Add support for WMI_TWT_NUDGE_DIALOG_CMDID and
WMI_TWT_NUDGE_DIALOG_COMPLETE_EVENTID.
Change-Id: I9d4bf1061f6f08479967619ce50d2756c062f55f
CRs-Fixed: 2825138
Support new firmware thermal level WMI_THERMAL_SHUTDOWN_TGT
to indicate target over heat and need to be shutdown completely.
Change-Id: Icdb8aab9fe7b8914681cc46a4ccb5579781c587d
CRs-Fixed: 2835410
Currently, Stats request commands are sent over qmi right from the
target suspend request is sent to FW. This is leading to a crash in
FW since it is trying to access PCI when it is in suspend state.
To address this, send stats request over QMI only after the ack is
received for the target suspend command.
Change-Id: Id7a79d52740916f66476bf911e571c0ff466c7d3
CRs-Fixed: 2838737
Introduce wmi_validate_handle() with the caller function name
embedded in it to validate the WMI handle and log incase
of error. Calling functions can avoid logging in case
wmi_validate_handle() returns -EINVAL. This reduces logging and
thereby memory foot print.
Change-Id: Ie0a6a84ffad6e5cf2da8f547c7209dc77cdf5729
CRs-Fixed: 2838960
Currently, Rx diag event work is not being flushed during idle shutdown.
This may result in use after free access if the scheduled diag event work
gets the chance to execute after driver modules are closed.
To address this, flush diag events work during idle shutdown.
Change-Id: I348e80d2c86a5e070f0fb67d66b758529fede76c
CRs-Fixed: 2838020
Currently QMI message length is not being validated before
handling QMI event. This is resulting in illegal memory access
when QMI message length is invalid.
To address this, discard QMI events with invalid length.
Change-Id: Ia9f04bcb4fa3b365cbbf2be8885a8d30f78f8f10
CRs-Fixed: 2839277
FW memory allocation depends upon important resource config sent from
host during wmi init. Hence, log these important resource config parameters
sent during wmi init.
Change-Id: I5e187b905716a5a2c1767bc4b081f54034994653
CRs-Fixed: 2839119
The bcast twt functionality may need to be enabled separately
for requestor and responder roles. Enable such configuration
by looking up WMI service bit support from target:
wmi_service_twt_bcast_req_support
wmi_service_twt_bcast_resp_support
Change-Id: Ibc91173c23cf69f0d248af27d61c77bee3e8f48a
CRs-Fixed: 2828720
Add support to view station's peer RSSI value in auth and assoc request
packet by extracting rssi from probe request and passing it down to
FW in the auth request and assoc request mgmt frames.
Change-Id: I92f714ed815ab8c77f6a6b7df3363dc96f1119bc
CRs-Fixed: 2832982
Extract btm response and initial roaming stats coming
from FW through WMI_ROAM_STATS_EVENTID event as
wmi_roam_msg_info_tlv_param.
Change-Id: I9a9b768d09a45ba70066cacb4aa420a90a39a76d
Crs-Fixed: 2826323
The regulatory structure which contains country and regulatory domain,
needs to be expanded to include 6Ghz superdomain.
Make changes in the regulatory component to send the 6G super domain
set by the user, to the target.
Change-Id: I84b96cd74012e33d464d98675158c9cd5eabff4e
CRs-Fixed: 2802131
Currently, there is no INI parameter to control NAN feature in 6GHz
frequency band. Because of this, there is no provision to disable the
NAN in 6GHz when there is no requirement.
To address this, add INI parameter to configure NAN feature in 6GHz.
Change-Id: Ibc653d6241d176f7fb75f18d2886175231ad71cc
CRs-Fixed: 2817925
FW diag events will be dropped when number FW diag events pending for
processing is reached to configured RX_DIAG_WQ_MAX_SIZE value. Add a
log when these diag events a getting dropped for debugging purpose.
Change-Id: Ifc303991bdf274fa7426794eaf71517722e9f386
CRs-Fixed: 2824458
Currently, FW diag logs, management frames and stats responses are
processed in worker context. Because of this, there is a possible
out of memory scenario when there are huge number of diag events
waiting in work queue.
To address this, process diag events in a separate worker thread and
set the limit for the number of diag events that can be queued in
work queue.
Change-Id: Ie6e5b905a3b591cf724cd6b024bec0612f9e2e0c
CRs-Fixed: 2818013
Skip wmi sequence check during SOC stop and enable after
initializing wmi handle. It is required to skip sequence check
during soc stop as the endpoint flush is preceding CE flush.
CRs-Fixed: 2813341
Change-Id: Ieb821483e9786471d033773dc2365ab456345f83
Swap each word of beacon and mgmt frame for big endian platform.
This is needed since copy engine swap is enabled but beacon and mgmt frame
needs to be given in same order to FW in order to get transmitted in the
intended network byte order.
Change-Id: I09290f3beef5f0cde33a5543c2778473b35d232c
The event WMI_ROAM_STATS_EVENTID is received after
every roam, once the roam synch complete is sent by the host.
This event contains details regarding the btm response.
This helps to debug the scenario when roam failure happen.
Print the info received related to roam scan type & roam status
info into kmsg.
Change-Id: I7c01d482e3152dfbf500dba97001c328f39564de
CRs-Fixed: 2812515
Below optimizations can help to improve 6g scan,
1. RNR-only: Consider only 6g RNR(PSC and non-PSC) channels found
while scanning 2g and 5g bands, as the 6g APs are likely to
present in RNR channels.
