DCE_DATA_COMPRESS BIT needs to be set to 0 before
the non-dsc frame is triggered in dsc to non-dsc switch
case.
Change-Id: I311dd3f0274d7c6b0baf2328cc50b584e4560915
Signed-off-by: Raviteja Tamatam <travitej@codeaurora.org>
While programming intf block Mux configuration with
binding ping pong, avoid clearing split select field
as clearing this field would enable split by default.
Change-Id: Iad2fa81969bc59abba4467f29661e62c63ba19c0
Signed-off-by: Prabhanjan Kandula <pkandula@codeaurora.org>
Add AVR step support so SW can trigger a late frame and instead
of immediately triggering, HW will perform the update at the
start of the next step interval. This allows for a fixed SW
vsync timeline to be maintained in userland, eliminating the
usual drift from the actual HW vsync caused by a late frame.
This change adds AVR_STEP support via a DRM property.
Change-Id: I4cf8a296989805f134c2165a3bed0b050bb09c96
Signed-off-by: Steve Cohen <cohens@codeaurora.org>
Report the AVR_STATUS which indicates if there's a pending
trigger when Adaptive Variable Refresh feature is enabled.
This allows SW to detect whether the old frame is repeated
or if the new frame was taken when the trigger is very
close to Vsync.
Change-Id: I6b04482e5c4c3bb92bad426c529c1fd3612d41c3
Signed-off-by: Steve Cohen <cohens@codeaurora.org>
Change adds support for splitlink and disables
dsc merge or 3dmerge which is not needed for splitlink.
Change-Id: I77a794d3ea6f53988f493a7af792add81abb22f0
Signed-off-by: Vara Reddy <varar@codeaurora.org>
From MDSS 8.x, vsync timestamp counter register is added in all the
interfaces. Add interface to get the vsync counter and use the global
qtmr reference counter to get the counter delta. This can be used
with reference to the curret ktime to deduce the accurate vsync
timestamp. This utility is intended to be used for setting the vblank
and retire fence timestamps which would be notified to user-mode.
Change-Id: I608a284c035cda50053eedbb311f1f54b3d3d557
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
From MDSS 8.x INTF line/frame counters can be reset through
a register. Reset these counters during timing engine enable /
tear-check enable to keep track of meaningful counters, which
would be useful during debugging. Additionally, reset the
counters during cont-splash modeset to track the number of
auto-refresh frames while disabling it during the first frame.
Change-Id: I66b45f5b29793df1fb4635972b1c614ad8c3b5b3
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
Watchdog timer is moving from TOP to INTF. This change adds
support for movement and ensures backwards compatibility.
Vsync select only needs to specify whether or not to use
Timer 0 associated with the interface. It does not need to
select between Timer 0-4.
Signed-off-by: Samantha Tran <samtran@codeaurora.org>
Change-Id: I9d89a8cb1ea607e9fc0bdbffa0a6a9acceff7f13
This change replaces kzfree with kfree as kzfree has been
renamed.
While moving to the latest 5.10 tip, additional small changes
were required to resolve compilation issues:
set_dma_ops has moved from dma-mapping to dma-map-ops header.
This change includes the new header file required.
drm_panel_add returns void, this change removes the expected
return value check.
drm_prime_pages_to_sg takes an additional parameter. This change
passes in the drm_device pointer the function is looking for.
Remove an unused variable in sde_crtc vblank function.
Change-Id: I47c085c0cb64432873c2e750ae64cbdc2b5340da
Signed-off-by: Samantha Tran <samtran@codeaurora.org>
A new status register was added in DPU 5.x to INTFs to allow for
confirmation when the timing engine is disabled. This
functionality was controlled via an overloaded feature flag
which is used to enable INTF tear-check ops (also added in DPU
5.x). External displays support INTF_STATUS but have no use for
any tear-check functions. Separate these features so they can be
enabled individually on the interfaces which support them.
Change-Id: Ib8548619cb58bf19b7c02211ead7f33f52ffeae4
Signed-off-by: Steve Cohen <cohens@codeaurora.org>
Add the INTF interrupt status register value to the underrun
line count event log to assist in debugging these issues.
Change-Id: I847cb12f8b4565d5f04667e0abda5d051a6194b2
Signed-off-by: Steve Cohen <cohens@codeaurora.org>
From Lahaina onwards, widebus is enabled for compressed DSI stream.
This change adjusts interface timing parameters to account for widebus.
Change-Id: Ie6b739ed2cdb515064e3a94404b3e0fe07755d7e
Signed-off-by: Rajkumar Subbiah <rsubbia@codeaurora.org>
Update autorefresh disable sequence-2 by avoiding
tearcheck enable configuration. Updated sequence
will trigger the frame by resetting the write
line count with tearcheck start position.
