Primary and secondary displays should have first priority
when reserving lms. Static reservation can potentially block
higher resolutions for the required displays. This patch gets
the layer mixer requirement for primary or secondary display
if available. It reserves those layer mixers dynamically
for the respective display when connector is registered.
Change-Id: Id69dac4c72d6b20008049f4aeb71c0f97d0a426b
Signed-off-by: Nilaan Gunabalachandran <ngunabal@codeaurora.org>
SDE driver triggers the frame and waits for the
ctl_start interrupt for command mode display. This interrupt
provides confirmation that hardware has picked up the
frame. Retire fence signaling is associated with
this interrupt and it is sent at the rd_ptr interrupt
after ctl_start. Due to lut dma delay, ctl_start interrupt
may be trigger before rd_ptr or after rd_ptr. SW manages
this complexity and handle retire fence for different cases
with 500us threshold logic.
This change replaces the ctl_start interrupt with wr_ptr
interrupt by programming it to trigger at 1st write line
count. This is guaranteed to come every time and it is close
to rd_ptr interrupt. That allows retire fence trigger at
wr_ptr interrupt and simplifies the SW logic. CRTC commit
thread would be held slightly longer with this change
as the wr_ptr is always close to rd_ptr and after
ctl_start.
Change-Id: Ic47a8f82c854b4aded0d70c95af853b28a68ffd6
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
This snapshot ports changes from 4.14 to 4.19 into
the msm and sde layer. Snapshot was taken as of
commit 0f8fb25421ff ("cnss2: Add device version to
SOC info structure").
Change-Id: I59b799a78319c2db6930a2a10bc38976f8c09898
Signed-off-by: Samantha Tran <samtran@codeaurora.org>
Each mode_set call makes sure that previous frame is triggered
and triggers the esd check if there is pp_timeout. This may
lead to deadlock between crtc commit and event threads. Crtc
commit thread acquires the rc_lock and triggers the flush_thread
API on event_thread. Event thread again tries to acquire the
rc_lock to wait for frame. This can be prevented by avoiding the
pre_kickoff call from esd_failure notification if it is generated
through pp_timeout.
Change-Id: I561fef0345976ab0cae61aab6718214c47fa1393
Signed-off-by: Dhaval Patel <pdhaval@codeaurora.org>
Fix possible out-of-bound access and NULL pointer
dereference in SDE and PLL driver.
Change-Id: Ic5c34b3b4c3e983413a0351c38206cf3f3ab3b1f
Signed-off-by: Samantha Tran <samtran@codeaurora.org>
Log ping-pong current line count during ctl-start
and rd-ptr interrupt. This will help in debugging
ping-pong timeout issues.
Change-Id: I58185330fe9e8a64f48d6da60c974b23a9e68b44
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
Reduce the log level from error to debug for invalid
master encoder in encoder restore path during idle
power-collapse. This would avoid unnecessary logging
when concurrent writeback gets enabled after a
power-collapse event, the restore happens based on
encoder_mask attached in the crtc before the actual
enable call for the cwb encoder.
Change-Id: I54cd7de62f1a9030f68a963c8ed27ff098302e04
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
DSI display may support video mode and command mode both and it may
support transition between these two modes.
This change adds seamless transition between these two modes for DSI
display by avoiding crtc enable/disable and panel power on/off
during modeset.
Change-Id: Id7ddaef7d1f0f7cc7d52283755bad53a246adec6
Signed-off-by: Lei Chen <chenlei@codeaurora.org>
This change fixes the destination scaler atomic check
to support PU with CWB disable without an additional
frame in between. It also fixes the destination height
calculation.
Change-Id: I93ae8471d2db0b4e2574d18a873d4d4e180cbcbb
Signed-off-by: Lakshmi Narayana Kalavala <lkalaval@codeaurora.org>
Add runtime_pm ops support in drm driver instead
of direct sde_power_resource_enable/disable call.
It allows drm driver to use runtime pm refcount logic
to track the resources instead of custom implementation.
The change also removes the NRT_CLIENT support from
sde_power_handle code to simplify it further.
Change-Id: Ib14692dca5876703d0a230da2512d731b69b8ebb
Signed-off-by: Dhaval Patel <pdhaval@codeaurora.org>
Check if cur_master encoder exists before using the variable in
sde encoder. This will avoid possible NULL dereferences.
Change-Id: I003386cba392a0027f7e9e8441fd4671b57b9a03
Signed-off-by: Nilaan Gunabalachandran <ngunabal@codeaurora.org>
This change brings msm display driver including sde,
dp, dsi, rotator, dsi pll and dp pll from base 4.19 kernel
project. It is first source code snapshot from base kernel project.
Change-Id: Iec864c064ce5ea04e170f24414c728684002f284
Signed-off-by: Narendra Muppalla <NarendraM@codeaurora.org>