2. Duty cycle: There is a chance to miss the standalone 6g APs as
they don't advertise RNR IEs. So, instead of optimizing all
scan requests, we can consider to do a full scan with duty
cycle(n) where optimization is skipped for every nth full scan.
The full scan requests 1 to n-1 are going to be optimized as
per RNR-only policy.
Driver shall maintain a scan count to track the full scans and
decides whether to optimize the scan (scan count 1 to n-1) or
send it as it is(scan count n) to firmware.
Change-Id: I35b31e900b74dbcd7791f4c2fcfe87b3c629758b
CRs-Fixed: 2806409
Firmware advertises the service capability bit
WMI_SERVICE_SCAN_CONFIG_PER_CHANNEL when it supports per channel
scan config flags. Get this and cache in psoc.
If firmware supports WMI_SERVICE_SCAN_CONFIG_PER_CHANNEL, it uses
the upper-12 bits(bit-20 to bit 32) of channel_list for flags and
lower 20-bits(bit-0 to bit-19) for frequency. If firmware doesn't
support it, then channel_list holds the frequency value only.
Fill the flags and frequency accordingly.
Change-Id: I88a6f29f61e1ecea75bc5574cadcbbfbb7f8b188
CRs-Fixed: 2806405
Add the WMI command WMI_DBGLOG_MOD_WOW_LOG_LEVEL to enable
debug logs while in wow mode.
Change-Id: Ia1902d989964a5e35f590a075a2de64a9f66d5b7
CRs-Fixed: 2810326
Since new rso ROAM_OFFLOAD_V1 path is enabled, remove
the old rso path code for wmi related files.
Change-Id: Ie519ca7fac2d721f87a4c9bd11507cd83ddfb504
CRs-Fixed: 2810241
Add bus related info in hif layer in order to get bus status
when hang issue happened.
Change-Id: If922e0892e0f65de778b9696bbc56fc63c25c169
CRs-Fixed: 2801350
Currently, NDP app info length is not being validated with max NDP
app info length. This may result in buffer oveflow wile accessing
NDP app info received from the firmware.
To address this, validate NDP app info length before accessing NDP
app info
Change-Id: Ifddf1afca7ecf2585e8eb450864d9ba127238f6e
CRs-Fixed: 2795961
Add host data structure and api declarations
corresponding to peer response event and register
WMI_PEER_CREATE_CONF_EVENTID in global wmi event_ids.
Change-Id: I143a4a85d079cc113397348512b0d86f500cae5b
CRs-Fixed: 2797197
Add b_twt_enable variable to enable/disable broadcast TWT in
wmi_twt_enable_param structure and use FW macro in WMI layer
to enable/disable BCAST_TWT in TWT_ENABLE cmd.
Change-Id: I892e922dda14d16019f3f433f885d1eb5b7169fc
CRs-Fixed: 2793360
For QMI events, recevid QMI event length is used to allocate wmi buffer
using wmi_buf_alloc. The received QMI event length includes WMI head
room and wmi_buf_alloc also try to reserve WMI head room again.
Because of this, WMI buffer allocation is exceeding max WMI msg length.
To resolve this, use length of the received actual WMI msg to allocate
WMI event buffer using wmi_buf_alloc.
Change-Id: Icd259988c4b1091580a35aaf2c3fabc606e0f2a9
CRs-Fixed: 2786326
Many firmware do not send wmi_ext_service bitmap in wmi_ready event
so the ext_service_bitmap will be empty in such cases. So the condition
in the is_service_enabled_tlv to check for wmi_ext_service bitmap
and return false is wrong as wmi_ext_service bitmap support is not
necessity. This condition leads to incorrect behavior in cases when
firmware do not support wmi_ext_service bitmap as is_service_enabled_tlv
returns false for every service.
Fix the above failure by addition of condition check for wmi_ext_service
bitmap only when wmi_ext2_service bitmap is supported by firmware.
Change-Id: I94d0b65e640d44f41d14de889955a6d6330e88b2
CRs-Fixed: 2786491
Reset the WMI sequence counter after FW recovery to avoid
false assert due to CE pending packets freed in htc layer
instead of WMI completion handler.
CRs-Fixed: 2787424
Change-Id: I109ff56655e5fb428aca637e6420efed5943b3f7
As part of removing gOclCfg ini, remove code used for it that is
no longer needed.
Change-Id: I00c32988cb3b852381be9810377aeefdd22454db
CRs-Fixed: 2791469
log level for some frequent prints is set to info those
logs would be present in dmesg as well as driver logs
and System performance may get affected due to excessive
logging.
Avoid redundant logs which may affect system performance
and change default log level to debug.
Change-Id: Ic8669c2d7158200e5881bc1ffd15079c8d24af68
CRs-Fixed: 2794518
Add WMI command buffer address information(DMA/Physical addr) to
the WMI TX completion logging. This will help in debugging issues
when HW DMAs copies data from a different location than the one
configured.
Change-Id: I60586b865a97e7ff88e48606806ec151321ff0aa
CRs-Fixed: 2789492
Send unified ll_stats and get_stats request over qmi based on INI
configuration.
Change-Id: Icc43352c1ba19696148619100ee27fda4d5ffb41
CRs-Fixed: 2791043
Currently driver can handle only one radio stats event,
if the size of radio event exceeds more than the size which
can be accommodated in single WMI event in that case FW needs
to send multiple radio stats events.
Add support in host to send WMI capability to indicate FW
that host supports the multiple radio events.
Change-Id: Ifb89419715c87959095c0c88a23c8dd650d456e7
CRs-Fixed: 2783251
