added 1msec delay before resetting FS cntrl, to ensure no
glitch at the start of VI feedback.
Change-Id: Ia9ae296f336e4deb4b8bedb718316a6772466a95
Signed-off-by: sarath varma ganapathiraju <quic_ganavarm@quicinc.com>
mark OTP_0 register as read register instead of read and write.
Change-Id: I666c388ba10cd00daf8ac902e0b05177503b1e26
Signed-off-by: Vangala, Amarnath <quic_avangala@quicinc.com>
System gain is miscalculated due to incorrect parsing of
device tree property. Correct the parsing logic of the
system gain device tree property.
Change-Id: I8c9c5198a139a69c2d5d9520a071123261b0581f
Signed-off-by: Phani Kumar Uppalapati <quic_phaniu@quicinc.com>
To enable datapath control for both HPH_L and HPH_R in
HPH sequencer. Which is used to fix the single channel
mute issues.
Change-Id: I1d9fb22255a2895fc2543ef5c3de02f0bdb9999d
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Move scp1_val and scp2_val into swr_device struct and
reset this two value after ssr.
Change-Id: I549f7438f034a2de0e556bd749594fbe5db2a21e
Signed-off-by: Yuhui Zhao <quic_yuhuzhao@quicinc.com>
updated sleep time to 80us from 20us after updating the
reset gpio pin from sleep to active state to give ample time
for HW to reset the pin state to active, to resolve the
component registration issue which is seen on stability
runs.
Change-Id: Icd13bf36d56906553352e595d07e478c23d1c13d
Signed-off-by: sarath varma ganapathiraju <quic_ganavarm@quicinc.com>
Clk vote is present after teardown the usecase. which
is impacting the power, in SND_PMD call swr disconnect
to avoid clk votes.
Change-Id: I94d1ab9dc19a62132033a5715d4212dbcb7d2b0b
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
update the codec digital RX clk rate to 9P6MHZ or
11P2896MHz depends on usecase.
Change-Id: I1c7167c10ef8bcdba876be265ef90d980f822d03
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Increase TDM interface max ch to 32 and max rate to 96kHz.
Change-Id: Icaabacff20bc08d98e0f4a6b47feaf8c09aee585
Signed-off-by: peizhong <quic_peizhong@quicinc.com>
Defer the probe when the msm cdc pinctrl driver is not prode.
Change-Id: I3ace42632601a8ef010363f23534471e99c0f827
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Optimize the power down logic of hph playback widget.
Change-Id: Ic6d085e70cb36cdc99bcbceddbce3aff2bc54ad6
Signed-off-by: Yuhui Zhao <quic_yuhuzhao@quicinc.com>
Remove swr clk set from analog side.
Optimize the debug log.
Change-Id: I8c3a946f1c64fd5d71fd5151c4c464d370b4ae8c
Signed-off-by: Yuhui Zhao <quic_yuhuzhao@quicinc.com>
Defer the probe when the msm cdc pinctrl driver is not
proded.
Change-Id: Ia6aaaca7c55b60b53008ffda0fc40e5db407cd2a
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Enable WSA RX1 mix path to ensure DMA is enabled
properly and data is consumed to drive right channel
using wsa mix path.
Change-Id: I2b0bc92eeaa82734254ceda96de39f20a761dc75
Signed-off-by: sarath varma ganapathiraju <quic_ganavarm@quicinc.com>
DRE is not disabled properly on targets where kcontrols are not exposed.
Add separate check for both SWR PCM and PDM data transport cases to
avoid having dependency on kcontrol.
Change-Id: Ifbd9aaa8213540c9cc19690ef70b30336580116a
Signed-off-by: Ravulapati Vishnu Vardhan Rao <quic_visr@quicinc.com>
Implement changes to make the driver compatible with bolero V2.2.
Change-Id: If2797a80f775c685ff2a6912de189b1d9b4906d0
Signed-off-by: Vangala, Amarnath <quic_avangala@quicinc.com>
Optimize the micbias usage set logic in tambora driver.
Change-Id: I77224f66f12e129f00708a531c1aab137aee7000
Signed-off-by: Yuhui Zhao <quic_yuhuzhao@quicinc.com>
Update config file to support tambora in Kalpeni.
Change-Id: I2190823f0b4cb9724080d92619a540f2b7bab9b2
Signed-off-by: Yuhui Zhao <quic_yuhuzhao@quicinc.com>
Request and release swr device wakeup votes in PRE/POST PMU and
PRE/POST PMD events to allow system enter low power states.
Change-Id: I8acd648bcc8e11cadda7254d7e5369155d9597c9
Signed-off-by: Phani Kumar Uppalapati <quic_phaniu@quicinc.com>
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
add support for both fsa and wcd usb AATC.
Change-Id: I0253faad734a433f5da93c34adfc4f9c2e37fa14
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
