For multi link connection there might be the case where
rsnxe of the AP is not present on the link vdev.
This causes the link vdev alone to downgrade to 11ax
mode and assoc vdev is in 11be dot11 mode.
So for vdev with ML peer, the dot11mode is 11ax,
which causes abnormal firmware behavior.
Reject the partner link that doesn’t pass the security
check and validate the next available partner link.
if none of the partner link passes the security check,
proceed connection with single link.
Change-Id: I080557027180c0566a1c284a93fcc4b69c61a9c8
CRs-Fixed: 3581189
For mlo 5+6, 6 GHz band score is higher than 5 GHz, so 6+5 total score is
higher than 5+6, 6+5 is always selected before 5+6 even 6 GHz link score is
much worse than 5 GHz.
To fix it, calculate each link score for each MLO AP, if assoc link is
best link, add a boost score, then it can be selected first.
Update band weight and score for both SLO and MLO, select average of link
band score as MLO band score.
Change-Id: If0714fa94031d5746d89388917540f0e34086d86
CRs-Fixed: 3483850
Currently if MLO connection fails then connection is tried
with same link until it reaches to maximum no of trials but
connection is not tried with same assoc link by changing partner
link or with SLO.
So, when vendor roam score algorithm is enabled, add logic to try
MLO connection again by reducing number of partner links with
each retry till SLO connection is tried.
Change-Id: Ic0e3acd2198cfa0ed0ff893da6ae32d669d32a41
CRs-Fixed: 3521159
Host parse newely added vendor command
QCA_NL80211_VENDOR_SUBCMD_CONNECTED_CHANNEL_STATS and trigger
scan to get connected channel stats from FW in case of MLO
connection.
On scan done host sends scan done indication to upper layer
via QCA_NL80211_VENDOR_SUBCMD_CONNECTED_CHANNEL_STATS vendor
command.
Change-Id: I92dbd779c5fbdb1652a37cfa54c177bd13de4f28
CRs-Fixed: 3491060
scan db has intersected phymode. For BSS information via iwlist we need
non intersected phymode.
Change-Id: I62a4aea33a67ac12b5be5bcdd4a3fc4538056df9
CRs-Fixed: 3454700
1. Read the new service capability:
WMI_SERVICE_CCA_BUSY_INFO_FOREACH_20 MHz: Via this host knows
whether FW supports reporting of CCA busy info for each 20 MHz
subband of wideband scan channel or not.
WMI_SERVICE_VDEV_PARAM_CHWIDTH_WITH_NOTIFY_SUPPORT: Via this
host knows whether FW supports VDEV param channel width switch
with OMN/OMI notification or not
2. Register osif callback to send scan done indication to upper
layer
3. Add 2 new scan flags pause_home_channel and
report_cca_busy_for_each_20 MHz
Change-Id: I63d561a3c5f8e49a3ca42d956e6b630c63edeaf4
CRs-Fixed: 3460901
If PMKID present in AP expires, AP rejects the PMKID based association.
Current design is to clear the cache using BSSID/MAC address of link
in such cases to let a fresh SAE authentication to happen.
But host driver stores PMKSA with MLD address for ML BSS.
Adapt to the same and update PMKSA cache clear APIs to use
MLD address instead of link address.
Introduce new API which return the legacy address for non-ML
association and MLD address for MLO association of the BSS peer.
Use this API to get the correct entry from PMKSA cache to delete.
Introduce new utility API to fetch the MLD address from scan entry.
Use this API to get the MLD address of the ML candidate.
Change-Id: Id35a3937ba6649e8ba7ae8f849ac1ed2a9cc83f8
CRs-Fixed: 3453839
With the MBSSID IE, it has to generate the corresponding
beacon and probe response frames. Then handle the generated
frames per critical update feature.
Change-Id: Iff3fdb3a335a98d9ed7e51957885e2f161069807
CRs-Fixed: 3376521
The kernel-doc script identified some documentation errors in the
umac/scan folder, so fix them.
