scan entry raw data length is not populated
during the duplicate scan entry generation.
Copy raw data length to new scan entry
while duplicating the scan entry. This api
is triggered as part of the get scan results
handler.
Change-Id: Ie59782fd437415552b7ae29c1b190e86d4b72d48
CRs-Fixed: 2186845
1. Enable scan command time out for all commands if not disabled
explicitly.
2. Remove QDF_BUG() for no serialization command buffers
Change-Id: I5357211ef6bc44f8ebd4b8acaa56a12f691fa46d
CRs-Fixed: 2175843
Move wma_get_buf_start_scan_cmd logic to common code in
ucfg_scan_update_params.
Change-Id: I4c9dcb48b4862ad10f64e260d87938251e270185
CRs-Fixed: 2180960
Support 11d for non-offload platform by maintaining
count of beacons encountered for each country code
and choosing country code with max votes as device's
country code.
Change-Id: I83b66e980854eded17e254386561fa32b1f8c4ac
CRs-Fixed: 2154048
When wide band scan is enabled, host configures all possible
channels with all possible phy modes. In his case if a scan
is invoked with 0 channels, target will end up scanning each
channel with all possible phy modes which increases scan time
exponentially.
If wide band scan is enabled and scan is issues with 0 channels,
configure target to scan all available channels only in 11A/11G mode.
Change-Id: I7c678ccf43c3238aacbfc59cc7e7bd19763453cc
CRs-Fixed: 2165025
Due to Rx sensitivity issue, sometime beacons are seen on adjacent
channel so workaround in software is needed. If DS params or HT
info are present driver can get proper channel info from these IEs
and set channel_mismatch so that the older RSSI values are used in
new entry.
For the cases where DS params and HT info is not present, driver
needs to check below conditions to get proper channel and set
channel_mismatch so that the older RSSI values are used in
new entry:
-- The old entry channel and new entry channel are not same
-- RSSI is less than -80, this indicate that the signal has
leaked in adjacent channel
Change-Id: Ie9dc26f938b58b0c5d071ce4f2ba02b8e7fd4f60
CRs-Fixed: 2180012
Pass back scan start request in scan events so that
handlers can know parameters used to start underlying scan.
Change-Id: I8ca3d55edb266677cc636228919656baa12b43d9
CRs-Fixed: 2159700
Adds logic to use default RSN IE fields if optional fields are not
present in IE. So if RSN IE doesn't contain AKM, group and unicast
cipher, use the default AKM(AKM_IEEE8021X) and cipher (CCMP).
Change-Id: Icabfb8b88b294e935908b249462a61124aa76268
CRs-Fixed: 2164531
Add bss_scoring_required in scan filter to enable/disable
scan results filtering based on scoring
Change-Id: I6c2c08a1cd959f1586e3e5bb7b63665f04c3a856
CRs-Fixed: 2165465
Beacon parse util API currently returns only one
scan cache entry to the caller.
Extended the beacon parse api to return list of
scan cache entries in scenarios like mbssid
Change-Id: Ia362cda4fdbc9955966696484869fee6ac2d0a22
CRs-Fixed: 2154753
Set passive dwell time to 28msecs for active
scan when bt a2dp is enabled and hw is not dbs
capable and when sta is connected on 2G band.
Change-Id: I44f2e3d98f2d7ddc52e4902ba989131c256da4ef
CRs-Fixed: 2160963
If the requester id is 0 or other invalid values,
the function scm_scan_get_requester_event_handler
will get unexpected handler.
Change-Id: I505e2e1a1bdc9cec57aaa0c28abadf28d228ba5b
CRs-Fixed: 2147555
Current scan cancel API frees scan request and notifies internal
scan complete event to registered scan event handlers.
Add option to wait for target scan cancel event before freeing
scan request.
Change-Id: I9ccd753595b3467f6b4e668e9cac876a1105bba0
CRs-Fixed: 2145484
When a beacon/probe resp is received the scan cache delete the
old node (N1) and adds a new node(N2) at the end of the list, If any
other process is using old node (N1), for some amount of time driver
will have 2 entry for the same AP. Now if driver again receive a
beacon/probe resp during this time, it end up deleting the older node
(N1) Again and thus making its ref count 0 and freeing it, even when
the process using old node (N1) hasnt freed it.
To fix this add a active state to the scan node, and mark it inactive
or logically delete the node as soon its deleted from ageout, entry update
or flush logic. Also do not use the inactive or logically deleted node
for any new operation. For this add a logic to return only active nodes in
scm_get_next_node.
CRs-Fixed: 2155538
Change-Id: I186d3a0b0540f0b572735e1d95239ddcd8c9bdc9
Add user configuration parameters to configure the number of
probes in scan request and probe repeate time during scan
Change-Id: I65a3734d8080d8adfe3e9ffa26905e6adc196197
CRs-Fixed: 2071697
Adds support to enable/disable scans for the psoc.
Also adds API to set and get the scan enable/disable status.
Change-Id: I2ebb6f9c7fffabef90e9f8c461bdf735e95f0db3
CRs-Fixed: 2124783
Add support to send BSS scoring params from INI to firmware.
Firmware will use these params to select best candidate during
roaming.
