Modify wmi_nofl_info_high definition to print only if
QDF_TRACE_INFO_HIGH_NO_FL debug level is set.
CRs-Fixed: 3570322
Change-Id: I879a9d917ff698aeb6b3e53a85c765a74a902b36
Add support to handle WMI_ROAM_SYNCH_KEY_EVENTID.
WMI_ROAM_SYNCH_KEY_EVENTID is received after roaming to 3 Link
MLO AP when standby link is supported.
Add changes to register handler function pointers and parse
the event.
Change-Id: Iee17560f9f1f3242ef512a550764a9c64319b67f
CRs-Fixed: 3571673
Prepare and Send WMI command to fw to set the rf path. Also, add module
ID for rf path switch for qdf log prints.
CRs-Fixed: 3568221
Change-Id: I7ef0ffe66eaed837424699641d3e5b8537cd0304
Once the FW sends the link switch request to host handle
the request from scheduler thread and send confirmation
back on completion of link switch process with status of
link switch (success/failure).
Add new serialization command type for link switch.
Introduce flags to get the current state of link switch
request, set the state to idle when no link switch in
progress or once the current link switch is completed.
Access to state is protected with MLO dev context lock.
Implement various helper API to:
a) Transition link switch to next state.
b) Get current state of link switch.
c) To check whether any link switch is in progress.
c) To check whether link switch is happening
on assoc VDEV or not.
Introduce a new VDEV flag to suggest the VDEV is in
link switch process and also implement helper APIs to
set/get/clear this VDEV flag.
a) The flag is set at start of link switch, once
the FW request params are validated and before
proceeding for link switch disconnect on VDEV.
b) Clear the flag once the Link switch confirmation
is sent to FW.
Validate the link switch request params:
a) IEEE link ID's received.
b) Check if new connection is part of MLO connection.
c) Check if VDEV is MLO STA VDEV or not.
d) Is VDEV in connected state or not, that means
VDEV is not in transitioning state due to disconnect.
e) Check if any link switch in progress on this MLD
f) Current link ID of VDEV equals the FW params.
If validation is successful, serialize the link switch
command and in the serialization activation start the
actual link switch process.
Change-Id: Ie582650541054c8cf39aaa8316e86a7a40256a15
CRs-Fixed: 3556422
Extract aux device capability from service ready ext2
event, and report such info to wma/mlme/hdd.
Change-Id: I888624fd3443118ba66fadd7a40fcce4f4b5d521
CRs-Fixed: 3549753
Define and initialize new WMIs for v2 ATF.
Rename send_set_atf_cmd to send_atf_peer_list_cmd which
is more appropriate.
Change-Id: Icab17703a4ccea8e2b859bf6a18387fbd2234226
CRs-Fixed: 3542065
Add support to send link recommendation command. This will
allow the user to pick the link that they want to utilise.
It is now the WFA prerequisite for AP.
Change-Id: I7d4459a65ce599aa5f674a3cc4a54185595ede40
CRs-Fixed: 3534151
Add WMI command support to force power save on all the
active MLO links for a defined number of beacon periods.
Force power save allows the firmware to suspend STA links
for X beacon periods and remain asleep even if the AP
advertises TIM as opposed to regular power save mode where
STA links wake up if the AP indicates that it has buffered
data to send.
Change-Id: I381a107f3f5f479b0eee4f526a49d6fc886aced0
CRs-Fixed: 3509543
Firmware sends NDP_HOST_UPDATE event as an immediate response to this
request and starts cleaning peers one by one. Once an NDP session is
ended (indicating NDP_END to peer + internal cleanup), firmware sends
NDP_END_IND to host.
Currently, host driver stops the wait timer and change state from NDP
end to disconnected upon receiving the NDP_HOST_UPDATE. But firmware
might still be in the process of NDP cleanup. As the NDP_END_ALL
context is unblocked, driver may send NAN disable request to firmware.
This may cause inconsistency in firmware state machine and firmware may
drop the ongoing NDP_END request. So, peer doesn't get the NDP_END frame
in such cases.
Unblock the NDP_END_ALL-wait call only upon last NDP_END indication to
avoid such issues. This change moves the major functionality of
NDP_HOST_UPDATE processing to last NDP_END indication. Cleanup/remove
the processing of NDP_HOST_UPDATE as it's not needed anymore.
