Some panels may require that the DSI link returns to the low-power
stop state (LP11) after transmission of every line. If a panel
requires that the DSI link returns to LP11, apply the LP11
insertion between lines feature.
This change adds support to
- Disable the command mdp burst mode
- Enable mdp idle ctrl
- Program the No. of dsi pclk cycles of idle time to
insert between command mode mdp packets. The idle time
must be long enough to cover the time link takes to
switch between HS to LP11 mode.
Change-Id: Ie718d334f05ce6c1ecd1a05b379bbbe18dec6330
Signed-off-by: Ritesh Kumar <riteshk@codeaurora.org>
Creating a generic api that can be used with the driver
for read poll timeouts. This allows for easy overriding
of the function, if necessary.
Change-Id: I7bc5176ebabe782089b1a4d6e94c17ad3eb9ada4
Signed-off-by: Nilaan Gunabalachandran <ngunabal@codeaurora.org>
Signed-off-by: Michael Ru <mru@codeaurora.org>
Removes files and version checks for unsupported DSI Controller
HW versions.
Change-Id: Ic0acd34959ddfcf2db79102857e15f4e06da1d3a
Signed-off-by: Michael Ru <mru@codeaurora.org>
When Broadcast is enabled, DMA_DONE bit gets set for slave
controller on command transfer completion but it is not
getting cleared. Due to this, DMA transfer failures on slave
controller are not getting caught. This patch add supports for
clearing DMA_DONE for slave controller on every successful
transfer. This also prints error if transfer fails on slave
controller.
Change-Id: I61ce7b2d8be323adc70d888b5a2416afd9ae9fac
Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
Change adds support for enabling splitlink sublinks video data swap.
Change-Id: I731b85a5e8fe8638005433819957dd0658f72963
Signed-off-by: Vara Reddy <varar@codeaurora.org>
Fix dlkm compilation errors that are due to the use of -Werror
flags used by the build system.
Change-Id: I5e1e9bc63c1361d73e4930aab123212717872ecb
Signed-off-by: Tatenda Chipeperekwa <tatendac@codeaurora.org>
when a broadcast DSI command is scheduled, the command can get
triggered close to the schedule line. This might cause DMA
timeout. This change reads the video line count from
MDP_INTF_LINE_COUNT register and checks whether DMA trigger
happens close to the schedule line. If it is not close to the
schedule line, then DMA command transfer is triggered.
Change-Id: Ida92e63e46b4cc703d57ce24097834f810776aa8
Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
During ESD check failure, DSI video engine can get stuck
sending data from display engine. In use cases where GDSC
toggle does not happen like DP MST connected or secure video
playback, display does not recover back after ESD failure.
This change adds support to perform soft reset when DSI
video engine gets stuck.
Change-Id: I9cb31e6c71c4da171f9fe22fc3bee9175711831d
Signed-off-by: Ritesh Kumar <riteshk@codeaurora.org>
As per DSI HPG, Soft reset is not required to disable
video mode operation for version 1.3.0 and later. So,
add check to skip it during display disable.
Change-Id: If6d263bdf22f8a6fbef76d78d04bb9d11be05945
Signed-off-by: Ritesh Kumar <riteshk@codeaurora.org>
Signed-off-by: Steve Cohen <cohens@codeaurora.org>
Add support to read cphy boolean flag from panel dtsi
and configure DSI PHY registers accordingly. Update the
bit/byte clock calculation according to cphy specifications.
Update clock parents so that the relevant divider blocks
are configured to support cphy.
Change-Id: Iaca61eec01a488657b086f59910c52f8c79e26a4
Signed-off-by: Chandan Uddaraju <chandanu@codeaurora.org>
Signed-off-by: Yuan Zhao <yzhao@codeaurora.org>
From Lahaina onwards, for compressed DSI output, widebus should be enabled.
In widebus mode, 6 bytes of data are transmitted per pclk.
For uncompressed output, widebus must be disabled to transmit 3 bytes
of uncompressed data per pclk.
Change-Id: I7fc0bdb2e1678152d57b4cbb8295063a2ba8ae73
Signed-off-by: Rajkumar Subbiah <rsubbia@codeaurora.org>
Move DSI debugbus dumping logic from DSI driver to sde_dbg
in order to utilize the framework in place for debugbuses.
This allows for more control over the dumping logic, such
as where the dump data is stored(memory/console), via nodes
populated in debugfs.
Change-Id: Iff507fdaa02d26af26743e81f6048aec57c09a76
Signed-off-by: Steve Cohen <cohens@codeaurora.org>
Add the support to program DSI compression registers
for VDC-m. These are calculated based on the VDC parameters
and mode information.
Change-Id: I09b163a496842331d5f2a78371f380180b3a15b8
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
This change enforces dp, dsi and the sde drivers to use the
drm framework defined dsc_config data structure. As a part of this,
it introduces the sde_dsc_helper API to configure the dsc params
and creating a PPS command. Earlier each driver implemented it's
private versions leading to duplication of code. Additionaly the
helper api supports DSC spec 1.2 422 and 420 mode.
Change-Id: I25933fab08cdabbc6787079926885d1a78945e97
Signed-off-by: Abhijit Kulkarni <kabhijit@codeaurora.org>
Change lowers the log level of the debug bus dump to info.
Change-Id: I129f9f2e611428dc392d7888df43870beddac307
Signed-off-by: Vara Reddy <varar@codeaurora.org>
Adding debug, info and error prefix for log messages
in dsi files. To enable debug logs
run "echo 0x1 > /sys/module/drm/parameters/debug"
Change-Id: I438ac16954bd1d39450f8adeb7fb17f9ea6f8140
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
This change is a snapshot of dsi files taken of 4.14
as of commit 764f7c2 (Merge remote-tracking branch
'quic/dev/msm-4.14-display' into msm-4.14)
Change-Id: I8361a844c35a4450f7800964a8da2741676fd6c7
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
This change adds support for dynamic switching of dsi clocks
to avoid RF interference issues. Also with dynamic dsi clock
switch feature coming into picture, now populate the supported
refresh rate as list instead of providing a range. Modify the
logic to enumerate all the modes in dsi driver, taking dynamic
bit clocks, resolutions and refresh rates into account.
Change-Id: I5b6e62bc935cf2234bdd96fcb3c7537b4e735fff
Signed-off-by: Sandeep Panda <spanda@codeaurora.org>
Signed-off-by: Ritesh Kumar <riteshk@codeaurora.org>
Signed-off-by: Yujun Zhang <yujunzhang@codeaurora.org>
This change brings msm display driver including sde,
dp, dsi, rotator, dsi pll and dp pll from base 4.19 kernel
project. It is first source code snapshot from base kernel project.
Change-Id: Iec864c064ce5ea04e170f24414c728684002f284
Signed-off-by: Narendra Muppalla <NarendraM@codeaurora.org>