In addition, Change-Id I8340c6c654cf03f63aee9ed622e3db38056d714f
("qcacmn: Add API to access scan entry partner info") made an
incorrect copyright change, so fix that.
Change-Id: I629f5961ab0a284c70a47fc7d71fe81d5572ae25
CRs-Fixed: 3380633
In case of 4 LINK MLO we have link index as 0, 1, 2 and 3
so increase the MLD_MAX_LINKS to accommodate all links.
Also MAX RNR_BSS supported in 16vap 16 MLD across N links will
increase as:
For N(4 LINK) link MLO, Max RNR BSS will be given:
16(N_6G_LINKS) + N - (N_6G_LINKS) - 1(SELF_LINK) = 16*2 + N-2-1 = 33
Change-Id: If2e1755b8b99e83d8fe391220183921a70be61f5
CRs-Fixed: 3408516
Currently, if ACS_LAST_SCAN_AGEOUT_TIME is not provided by user then
the last_scan_ageout_time is updated to 0 and full scan is triggered
to find channel instead of using previous scan results, to avoid delay
use last full scan result based on ini "last_scan_ageout_time" value.
Change-Id: Ic38f0d3c83087dafde54b43762dd14deb7d02870
CRs-Fixed: 3404550
In api wlan_add_age_ie(), age ie is included in scan
result.
Remove api wlan_add_age_ie() as the bss age is
calculated using NL80211_BSS_SEEN_MS_AGO.
Change-Id: Ided2364ce7a52d942d29343455fc7ae511be9a18
CRs-Fixed: 3391276
Changes to handle dynamic link add for non-AP MLD.
Also add change to clear mlo cap for link removal of vdev.
Change-Id: I47e0bb77b7f32296e5745ffd53ce3a34ec35a63a
CRs-Fixed: 3346538
Fetch beacon/probe response with given mac address from scan db.
The frame can be used to fill bss descriptor in case of MLO
roaming where scan entry is derived from ML probe response of
assoc link.
Change-Id: Ie20b36c6619dd0e44d04d3bd8767c7dd09b053d5
CRs-Fixed: 3342439
To check the allowed dot11 mode of the VDEV, add new member to
struct vdev_mlme_proto hold this value.
Change-Id: I5bfbff0ab3056013a997744b8e9ce0b4d0a3d43b
CRs-Fixed: 3314403
Currently, structure tbtt_information_header and
rnr_mld_info don't have attribute __packed. When
fetching the value of bss_param_change_cnt, it
tries to align with byte and causes wrong value.
And these are OTA structures which should be moved
to file wlan_cmn_ieee80211.h.
Change-Id: I326e62e6f513c2b43fe08c278aa4b5a245d2d35c
CRs-Fixed: 3313710
Low latency SAP can come up on below two profile
a. Gaming
b. Lossless Audio
Scenario: LL SAP is present on 5 GHz channel and scan comes up
DBS: For both profile, allow scan only in 2.4 GHz channel
SBS: For both profile, allow scan on non low latency SAP
channel which are mutually exclusive.
Change-Id: I9d5832a457d08325b9e66099286ae3f18cdc66e1
CRs-Fixed: 3294607
Prensently for initial scan and roam passive scan dwell time,
the same ini CFG_PASSIVE_MAX_CHANNEL_TIME is used. This will
cause initial scan to have the roam passive scan value.
Decouple passive scan and roam passive scan ini parameter by
adding new ini param for roaming
Change-Id: I7bffb24a1e45548ed57492abc35e80958e9955ee
CRs-Fixed: 3272817
Based on the new requirement, add support to get requested
feature set info from different feature components.
Change-Id: I75c5a3062312b1124d21d1ae429a7c5a18d9f2d0
CRs-Fixed: 3262867
Add APIs to update and get the time at which scan
is completed in that channel.
Change-Id: I8c594b1881fc83daa88800eac9eac94c2e0df64a
CRs-Fixed: 3239359
Some operating class like 81, channel spacing is 25, need convert
channel width to 20 to get right score when select candidate.
Fix some code style issues too.
Change-Id: I15795d016cae74b7596a199ae2883aeababaf081
CRs-Fixed: 3250207
Select best candidate by mlo score algorithm.
