Add support for AFC specific Host service flags to switch
between LPI only and SP+LPI, disable AFC timer and request ID checks
in target.
Change-Id: I34d6adcad6e4a2cd6383c941ed07b98059daeed0
Add support for extracting Thermal Stats Events
from thermal event TLV for FW event
WMI_THERM_THROT_STATS_EVENTID.
Also, added support for FW Cmd to request for
Thermal Stats: WMI_REQUEST_THERMAL_STATS_CMDID
Change-Id: I2bc80d082bda45e2255371bcb0c31d35d9806525
CRs-Fixed: 3016845
When MGMT frames are consumed by the FW, FW sends MGMT Rx FW consumed event
to the Host. Add WMI layer functionality for this event handling.
Change-Id: Id95f41a717b88589e861781e1111b17dc90475be
CRs-Fixed: 2959118
With latest architecture there are different HTT peer
data versions supported by the firmware, supported htt peer
version will be sent in the service ready and need to feedback
to the firmware in the init command.
Change-Id: Icd0470843198387cd7e0192cbe3821d45ef0534e
CRs-Fixed: 3008706
Add new field ema_init_config to signal the configured value of
beacon size while using MBSSID feature in 6Ghz.
The current allowed range is 1500-3500 bytes.
CRs-fixed: 3004041
Change-Id: Id8cc1b7e4602b2e52b8eb215337070c6e3c26089
Add P2P_P2P_CONCURRENCY_SUPPORT service capablity to
validate whether fw can support p2p concurrency
support or not. when firmware advertises this flag it
can support MCC,SCC, DBS for p2p-GO/GC + p2p-GO/GC.
Change-Id: Ifec4bf984595b06374be9024601733c8537a9c3e
CRs-Fixed: 2984165
A new TLV is added to send partner link CSA/ECSA count offset to FW as
part of beacon template. Add WMI changes to populate these TLVs in the
beacon template send function.
To fix the compilation issue, added forward declaration of 'struct
vdev_mlme_obj' and removed 'include/wlan_vdev_mlme.h' include file from
wlan_mlo_mgr_public_structs.h.
Change-Id: I6e421b29bb887bec711a23db1458aca4d112ade4
CRs-Fixed: 2983249
In WMI INIT, check whether firmware supports the ack event or
not. If it supports then enable driver support and send it to
firmware during WMI INIT.
Change-Id: Icfdee6bc06e6a393de880b87fdab70665ea7c8b4
CRs-Fixed: 2987898
In case if TWT command (i.e setup, terminate, pause, resume,
nudge) comes from userspace and if the firmware is in below mode
1. scan in progress
2. roam in progress
3. CSA is in progress or
4. Any other error
then the command needs to be rejected in userspace context.
Synchronize the TWT command so that whenever command goes from
driver to firmware, then driver will receive ack event first
followed by respective event (i.e add dialog, delete dialog,
pause, resume, nudge) with below condition
1. If driver receives the ack event as successful then driver
waits for this ack event, respective event with status of the
TWT action frame over the air is expected.
2. If driver receives the ack event as failure then it will
rejects the TWT command in userspace context.
Change-Id: Ie885d98ecf2dad98d34676d889fd70e4c84f0a05
CRs-Fixed: 2987904
Changes to extract AoA phase delta values from WMI event.
The AoA phase delta values along with ibf calibration value
is shared to derive the phase values which is to be used in
CFR.
Change-Id: I70f50656db4194025a0b6b37c8b4a27048968e0f
Check the below service bits and set in psoc if the service is supported
by FW.
WMI_SERVICE_RTT_AP_INITIATOR_STAGGERED_MODE_SUPPORTED
WMI_SERVICE_RTT_AP_INITIATOR_BURSTED_MODE_SUPPORTED
Change-Id: I13504958bf31b2d645d915b4db20719bdc9a4133
CRs-Fixed: 2969195
Add WMI support for EHT puncturing by filling puncture
bitmap in vdev start and peer assoc commands.
