updated sleep time to 80us from 20us after updating the
reset gpio pin from sleep to active state to give ample time
for HW to reset the pin state to active, to resolve the
component registration issue which is seen on stability
runs.
Change-Id: Icd13bf36d56906553352e595d07e478c23d1c13d
Signed-off-by: sarath varma ganapathiraju <quic_ganavarm@quicinc.com>
Defer the probe when the msm cdc pinctrl driver is not
proded.
Change-Id: Ia6aaaca7c55b60b53008ffda0fc40e5db407cd2a
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Add conditional check before calling wcd usb api
Change-Id: I9046ece531ea009e8b8cd5db98675960d928c1c6
Signed-off-by: Sarath Varma Ganapathiraju <quic_ganavarm@quicinc.com>
Change default OVP threshold to 4.2V, but set
to 4.0V during CODEC reset.
Change-Id: I4aa8accf7466e144902a2f6a250c1aad91084e95
Signed-off-by: Sam Rainey <quic_rainey@quicinc.com>
Update zdet and xtalk to support high voltage microphones
with improved accuracy.
Change-Id: I4b0af5ade7f653de4a938162302ec21c4a09891f
Signed-off-by: Sam Rainey <quic_rainey@quicinc.com>
When codec goes into suspend, disable vdd-px which
will cause an unvote in PM.
Change-Id: Ia9f958d67fc57dbf3932733797bce7b0eb742363
Signed-off-by: Eric Rosas <quic_erosas@quicinc.com>
For test program < 3, use local default trim values
for harmonium 2.0 version.
Change-Id: I8cdcbe83ddae4626cef1f3dc4bfab3b2c285a0ca
Signed-off-by: Phani Kumar Uppalapati <quic_phaniu@quicinc.com>
Update wcd939x register settings for 2.15V VDD_RX supply
and for 2Vpk and 1.4Vpk modes depending on the headphone
load impedance values.
Change-Id: Iae5e6087fe96d22c9b9f8b755c468d2e6dface4e
Signed-off-by: Phani Kumar Uppalapati <quic_phaniu@quicinc.com>
Add static variable to store version to avoid improper
device pointer in wcd939x_readable_register().
Update WCD939X_NUM_REGISTERS macro to be correct size.
Change-Id: Ib594f2f799ac2202ff78c02ccf2f6cdb80ffd38e
Signed-off-by: Eric Rosas <quic_erosas@quicinc.com>
Few register default values are incorrectly set for harmonium
codec in the register map table. Fix it by setting correct
values as per the hardware interface documentation.
Change-Id: Ibcb517d6050a4932243ead396e6f89294aab4a23
Signed-off-by: Phani Kumar Uppalapati <quic_phaniu@quicinc.com>
Check and update register sequences for wcd9395 version
2.0.
Change-Id: I85fc739744ee2ba2c5dbdc853eb639b84cac6478
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Add scale and alpha register value updates based
on computed digital xtalk cancellation gain.
Change-Id: I8c12e2ba7c1566476741fec5459a74549f19cf5f
Signed-off-by: Sam Rainey <quic_rainey@quicinc.com>
Update wcd939x-usbss mode on PA enable and disable.
Change-Id: I73a19ea73102ced5c8011a5a1567ebfa372b2e44
Signed-off-by: Eric Rosas <quic_erosas@quicinc.com>
Harmonium supports full and half rate modes for DAC.
Update DAC rate to swr clkdiv2 to achieve better
power performance.
Change-Id: I136a064dc258ee839ea78c9f1051ba34521ac871
Signed-off-by: Phani Kumar Uppalapati <quic_phaniu@quicinc.com>
Get the wcd939x power mode of from mixer ctls and configure
same power mode to wcd-usbss.
Change-Id: I9dc8fe586f7e7608da542b0986bb7c605fc552d4
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
For wcd939x LDORT_SCD_INT IQR register is removed, so remove
LDORT_SCD_INT register to avoid CMD ignore errors from RX SWR
while booting.
Change-Id: I6dfe6a1c32fddbcdbbf388b47efde60b6b4b5f35
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Disable legacy HPH surge protection
for certain platforms. Enable HPH over-current
protection for all platforms.
Change-Id: I147321417ad2152530a71b3990a7cbf064c9299f
Signed-off-by: Sam Rainey <quic_rainey@quicinc.com>
Add support for HPH 2Vpk output mode in the
WCD939X driver.
Change-Id: I44a84cde84f0feee6d7d1255e097a5ffb616f78e
Signed-off-by: Sam Rainey <quic_rainey@quicinc.com>
update HPH power mode comparison with mixer ctls enum names,
so this will pick the correct compander coeff values depends on modes.
Change-Id: I42cdfeceda4c4bac960b71bbd62d0e8528680490
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
For PCM mode no need to enbale PDM interrupts, so add condition
to skip for register of PDM interrupts. Also avoid unwanted register
writes for PCM mode.
Change-Id: I4675a7ffe94d1f8628a4f539829f5aa83544cf8d
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
update register based on latest version and add conditional
check to enable PCM path.
Change-Id: Ib2fe0b477adfa07bef52954993fbd6aae011500a
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
update registers based on specific hph mode before compander
config.
Change-Id: Iea4f2bc5521dc701bd52ce8fe24323b1f9d96045
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
add support for compander to enable and disable for HPHL and HPHR
in wcd939x.
Change-Id: Ib7aa96bd9faac7389b38f01baff0a93c646f84f2
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
On wcd939x contains only one variant. Sometimes reading
for codec variant which is giving incorrect/unsupported,
due to this incorrect mixer ctl are picked. So Wcd939x
is updated with supported variant WCD9395.
Change-Id: Ie556350b3630b6f1f76a4b2af1db795f908f13d4
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Use BIAS_LEVEL_OFF trigger from ASoC to mark the wcd/wsa power
supplies to LPM (if supported).
Change-Id: I89f232f9338168b99ae03f84318c21734b592f82
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
add mux in b/w IN1/2 and RX1/2 for configuring xtalk and
compander in hph pcm sequence.
Change-Id: I5ee97017585d03e0ef83841bbccef5982d79b9d9
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Update wcd939x api and marcro in pineapple driver
Update wcd939x macro in wcd939x driver.
Change-Id: Id87fc550e0a3aff61efee61644fd6bc15ea7c66d
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