Check bss mlo type first by mlo info, mlo config, partner frequency and
dbs/sbs cap, calculate candidate score for SLO/MLMR/EMLSR bss types.
For SLO case, same as before except:
Decrease percent of legacy band and nss to include 320M and 8x8.
Decrease max percent of congestion from 100 to 80 to include MLMR joint
congestion.
Increase weight of both band width and nss to 20.
For EMLSR case, same as SLO except adding EMLSR boost score.
For MLMR case, besides adding MLMR boost score,
calculate joint RSSI/band width/congestion score for combination of
scan entry + each partner link by new mlo algorithm, select partner with
highest total joint score as candidate combination, only activate that
partner link.
Change-Id: I640c6825d945caf5fab504a77717195c2eac0c93
CRs-Fixed: 3234912
Get mlo partner link freq from RNR IE.
Use band bitmap to filter mlo AP by band.
Force link on 2 GHz: mlo_support_link_band=1
Force link on 5 GHz: mlo_support_link_band=2
Force link on 6 GHz: mlo_support_link_band=4
Change-Id: Ib11dee117bef6121bbc455b62a2803138881a72a
CRs-Fixed: 3211974
Currently STA can scan and come up on 6Ghz or indoor channel if
hardware is non-dbs and SAP is present
As part of this change, do not allow STA to scan on 6Ghz or
5Ghz indoor channel for non-dbs hardware if SAP is present
Change-Id: I97759f8b2c6a1c460d90fbb797a0e64d2532797c
CRs-Fixed: 3186406
1. MLO requires a tbtt_info length of 16 octets. To support
16 MLDs, it requires to extend the current global_rnr cache
accommodating this new requirement in 11be MLO context.
Redefine MAX_RNR_SIZE accordingly.
2. Currently, scan-module is considering only upto 5 reported
APs in a RNR element. This will be ok pre-11be as the RNR info
is not used for connection. RNR info is required for link to
vdev matching for MLO based connection starting 11be. So, the
limit specified by MAX_RNR_BSS needs to be extended to be able
to parse upto 16 tbtt_infos from the RNR elements present in
beacon or probe-response. Some APs can advertise upto 16 co-
MLDs when 6Ghz link is involved in those MLDs.
CRs-Fixed: 3191537
Change-Id: Iff532f7ea4f0ebf21947e24edbfa1f28d2d92af3
Currently 6 GHz channel flags are not set for channels
present in the list from PNO scan request but are set for
all other 6 GHz channels which are added when either of the
two below conditions are satisfied
1. Userspace sets NL80211_SCAN_FLAG_COLOCATED_6GHZ flag
in PNO scan request.
2. At least one 6 GHz channel is present in the PNO scan req.
Add flags for channels in the PNO scan request based on the
scan_mode_6g ini configured similar to active scan request.
Add changes to remove the RNR flag for the channel if the
corresponding short SSID entry is present in the RNR db
Cache since if colocated SSID is different userspace doesn't
include corresponding 2.4/5 GHz channel information in PNO
request.
Change-Id: I22c4f7ecf65d4ab09dfbbe126aefe02f9145de42
CRs-Fixed: 3119113
These macros define the min & max time from TBTT, when the scan
dwell time starts. They can be used as a parameter to the scan
WMI command.
CRs-Fixed: 3154082
Change-Id: Ieca8acfd2e6897a8e45fafaaffd8f283f451d203
Currently in wma_chan_info_event_handler chan info
is updated based on gEnableSNRMonitoring. By default
gEnableSNRMonitoring is set to false, due to which
chan info is not updated.
Fix is to keep gEnableSNRMonitoring enbaled, so that
chan info can be updated.
Change-Id: I77a999d64fca093c8bc50e4532e659f37a3ac593
CRs-Fixed: 3109317
Fix partner link updation in scan entry when AP MLD has more than one
partner link.
Change-Id: I981f16c9de819390d6830ffe7a5b1e438a4f8403
CRs-Fixed: 3125861
First host checks below two things in PNO scan request:
1. Userspace sets NL80211_SCAN_FLAG_COLOCATED_6GHZ flag
in pno scan request.