Change-Id: If1d2541655558f22a96a741999ec4ff7348f695a
CRs-Fixed: 2982498
First Requirement:
In case of WTC_BTM roam trigger reason, if FW reports rssi
threshold for 5G and 6G AP via wmi_roam_trigger_reason,
Host should print it in kmsg.
If wtc_candi_rssi_ext_present is set (1), It means fw
reports 5g and 6g candidate rssi (new firmware case).
If wtc_candi_rssi_ext_present is clear (0), It means fw
doesn’t report 5g and 6g candidate rssi (old firmware case).
Host use flag "wtc_candi_rssi_ext_present" to keep backward
compatibility.
Second requirement:
As per user space, value for scan mode in WTC command, is
like below:
0: no Scan, 1: partial scan and 2: full scan.
For NO scan case, FW sends value
ROAM_TRIGGER_SCAN_MODE_NO_SCAN_DISCONNECTION (3)
in wmi_roam_trigger_reason-> wtc_scan_mode. When driver receives
WTC scan mode as ROAM_TRIGGER_SCAN_MODE_NO_SCAN_DISCONNECTION,
it should print value as 0 instead of 3.
Convert WTC scan mode comes from FW to
wmi_configure_roam_trigger_parameters->scan_mode to make it
compatible to WTC command.
Change-Id: I8266460aac1272d345e4349c2ca52b4f9a745d4c
CRs-Fixed: 2965362
Add functions to parse and extract wmi smart monitor
event received from target.
Change-Id: Ic18e3134b684c5f8e12839e997d628909a7e27c9
CRs-Fixed: 2969247
Currently the 6G edge channel feature is MCC specific.
Make the 6G edge channel feature common for WIN and MCC.
Change-Id: I723b6db1d74dca5a911eede4ec6e6167f6b3e6bc
CRs-Fixed: 2976871
New TLVs for MLO flags are introduced in peer assoc WMI
command. Add WMI changes to add these TLV in the peer assoc
command.
Change-Id: I366a96c973c3bedda03e4c370099ff809e0bd83d
CRs-Fixed: 2958851
New TLVs for MLO flags are introduced in peer create WMI
command. Add WMI changes to add these TLV in the peer create
command.
Change-Id: I38a129b30b366b6e3939231699f210d1bac362a1
CRs-Fixed: 2958849
Add parameter 'bool sync' for wlan_cfg80211_crypto_add_key()
to indicate whether or not to add key synchronously.
If it's set to true, wait until install key complete event
is received.
Change-Id: I9a69d486665fb3f65a5720ccfbfb638c09329418
CRs-Fixed: 2865832
802.11BE D1.0 9.4.2.295c.4 Supported EHT-MCS And NSS Set
field specifies maximum 4 optional EHT MCS map, which are
20 MHz-Only STA, BW <= 80 MHz except 20 MHz-Only STA,
BW = 160MHz and BW = 320 MHz.
Therefore set WMI_HOST_MAX_EHT_RATE_SET to 4.
Also add a debug message to log peer_flags_ext.
Change-Id: I3d56998bf0de381ef147d6c0551dcdb7fd935f60
CRs-Fixed: 2963536
Set the SAE EAPOL offload support in resource config based on
WMI_SERVICE_SAE_EAPOL_OFFLOAD_SUPPORT bit received in service
bitmap from Firmware.
Change-Id: I878736105c070df514dfe8d989541227b3baad11
CRs-Fixed: 2957082
Fill peer assoc mlo params in peer assoc request command.
Also add definitions to the WMI_SERVICE_11BE.
Change-Id: Ied7959e022ee27f3bd698b84dc801491175f85b3
CRs-Fixed: 2934417
In WMI_HOST_TP_SCALE, add an option to support 6% transmit power scale
configuration.
Change-Id: I11a67f0efd13ba2c7f2d8d546643a1af37f33613
CRs-Fixed: 2936987
Extract the 11BE flags advertised by FW in WMI_SERVICE_READY_EXT2_EVENTID
and update the regulatory pdev wireless modes. The wireless mode is
currently represented as 'uint32_t' and all the 32 bits are exhausted.
