All sde crtc's are virtual when they are created. Resources for the crtc
is allocated when crtc is enabled. All crtc's will not have same
capabilities because some of the dspp blocks have additional hardware
blocks. Change exposes additional dspp capabilities dynamically when
crtc is allocated the dspp hardware block.
Change-Id: I93e76a1335574e4ca30d9419ef6cc6e8149e2c3c
Signed-off-by: Gopikrishnaiah Anandan <agopik@codeaurora.org>
This change updates misr checks so that misr can be
configured during secure display session. In the current
code, misr_reconfigure flag is set only when accessing
through debugfs node.
Change-Id: Ic3a8316a4881551da3f0f340f6ef5ae3fbe4913f
Signed-off-by: Yashwanth <yvulapu@codeaurora.org>
Enhance logging in dp mst functions by adding connector ids to
better identify operations for different streams and add more
trace logs.
Change-Id: Iaf5c67105c7af82fc5118674ddde5aef2319a611
Signed-off-by: Rajkumar Subbiah <rsubbia@codeaurora.org>
Allow for overriding color processing features that normally uses
DSPP flush to use LM flush instead. This is required on targets
where some of the DSPP features have been tied to LM flush bits.
This changes adds a field in color processing node to track if the
override is needed and enables LM flush override for rounded corner
on target requiring it.
Change-Id: I584bd7b20dfc9fc7795b1b3b10e2f17a82945ce4
Signed-off-by: Amine Najahi <anajahi@codeaurora.org>
Add NULL pointer checks, before accessing the controller node.
Change-Id: If24c4fd4352ef5ab7642c817ddaa61a80b725c99
Signed-off-by: Vara Reddy <varar@codeaurora.org>
Fix the check for uneven split across LMs when destination
scaler is used and reject the use-case since this is not
supported by the driver. This can happen if an odd-value
for the horizontal width is being split across 2 mixers.
The existing check was broken since it uses pass-by-value
with a zero initialized value that callee tries to update
while iterating over the DS configurations. Use pass-by-
reference with the previous DS configuration, if available,
instead of just 0 values so the proper comparisons can take
place.
Change-Id: I529faf57e43fb471b28b4d222260ea4d37217d4d
Signed-off-by: Steve Cohen <cohens@codeaurora.org>
A new status register was added in DPU 5.x to INTFs to allow for
confirmation when the timing engine is disabled. This
functionality was controlled via an overloaded feature flag
which is used to enable INTF tear-check ops (also added in DPU
5.x). External displays support INTF_STATUS but have no use for
any tear-check functions. Separate these features so they can be
enabled individually on the interfaces which support them.
Change-Id: Ib8548619cb58bf19b7c02211ead7f33f52ffeae4
Signed-off-by: Steve Cohen <cohens@codeaurora.org>
In current driver, during system cache read mode update control flush
is invoked and there after commit thread is allowed to pick up next
commit. This can lead to improper frame flush and cause hangs or
underrun. This change add a wait till frame done after system cache
update to frame read mode.
Change-Id: Ic88e0bdbaaa1f45f825d40ecde4de9e8dea2efef
Signed-off-by: Prabhanjan Kandula <pkandula@codeaurora.org>
This change programs rotator sid value irrespective of
continuous splash since it is not configured from
bootloader. It also handles trusted vm support
to prevent accessing mdss hw register.
Change-Id: I80e286364286457545dfa236d629447241d98f95
Signed-off-by: Yashwanth <yvulapu@codeaurora.org>
A mode switch on a real monitor can be triggered by forcing the new
mode using debugfs and initiating an hpd_irq. Due to a missing
check for simulator state, the current driver calls the hpd_irq
callback for simulator even for a real monitor. This change adds
this check.
Change-Id: I13480eccd27eac2f9df3dd766d0445c0a5ea9b2c
Signed-off-by: Rajkumar Subbiah <rsubbia@codeaurora.org>
Introduce event logs for lutdma kickoff operations to make
LUTDMA usage more apparent in crash dumps. This will aid in
debugging and triaging LUTDMA issues.
Change-Id: I81b570dfc21b03627cdaf5d9693b786839716571
Signed-off-by: Christopher Braga <cbraga@codeaurora.org>
Add hooks to dump LUTDUMA debug bus status during dumping
of system debug status. LUTDMA debug bus can be accessed
from userspace via the "recovery_lutdma_dbgbus" debugfs node.
Output control of the LUTDMA_dbbus is managed by the
"reg_dma_dbgbus" node.