2. At least one 6G channel is present in the pno scan req.
If any of above conditions satisfy, Host fills all remaining
(other than channel(s) present in pno scan req) valid 6 GHz
channel(s) to pno scan requests and set the flag
FLAG_SCAN_ONLY_IF_RNR_FOUND for each remaining channel(s).
Host sends this updated channel list via WMI command
WMI_START_SCAN_CMDID_param_tlvs->channel_list for pno scan
to firmware.
By this driver allows Firmware to scan 6G channels based on
RNR IEs only (for colocated APs reported by 2.4/5 GHz APs).
Change-Id: Ib6118c4525e9fbe233eb6a7e07a4a3345d486e8a
CRs-Fixed: 3103923
First host checks below two things in host scan request:
1. Userspace sets NL80211_SCAN_FLAG_COLOCATED_6GHZ flag
in host scan request.
2. At least one 6G channel is present in the host scan req.
If any of the above conditions satisfies, Host fills all
remaining (other than channel(s) present in host scan req)
valid 6 GHz channel(s) to scan requests and set the flag
FLAG_SCAN_ONLY_IF_RNR_FOUND for each remaining channel(s).
Host sends this updated channel list via WMI command
WMI_START_SCAN_CMDID_param_tlvs->channel_list for host scan
to firmware.
With this change, driver allows Firmware to scan 6G channels
based on RNR IEs only (for colocated APs reported by 2.4/5
GHz APs).
Change-Id: I2d9d2aac58bbc521b2476756d5919647bdc265cc
CRs-Fixed: 3103873
As requirement, concurrent mode, station 5G/2G scan need stop when AP
connected by peer station.
Condition:
STA + AP 5G (connected) + AP 2.4G skip 5G scan
STA + AP 5G (connected) skip 5G scan
STA + AP 2.4G (connected && 2.4G only) skip 2.4G scan
Others concurrency skip none
Add ini ch_list_trim_conc to enable/disable the feature. Default is
disabled.
Before send WMI_SCAN_CMD to firmware, call API
policy_mgr_scan_trim_chnls_for_connected_ap() to check if need
trim scan channel list. Which channel list need be trimmed
Change-Id: If4d1cf7347f757fb013ffcb4016e8e6f16859f42
CRs-Fixed: 3075068
Parse the per-STA profile IE and save the CSA, eCSA, Max Channel Switch
Time IE pointers in partner_link_info structure.
Change-Id: Icac75e3ad1f45bd5325c9144db7732684ebb4512
CRs-Fixed: 3087692
During SAE roam auth offload, update the beacon/probe response
frame coming from the FW via WMI_ROAM_FRAME_EVENTID into the
scan db.
When the bss info of the preauth candidate is unavailable in
the host/kernel scan entry, supplicant fails to determine the
proper SAE PWE config of the peer and the commit request fails.
Change-Id: I8537147104f30b74ffb2e87946f2e5f4b129f0df
CRs-Fixed: 3075460
Add LOW_SPAN_ACTIVE_DWELL_TIME and LOW_SPAN_PASSIVE_DWELL_TIME
macro support to keep all 2.4g/5g active/passive dwell time
same for low span scan mode.
Disable adaptive dwell to firmware so that firmware cannot
modify dwell time.
Change-Id: Iff05dd7b37a40226c61b28a1e59ea8aa8c57cb52
CRs-Fixed: 3076163
Currently, ML IE address update is missing while copying the beacon data.
This may result in illegal memory access when ML IE accessed from copyied
scan entry after original scan entry got freed.
To avoid this, update ML IE address in new scan entry while copying
scan entry.
Change-Id: I6161481cbd13573b8177f122f7d26d177cc07aaa
CRs-Fixed: 3052302
Fix compilation issues in MLO related code.
Add debug prints when generating link assoc response.
Add NULL value check.
Change-Id: Ie5951816ee39428c086ec91eaa6fc9cf598072b6
CRs-fixed: 3038725