Change-Id: Iad0e71c770ac4f4c31ce3b19552f09fd27dc37bf
CRs-Fixed: 2121739
qcacld-2.0 to qca-wifi-host-cmn propagation
If no SSID are passed to NL80211_CMD_START_SCHED_SCAN cmd,
interface spec requires that an active scan is not needed.
Therefore a passive scan is now requested by cfg80211_sched_scan_request
for this case.
Change-Id: I1b1b9232ffb9d8d5c0bc9a1d75145d39c9fe9e6b
CRs-Fixed: 902092
Best candidate at first connection is a mechanism
to select best possible candidate for making Wi-Fi
connection based on the scan results provided.
Driver use Scan results to calculate score for each
BSS and select the best candidate to connect.
This enhances the user experience by connection
to better AP, based on certain parameters.
Change-Id: Iebb4ce009b23cae8ad7cbff83628e01633bbf3fe
CRs-Fixed: 2018585
Get the MAWC based NLO parameters from HDD/UMAC and pass them to
firmware via target/if
Change-Id: I76d7c8677ee73f9a3c54b7af4943b74a6b23323d
CRs-Fixed: 2064837
qcacld-2.0 to qcacmn propagation
Add changes to support PNO scan in connected state to find better Ap's
based on rssi threshold, band and rssi preference.
Change-Id: I0744297cc5269f0fe37613247c911102e293d8e9
CRs-Fixed: 2000342
Add timestamp parameter in scan event received from FW to aid
in calculating dwell time and overall channel switch time in
off-channel operations.
Enable foreign channel exit event inorder to be notified
by FW through the scan event.
Change-Id: I4ba028756ee7db35f6528c0554b09c73087184a7
CRs-Fixed: 2056330
Add changes to match FILS realm info present in FILS indication IE
with the connection info.
Change-Id: I1ed6081f3320ecee8f86f7d87597b343230923b3
CRs-Fixed: 2093637
qcacld-2.0 to qcacmn propagation
Add support to include only selective IEs in probe requests in
order to improve user's privacy.
Change-Id: I59cf4181f60f5b4cd87a32fbcf29160d87ca59c8
CRs-Fixed: 1105495
qcacld-2.0 to qcacmn propagation
Randomize probe request's source address and sequence number to
improve user's privacy.
Change-Id: I265f15476f1a23a268f159a44b6a3e4243fb9068
CRs-Fixed: 1105081
For Network Listen Offload and Perfered Network Offload, the fast scan
period is multiplied by scan_backoff_multiplier after max cycles have
occurred. Expose scan_backoff_multiplier to consumers of the WMI API,
so this parameter can be configured.
Change-Id: I478fb61cd096d3496205f4ff556e180dabf99b77
CRs-Fixed: 2035201
Scan command timeout value is 30secs and scan
cancel sync waiting time is 5sec due to this
in failure scenario scan timeout callback is
getting triggered very late and causing crash
in HDD.
Increase scan cancel sync timeout value equal to
scan command timeout value.
Change-Id: I7b98d26ac5d97039714a431030e47c463d3a670e
CRs-Fixed: 2048167
Add cancel scan sync api which will wait for scan to be aborted on
pdev or vdev.
Change-Id: Ie02eb981154856cda38ef70f42fdfcf82bb88961
CRs-Fixed: 2038092
Some user configured params are passed in filter during scan request.
Added them in scan defaults params and update them from user config.
Also use these params from scan def params instead of filters.
Change-Id: Ice2817c2f135289d7a3dbfa94c9c06263473ce2d
CRs-Fixed: 1095299
Add set/get API for max parallel active scans supported.
Max active scans allowed is set from ext service ready event
handler(8 as of now). Once FW announces this capability, FW
announce value must be used instead of hardcoded value 8.
Change-Id: I2af3a34c9f55f92c47aebbd12838a8d8fc6e3ba7
CRs-Fixed: 1095299
If elapsed time since last rssi update for a particular
scan entry is smaller than a thresold, calculate a
running average of the RSSI values. Otherwise last RSSI
is more representive of the signal strength.
Change-Id: I4cbecc8b6bfbb73c272544114b063b25c26e14fe
CRs-Fixed: 1095299
Currently driver is not initialize scan_f_chan_stat_evnt from
the configuration file which causes WMI_SCAN_CHAN_STAT_EVENT
to be always not included in the scan flag.
Add changes to initialize scan_f_chan_stat_evnt based on
ini configuration.
Change-Id: If6ea1d5c4efcc6d934daf00b537f25f0727ee55b
CRs-Fixed: 2031301
Few components don't have vdev object but still they want to
receive scan envents on underlying pdev.
Change ucfg_scan_register_event_handler and
ucfg_scan_unregister_event_handler to accept pdev instead of vdev.
Change-Id: I5a7ea78b1470b89637d418de6b984e5d20007c9c
CRs-Fixed: 1095299
Add changes to support P2P search using new scan module.
To support p2p search added vdev id and Broadcast mac address
in scan req also enable flags depending on scan req type.
Change-Id: I597f9f353da1b8b129f0ee16cd8eb7b7bbad2625
CRs-Fixed: 1095299
Add changes to initialize and de-initialize the scan database.
Also registers callback to TXRX module to handle
beacon and probe resp and convert it to scan entry.
Change-Id: Ic55e4fc6dc1b23bdf50165aea219e112dcad676d
CRs-Fixed: 1095299