Change-Id: Iea011279dd3806f0f594102ce7a5dc018a8d2b7c
Signed-off-by: Christopher Braga <cbraga@codeaurora.org>
This change allows dynamic refresh trigger to sw trigger
and mdp intf flush. With this we can make sure that DSI
timing/clock update and mdp intf timings are updated in
one vsync.
Change-Id: Ic807f498e2e47be6dd0f1e11ff1fc0896a8ec758
Signed-off-by: Vara Reddy <varar@codeaurora.org>
DP MST driver registers bridge callback functions with the DRM framework.
mst_lock is used for synchronization of the mst bridge functions. These
functions call into dp_display where a session lock is obtained for
the display. HPD callbacks, on the other hand, are first handled by
dp_display. During these callbacks, dp_display takes a session lock
first before calling into DP MST driver layer. Currently, the DP MST
layer waits on mst_lock which can result in a deadlock.
This change removes the usage of mst_lock inside hpd callback functions
and just uses the session lock for synchronization.
Change-Id: I7ec338004eef43ac0f1e1f092463e9915cd60684
Signed-off-by: Rajkumar Subbiah <rsubbia@codeaurora.org>
This change resets the mixer swapping flag in crtc on a
seamless mode switch. In case of switching from command
mode to video mode it is a seamless mode on crtc, but we
disable connector and encoder. Due to this crtc fails to
reset the mixer swap since it is tied to dsc merge topology
on master connector. In transient state master connector
is not set and is set only after enabling the new mode on
connector.
Change-Id: Idebdabd642625b894100f62aeb62f11a9c101b03
Signed-off-by: Abhijit Kulkarni <kabhijit@codeaurora.org>
The lock used by the dp debug driver to synchronize the maintenance
and usage of the list of mst connectors is not initialized. This
change adds the missing initialization and deinitialization calls.
Change-Id: I4c24600b47c0b90c256caff45edaea07d082908d
Signed-off-by: Rajkumar Subbiah <rsubbia@codeaurora.org>
The simulation case uses dp_mst_sim_detect_port which
calls the drm detect port function after checking
the mst state. The non simulation case calls the drm
function directly.
This leads to cases in the disconnect path where
connectors are detected while being unregistered.
This solution merges the simulation and non simulation
cases by using the same detect port function, where a
check for mst state is performed before calling the
drm function.
Change-Id: I4a93001131beda54f8146bd50edc036924c94ab1
Signed-off-by: Sudarsan Ramesh <sudarame@codeaurora.org>
Currently driver uses wrong index to retrieve partial update
ROI during check phase. This can lead to ROI being 0 for some
of the CP properties.
Change-Id: I885132e8d29eaf1353ed079eb283f7ca3a3d63a6
Signed-off-by: Amine Najahi <anajahi@codeaurora.org>
UIDLE and QoS LUT configurationis might be different between
different frame rates.
Add this change to update UIDLE and QoS LUT according to frame
rate when DRM mode is changed.
Change-Id: Ia16a963e185b911b7dd11e81a26cab732c2b185c
Signed-off-by: Lei Chen <chenlei@codeaurora.org>
When DRM property objects are created, the DRM framework attaches a
dellocator which can eventually free the object when the last reference
is removed from it. The framework can only do this before the driver is
registered. If a property is created after the registration then the
framework is unable to attach a deallocator causing a memory leak during
tear down.
The current DP driver creates a new colorspace property whenever a
new dp connector is initialized. It creates a base connector at probe
time prior to registration. But then it also creates new connectors,
post registration, whenever a new MST dongle is attached to the
topology, causing memory leaks.
This change limits the property creation to the base connector and
attaches the same object to MST connectors to avoid memory leak.
Change-Id: Ib97dc7aac260b4f3f96c1097f58bd276c68501f8
Signed-off-by: Rajkumar Subbiah <rsubbia@codeaurora.org>
The panel regulator votes are added by default during
dsi probe to make sure sync state driver doesn't disable
these regulators for cont_splash use case. These regulator
votes need to be removed when cont_splash feature is
disabled. Add a new connector API to handle this.
CRs-Fixed: 2734419
Change-Id: Ie54c8f246877a042afacddaeae8b90440652116f
Signed-off-by: Chandan Uddaraju <chandanu@codeaurora.org>
Enable DP controller hardware feature to modulates the
data drain rate between DP and INTF to reduce chances
of MDP Underflow or DP Overflow.
Change-Id: I7214a2fff957ae35b31c660bafa1d0141eb50680
Signed-off-by: Amine Najahi <anajahi@codeaurora.org>