Change-Id: I984251c0cb23475f20cd5ea62122a167324d6670
Signed-off-by: Dhaval Patel <pdhaval@codeaurora.org>
Autorefresh might be still in enabled state after
write_ptr reached to display height. This patch
checks the autorefresh status bit and keeps polling
the bit till autorefresh sequence is in enabled
state. It times out after 1 second if autorefresh
is still in enabled state.
Change-Id: I5d4f4cb35e5cc8c680c1878f52cee385f709d764
Signed-off-by: Dhaval Patel <pdhaval@codeaurora.org>
This change adds logic to align timing engine vsync with panel
tear check if it is supported.
Change-Id: I3f881f392929589848c893f567822b21c0650000
Signed-off-by: Narendra Muppalla <NarendraM@codeaurora.org>
Add underrun line count information for each underrun.
Change-Id: I34a740c33240fa8d444f4bbc3b8b014b0282fca1
Signed-off-by: Dhaval Patel <pdhaval@codeaurora.org>
This change enables the interface hw block to accept
64-bit compressed pixels. This configuration is enabled based
on hw capability. For current hw, this is required any time
the compressed pixels flow through the interface block,
whereas in the previous version of DPU hw this configuration
is only required for topology using 4 way dsc merge.
Change-Id: I7bf79d035dba5084c5057022a7fa1117479e8d52
Signed-off-by: Abhijit Kulkarni <kabhijit@codeaurora.org>
Defines should always have a single space between #define and
the keyword to allow for searching where these definitions are
located using grep.
Change-Id: I38778e789b12df8a7a22c22dd27152a5ab047405
Signed-off-by: Steve Cohen <cohens@codeaurora.org>
Add support to enable one-shot mode during qsync
update. This feature ensures the frame drops can be
reduced due to delayed software flush for the
current commit. Also, add changes to disable the qsync
feature post commit.
Change-Id: Icb158853f52284bcf8fa641e5f62200c5460b660
Signed-off-by: Kalyan Thota <kalyant@codeaurora.org>
Signed-off-by: Jayaprakash <jmadiset@codeaurora.org>
Allow Qsync and VRR features to be supported independently
by display driver. Restrict the feature availability in
same composition cycle.
Change-Id: I696eb72a2b4f9451e142ffdc5acccc8987c36b6d
Signed-off-by: Kalyan Thota <kalyant@codeaurora.org>
Signed-off-by: Jayaprakash <jmadiset@codeaurora.org>
CWB, DP and WB displays tear down sequence must reset
3d_merge, ctl, pingpong_binding, etc. MDP HW
blocks. This change fixes the tear down
sequence register programming. It also moves flush
sw reset before encoder_disable call. That allows
CWB tear down to update the flush configuration
on primary ctl path.
Change-Id: I21c521b39456af4144cf836c65d46a25c985f51d
Signed-off-by: Dhaval Patel <pdhaval@codeaurora.org>
Log hardware interface framecount during te and vblank irqs for
command and video mode panels, respectively. This will help in
debugging any missed frames.
Change-Id: Ie86f686c4cc12de6a1f31aa47d4c7a5b8a68ea55
Signed-off-by: Nilaan Gunabalachandran <ngunabal@codeaurora.org>
This change ports the missing changes from 4.14 to 4.19
that were missed. It includes changes up until
commit 0f8fb25421ff ("cnss2: Add device version to
SOC info structure").
Change-Id: Idfdfe891f146e389e3c65cc3fc4c98d93220e789
Signed-off-by: Samantha Tran <samtran@codeaurora.org>
SDE driver triggers the frame and waits for the
ctl_start interrupt for command mode display. This interrupt
provides confirmation that hardware has picked up the
frame. Retire fence signaling is associated with
this interrupt and it is sent at the rd_ptr interrupt
after ctl_start. Due to lut dma delay, ctl_start interrupt
may be trigger before rd_ptr or after rd_ptr. SW manages
this complexity and handle retire fence for different cases
with 500us threshold logic.
This change replaces the ctl_start interrupt with wr_ptr
interrupt by programming it to trigger at 1st write line
count. This is guaranteed to come every time and it is close
to rd_ptr interrupt. That allows retire fence trigger at
wr_ptr interrupt and simplifies the SW logic. CRTC commit
thread would be held slightly longer with this change
as the wr_ptr is always close to rd_ptr and after
ctl_start.
Change-Id: Ic47a8f82c854b4aded0d70c95af853b28a68ffd6
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
This change brings msm display driver including sde,
dp, dsi, rotator, dsi pll and dp pll from base 4.19 kernel
project. It is first source code snapshot from base kernel project.
Change-Id: Iec864c064ce5ea04e170f24414c728684002f284
Signed-off-by: Narendra Muppalla <NarendraM@codeaurora.org>
