Creating a generic api that can be used with the driver
for read poll timeouts. This allows for easy overriding
of the function, if necessary.
Change-Id: I7bc5176ebabe782089b1a4d6e94c17ad3eb9ada4
Signed-off-by: Nilaan Gunabalachandran <ngunabal@codeaurora.org>
Signed-off-by: Michael Ru <mru@codeaurora.org>
Cleanup DSI HW register access layer to minimize the number of macros that
access readl/writel functions.
Change-Id: Id78025b3837f9126f64681b4c1c1e13aec762081
Signed-off-by: Michael Ru <mru@codeaurora.org>
Change adds support for transferring commands to each sublink.
Change-Id: Iefc0dca7343325cdfe0cf48d41d50e6e2a13bc05
Signed-off-by: Vara Reddy <varar@codeaurora.org>
As per the HW requirements it is highly recommended to use DMA start
window to trigger broadcast commands. If not used then it can
result in a hardware hang with the DSI controllers going out
of sync. This behavior is even more prominent in cases of higher
refresh rates. As part of the change we change the default DMA
scheduling behavior to default to maximum possible DMA window
in case it is not specified in the panel device tree.
Change-Id: Ied4df9063664cedbc18ce009054d4e5ecae30ab2
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Currently, mdp_intf_line_count and mdp_intf_tear_line_count register
addresses are defined in dsi_ctrl_hw for debug feature. But mdp_intf
base address is target specific and independent of dsi controller
version. This change adds support for parsing the mdp intf base
address from dt, thereby remapping using base + offset addressing.
Change-Id: Ibb72dfe84a786a5c8b95f6a400e8333f6b46814a
Signed-off-by: Lipsa Rout <lrout@codeaurora.org>
The change adds register mapping of MDP_INTF_[1/2]_TEAR_INT_COUNT_VAL
register to DSI controller. This allows for the controller to read the
line count and frame count of the read pointer during trigger and
successful transfer of DMA command.
To enable the debug feature:
echo 1 > /d/<panel_name>/dsi-ctrl-0/enable_cmd_dma_stats.
To disable the debug feature
echo 0 > /d/<panel_name>/dsi-ctrl-0/enable_cmd_dma_stats.
To read line count value:
cat /d/<panel_name>/dsi-ctrl-0/cmd_dma_stats.
Change-Id: I5cdeb54ca941af05b226a9d7ab332b899ecc5797
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
The change allows for configuring a command DMA window during which
the command is triggered. The DMA window must not intersect with the
MDP tear check window. Once the command transfer is successful, the
trigger control needs to reset to the default DMA trigger specified
by the panel.
Change-Id: I5485ca1f8e141ed92dc8c77c2daf579634271022
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Avoid sharing and have dedicated dsi HW ctrl ops across versions
even if they are identical. It helps to stub out a specific
version of ops if needed.
Change-Id: Ic14c206b526ebe03dd5f47f62701820e7e542670
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Adding debug, info and error prefix for log messages
in dsi files. To enable debug logs
run "echo 0x1 > /sys/module/drm/parameters/debug"
Change-Id: I438ac16954bd1d39450f8adeb7fb17f9ea6f8140
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Continuous splash enabled displays are identified by reading
the MDP ctl registers. DSI cont-splash init settings are
called based on this. Additionally, DSI reads the DSI-CTL
scratch register set by bootloader to detect cont-splash.
This change removes the redundant mechanism in DSI to
detect cont-splash.
Change-Id: Ic58be1e62eda239fcea5e82d9d356905dc552a73
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
This change brings msm display driver including sde,
dp, dsi, rotator, dsi pll and dp pll from base 4.19 kernel
project. It is first source code snapshot from base kernel project.
Change-Id: Iec864c064ce5ea04e170f24414c728684002f284
Signed-off-by: Narendra Muppalla <NarendraM@codeaurora.org>
