRs-fixed: 2632088
Add support to customize DSCP-to-UP map table and send the
customized map values to FW to update its corresponding
map table.
Change-Id: Ibe9704a90468c898dd2e60fdf83a271152f654ce
CRs-Fixed: 2616247
The mechanism of overriding ARP frames with AC will not work since
firmware always defaults to BE. Since this overriding is not going to
be supported, remove the arp_ac_category INI and all areas that use it.
Change-Id: I8bff251ded5842f3d0c95bb916eb98a051696ae0
CRs-Fixed: 2555459
To pass WFA 11N 4.2.25 case, it's needed to enable legacy mode
SIFS burst. So add INI to make SIFS burst mode configurable.
Change-Id: I740fe33a7ae0d9b558aa3b3aeee434f482ed24cb
CRs-Fixed: 2486171
Add configuration for gpio pin used to send strobe to wlan hw.
The host driver will latch the current time and toggle the gpio
to generate a strobe to wlan hw.
The tsf will be latched on detecting the strobe and it will be
made available in a register for sw access.
The wlan fw will read this tsf and report it to driver using tsf event.
Change-Id: I4365d97d22836ddbbd2bf9913d4f723e5a870369
CRs-Fixed: 2495152
Implement NON-QC platform TSF and TSF PLUS.
Implement gettime of PTP.
Implement TSF PLUS for SAP/GO
CRs-Fixed: 2399624
Change-Id: Id4f41a94256a8f035ae408c168c246569185c534
11k offload params bitmask is sent over the wmi command
WMI_11K_OFFLOAD_REPORT_CMDID. Its value is controlled by the ini
value "nr_offload_params_bitmask". The ini value got from the cfg
component during initialization is not correctly populated to the
sme layer resulting in zero values sent to firmware. This results
in 11k functionality failure.
Populate the 11k values to sme with values stored into fwol
component from ucfg_fwol_get_neighbor_report_cfg.
Change-Id: I8615745083cdab677bca8cbb76eb0902758a8a75
CRs-Fixed: 2397328
WIPHY features are populated before FW offload object is
initialized. Thus use direct config values for SAE and GCMP
WIPHY features.
Change-Id: Ic1b84c8709a0347fa22773786c0d5af32426e8fc
CRs-fixed: 2376983
If FW offload cfg object is not initialized before invoking
the ucfg APIs use the cfg defaults for the values.
Change-Id: Ibbfe22a833ab217f670058e504ec80971c98e049
CRs-fixed: 2376983
Move misc offload ini params to converged CFG component and
cleanup HDD ini config.
Change-Id: I14b3d95dc1577d02230168d305d1d1c4c7fef2fd
CRs-fixed: 2358489
Remove legacy cfg items definitions and related macros for the
converged CFG items.
Change-Id: I12944f50d68dafe989417dda777f29a6233c97a4
CRs-Fixed: 2340856
This is for adding support for FW offload component. It is responsible
to offload all the ini params that are needed by the firmware. To have
this component, the new files added are
components/fw_offload/dispatcher/inc/cfg_fwol.h
components/fw_offload/dispatcher/inc/wlan_fwol_ucfg_api.h
components/fw_offload/dispatcher/src/wlan_fwol_ucfg_api.c
components/fw_offload/core/inc/wlan_fw_offload_main.h
components/fw_offload/core/src/wlan_fw_offload_main.c
components/fw_offload/dispatcher/inc/wlan_fw_offload_public_struct.h
The fw_offload_main.h is to take care of the public APIs for the
component. The corresponding .c file implements the init/deinit of
the component. The fw_offload_public_struct.h is to define the public
structures needed. The ucfg files are for the APIs that can be called
from other components. The cfg_fwol stores the INIs and CFGs.
Change-Id: I4405b87e6dec15aa94146f8ec550078c3d03b1e6
CRs-Fixed: 2307837