Change-Id: I00e73d211de4626484ffb2483c00adce1a7302c1
CRs-Fixed: 3512923
Add code changes to handle new wmi_mlo_link_disable_event
Extract the wmi event params and store in host defined
structure.
Change-Id: I6893bfa4da7b27f4a9b1ce2936057bb3576a317c
CRs-Fixed: 3458680
Currently the DebugFS logic in utils/fwlog/dbglog_host.c is protected
by the flag WLAN_OPEN_SOURCE. The WLAN_OPEN_SOURCE flag is a legacy
flag which had a specific use that is no longer valid. So replace the
use of WLAN_OPEN_SOURCE with a feature-specific flag.
Change-Id: I82c51efff8dfe6673c6b9d956f974cae2d21bb69
CRs-Fixed: 3464911
Extract htt_msdu_idx_to_qtype_map array from wmi service ready
ext2 event, it is needed for DP TX ILP feature enablement.
Change-Id: I64766f5b6ebc6632ce4994a8d53224d98beb5879
CRs-Fixed: 3445507
New TLVs for MLO link state information is introduced for
get link info command. Add WMI changes to add these TLV in
get link info command
Change-Id: Ib8d12a727ac6f59257dcce69174271330a065c77
CRs-Fixed: 3431076
Add support for WMI_CSA_IE_RECEIVED_EVENTID as:
1. Register the handler
2. Handler to extract the event
Change-Id: I9f476c7fbc51d9686d05fbdb5f46dec3bcd3c29e
CRs-Fixed: 3431363
Added change,
1. Define new DBR module DBR_MODULE_CBF to handle TxBF
standalone sounding CV data and corresponding ring
initialization.
2. API to extract new meta data TLV added for CV data.
3. API to handle standalone sounding complete.
Change-Id: Id28c5561bb8b3bf08de7ddd9aa2365e2ae99f1c2
CRs-Fixed: 3415627
1. Make changes to selectively send the Link control WMI to the
FW with out including the T2LM TLV.
2. Modify the TLV definitions for Link preference to use the newer
Link control TLV.
Change-Id: Id8beae8376ee5d2fb3434367530a0a6bb976597d
CRs-Fixed: 3422692
Add API extract_tgtr2p_table_event_tlv to extract TLVs from the response
event of rate2power table update cmd. Add a wrapper function
wmi_extract_tgtr2p_table_event and call extract_tgtr2p_table_event_tlv
from it.
Add the host event id wmi_pdev_set_tgtr2p_table_eventid corresponding to
the target id WMI_PDEV_SET_TGTR2P_TABLE_EVENTID. Also add this mapping
to populate_tlv_events_id function.
Change-Id: I0a870125120f1f92ee50002953e114b27d597ae6
CRs-Fixed: 3405417
Add the function pointer 'send_set_sta_max_pwr_table_cmd'. The
corresponding function sets max tx power limit for each sta
The function pointer mentioned above calls the
send_set_sta_max_pwr_table_cmd_tlv API to fill the each STA max power
values in appropriate WMI structure and sends to the FW.
Change-Id: I62cba94645e942fb63415d81cd9c2a1f5be3f47e
CRs-Fixed: 3399241
Currently, firmware sends WMI_WLAN_FREQ_AVOID_EVENTID with set
of frequency ranges to be avoided when it finds LTE operating
around those frequencies. Host driver marks these frequencies
as unsafe and doesn't operate in SAP/P2P-GO mode.
There is a new requirement where SAP can be allowed to operate
in unsafe channels when below conditions are met,
1. Firmware advertises the capability fix_channel_priority in
WMI_COEX_FIX_CHANNEL_CAPABILITIES through ext2 event.
2. SAP is started in a fixed channel.
Fetch the capability fix_channel_priority sent by firmware and
cache it in wlan_psoc_host_service_ext2_param to support
this feature. Add APIs to cache value received from firmware in
psoc_info->info.service_ext2_param.sap_coex_fixed_chan_support
and to fetch the same.
Change-Id: I8ceb501240bc86d6b004446f9927f4402c487203
CRs-Fixed: 3381399
The kernel-doc script identified many documentation issues in
the wmi folder, so fix them.
Note that in quite a few cases there is duplicate documentation in .h
and .c files, and in those cases remove the documentation from the .c
files since the interface should be documented, not the
implementation.