To accommodate the new 11BE flags, change the data type of wireless_modes
from 'uint32_t' to 'uint64_t'.
Add a regulatory phymode 'REG_PHYMODE_11BE' in enum reg_phymode.
If the chip does not support 11BE phymode, FW advertises it via
WMI_REGULATORY_PHYBITMAP enum with a value of REGULATORY_PHYMODE_NO11BE.
Extract the phybitmap and store it in the regualtory
as 'REGULATORY_PHYMODE_NO11BE' bitmap.
CRs-Fixed: 2901260
Change-Id: I4ed3fc7c907b1f76e59efb347c747acea2a163b0
Updated the EHT related variables as per latest fw cmn headers.
Address review comments from previous EHT gerrits.
Change-Id: I67cd58a4efcf3e06d2ca3b5570432593b1d80825
CRs-Fixed: 2902607
Add 320Mhz band width support and EHT capabilities information in
WMI peer assoc command.
Change-Id: Ie4ee95fb1790c828275e90b384b2bdc04efb3f29
CRs-Fixed: 2882054
EHT capapilities will be received as part of ext2 service ready message.
Update the structure as per firmware common header file and extract the
EHT capabilities field.
Change-Id: Id2dd170db4de588008742f95493d4d06a6431f1c
CRs-Fixed: 2857802
Add support to read the WMI service bit describing support
for the DCS AWGN interference detection mechanism.
CRs-Fixed: 2906768
Change-Id: Id062b9d63a09f522ac1efdbaf6731665fa438630
Add support for storing AWGN interference information for
dynamic channel selection
CRs-Fixed: 2903860
Change-Id: I5d0b6cc0a55303cfb27a02b99aba066557ad9c7d
Enable lower 6G edge channel ch2 (5935MHz) for APL2 6G regdmn
using a service bit WMI_SERVICE_ENABLE_LOWER_6G_EDGE_CH_SUPP,
which is not enabled by default.
Also, disable upper 6G edge channel (7115MHz) using another
service bit WMI_SERVICE_DISABLE_UPPER_6G_EDGE_CH_SUPP, that
is enabled by default.
Change-Id: Ia7cb7f7d3165375178adbe70adb19b8671496b6d
CRs-Fixed: 2885623
In order to support different power levels of 6G AP and client,
the channel list event from FW namely "REG_CHAN_LIST_CC_EVENTID"
is modified to add few parameters specific to 6GHZ devices.
Hence the existing event is replaced by REG_CHAN_LIST_CC_EVENT_EXT for
all 2G/5G/6G pdevs in FW. Therefore, after the service ready event, FW
sends the channel list for the configured country/regdomain via
REG_CHAN_LIST_CC_EVENT_EXT. This mandates that all host software need
to have the processing capability of REG_CHAN_LIST_CC_EVENT_EXT to bring
up the AP.
As there can be host software which has not yet implemented the
version of "REG_CHAN_LIST_CC_EVENT_EXT", backward compatibility is lost
if "ONLY REG_CHAN_LIST_CC_EVENT_EXT" is sent by FW.
Hence a 3 way handshake between host and FW is established.
1. FW advertises its capability of processing REG_CHAN_LIST_CC_EVENT_EXT
id via wmi service bit 'wmi_service_reg_cc_ext_event_support'.
2. If the host is capable of processing the "REG_CHAN_LIST_CC_EVENT_EXT"
event id (which is done based on registration of this event), host
sends the capability in WMI_INIT_CMDID setting a bit in host_service_flags.
3. Based on host capability advertised in WMI_INIT_CMDID, FW decides to
send the old event ("REG_CHAN_LIST_CC_EVENTID") or the new event
("REG_CHAN_LIST_CC_EVENT_EXT").
4. If there is no flag indicated by host to FW in WMI_INIT_CMDID, FW
by default sends the old event ("REG_CHAN_LIST_CC_EVENTID").
CRs-Fixed: 2876360
Change-Id: Ibe95f414ad9fff0e5641bcc6e60450ef9afe245b