Change-Id: I097d5b8e8f0ba09046b7b8abe338d05a00f8cc7e
CRs-Fixed: 3372831
Realloc memory for wmi_service_ext_bitmap when
WMI_SERVICE_AVAILABLE_EVENTID event come, and
the num of wmi_service_ext_bitmap large then
previous num.
Change-Id: I2800fe3274e5516369486ef065ce03ba121bd5b3
CRs-Fixed: 3346739
Add ucfg and wmi changes to support for green ap low latency
power mode enable/disable command.
Change-Id: Ib9112e384c8354f1eff0f15610301225d51ef3ac
CRs-Fixed: 3265649
This change is to allow other modules to register for
link disablement.
It includes below functions:
1- Notify link update
2- Register to handler to get link update notification
3- Unregister T2LM handlers
Added the below changes as well,
- Move T2LM related data structures to wlan_mlo_t2lm.h file
- Host receives the expected duration from FW for multiple vdevs.
Hence, add support to extract the expected duration for multiple vdevs.
Change-Id: Ie8e77d5d3b4351a8551ecd7da50786b58dad3b2e
CRs-Fixed: 3346432
Add WMI interface(WMI_VDEV_SET_TWT_EDCA_PARAMS_CMDID) to
configure EDCA/PIFS param for LL SAP.
This configuration depends on edca_param_type.
If edca_param_type is 0 then host will configure EDCA param and
send it to firmware via WMI interface.
If edca_param_type is 0 then host will configure PIFS param and
send it to firmware via WMI interface.
Change-Id: I4f2e4120a258cc4a20aabeed503709aa2ceb8ec9
CRs-Fixed: 3349467
To assist the Host in ML reconfiguration element construction for probe
responses, FW sends MLO link removal information as part of the MGMT Rx
event containing the corresponding probe request. This information is an
array of TLVs, one TLV for each link that is undergoing link removal from
the MLD for which this probe request is intended. The TLV carries the link
removal TBTT countdown value maintained by the FW for that link.
Add support to extract the same.
CRs-Fixed: 3335361
Change-Id: I16c6791a443ddb166da596d404a52ff2a38da291
WMI_MLO_LINK_REMOVAL_EVENTID will be sent by FW to update the Host with the
progress of the link delete operation. Add support to extract the TBTT
update TLV sent in this event.
Change-Id: I01ce710d282f16e7a7cf4fb767279661558d129f
CRs-Fixed: 3322714
WMI_MLO_LINK_REMOVAL_EVENTID will be sent by FW to update the Host with the
progress of the link delete operation. Add support to extract the fixed
params TLV sent in this event.
Change-Id: Ic42a822339363b1347ae174926a4dac19eef3f99
CRs-Fixed: 3318005
WMI_MLO_LINK_REMOVAL_CMDID is to be sent by the Host to initiate the
removal procedure for a given link from its MLD. This command will be sent
on the impacted link only. Add support to populate and send this command.
Change-Id: I8485d8c8897bb2bb891d50546d5fbfac2a69a4ce
CRs-Fixed: 3314430
Add API to parse the TID-to-link mapping event ID for the AP vaps.
As part of this event,
- Update the mapping switch time TSF value in host data structures.
- When mapping switch time or expected duration expires in the FW,
update the host data structure.
Change-Id: I93232429fe5c2aa12dc4bf9f6a2f014761b7df15
CRs-Fixed: 3350697
Add support for vdev level WMI Command and event to send
and receive t2lm ie info
CRs-Fixed: 3339695
Change-Id: I8b896a961cba8f1d8e11111f900a98da090b9513
Add changes to indicate ongoing critical update CU flags and
BPCC values in probe and assoc/reassoc response.
For beacon FW update the CU flags and BPCC values in impacted
and partner links and keeps the latest copy of BPCC for ML VDEV.
The similar CU indication needs to be considered for probe,
assoc/reassoc response.
FW indicate to host the ongoing CU flag within DTIM interval for
impacted, and latest BPCC values of AP MLDs in impacted
and partner link VDEVs as part of mgmt_rx_event.
Extract cu_vdev_bitmap and bpcc values CU information from
wmi_prb_tmpl_ml_info TLV for probe and assoc / reassoc request.
Pass these values to umac, mgmt and ol layer as part of rx status.
Refer these values to update CU flag in capability information,
and BPCC values to update BSS Parameter Change Count in RNR,
MLIE and per sta profile.
CRs-Fixed: 3301916
Change-Id: I92ededb6598f85f3ea21b9d5e69d182c6180e30d
