Extract htt_msdu_idx_to_qtype_map array from wmi service ready
ext2 event, it is needed for DP TX ILP feature enablement.
Change-Id: I64766f5b6ebc6632ce4994a8d53224d98beb5879
CRs-Fixed: 3445507
Add support for WMI_CSA_IE_RECEIVED_EVENTID as:
1. Register the handler
2. Handler to extract the event
Change-Id: I9f476c7fbc51d9686d05fbdb5f46dec3bcd3c29e
CRs-Fixed: 3431363
Currently, firmware sends WMI_WLAN_FREQ_AVOID_EVENTID with set
of frequency ranges to be avoided when it finds LTE operating
around those frequencies. Host driver marks these frequencies
as unsafe and doesn't operate in SAP/P2P-GO mode.
There is a new requirement where SAP can be allowed to operate
in unsafe channels when below conditions are met,
1. Firmware advertises the capability fix_channel_priority in
WMI_COEX_FIX_CHANNEL_CAPABILITIES through ext2 event.
2. SAP is started in a fixed channel.
Fetch the capability fix_channel_priority sent by firmware and
cache it in wlan_psoc_host_service_ext2_param to support
this feature. Add APIs to cache value received from firmware in
psoc_info->info.service_ext2_param.sap_coex_fixed_chan_support
and to fetch the same.
Change-Id: I8ceb501240bc86d6b004446f9927f4402c487203
CRs-Fixed: 3381399
The kernel-doc script identified many documentation issues in
the wmi folder, so fix them.
Note that in quite a few cases there is duplicate documentation in .h
and .c files, and in those cases remove the documentation from the .c
files since the interface should be documented, not the
implementation.
Change-Id: I097d5b8e8f0ba09046b7b8abe338d05a00f8cc7e
CRs-Fixed: 3372831
Add ucfg and wmi changes to support for green ap low latency
power mode enable/disable command.
Change-Id: Ib9112e384c8354f1eff0f15610301225d51ef3ac
CRs-Fixed: 3265649
Add WMI interface(WMI_VDEV_SET_TWT_EDCA_PARAMS_CMDID) to
configure EDCA/PIFS param for LL SAP.
This configuration depends on edca_param_type.
If edca_param_type is 0 then host will configure EDCA param and
send it to firmware via WMI interface.
If edca_param_type is 0 then host will configure PIFS param and
send it to firmware via WMI interface.
Change-Id: I4f2e4120a258cc4a20aabeed503709aa2ceb8ec9
CRs-Fixed: 3349467
In the current implementation, the Direct DMA completion event is getting
processed in the tasklet context. When the Direct DMA events land on the
same processor core as the one used by the WLAN data path events, the
Direct DMA events can pre-empt the data path events as the datapath
events usually run in NAPI context. This could impact the data path
throughput when there is a high volume of frequent Direct DMA events. To
fix this, Direct DMA events can be run in work queue context based on
user configuration. Add support for the same.
Change-Id: I1a89b185c6765addc7ee725e9324025f0318d9ed
CRs-Fixed: 3276157
On the initiator side, Host needs to send
WMI_VDEV_ADD_MAC_ADDR_TO_RX_FILTER_CMDID to firmware before sending the
PASN Auth frame. Hence, move send_set_mac_addr_rx_filter_cmd_tlv() from
wmi_unified_p2p_tlv.c to wmi_unified_tlv.c file.
Change-Id: Ia5517dbdd5ec46f611537b12b7046e3a9d859082
CRs-Fixed: 3304909
Adding feature flag for Health Monitor so that it can be disabled
for 16M and 256M profiles
CRs-Fixed: 3277434
Change-Id: Ibbbe582acd15ebff7e189fcbaa36429ea519db37
Currently host sends many vdev or pdev set param commands
separately to firmware.
Combine all vdev or pdev set params together where ever
possible, send to WMI.Based on service capability
WMI_SERVICE_COMBINED_SET_PARAM_SUPPORT, host decides whether
to send all set params to firmware at once to reduce number of
transactions or need to follow legacy way i.e send params
separately one after the other.
Change-Id: I0a36dd66a7ccb27f2ecd437cf7b9d08667e27472
CRs-Fixed: 3151418
Based on new requirement, driver needs to send feature set
information to fw as part of wmi init command.
With this change, fill the feature set info in feature set bitmap
and send this to fw with wmi init command.
Change-Id: Ic405c7e8e5ddd1399deacfaab240e979468c53c2
CRs-Fixed: 3262862
Add infra to support Dedicated Bluetooth Antenna Mode (DBAM)
feature. It is used to switch between dedicated antenna for
BT and shared antenna for WLAN and BT.
Change-Id: I21688093674ef9b63ee811df9168a31bd71c56b5
CRs-Fixed: 3239895
Rate-limiting will be based on number of beacons received.
When the beacon is not from connected AP, the beacons
are dropped on a percentage of received beacons and
rate limit, which is configured by the user.
CRs-Fixed: 3230508
Change-Id: Iac591c37129fda6923ef254c2950cb0bdbb44ce9
This enables the option to configure when a peer's
TID queue needs to be flushed. This is required to
discard packets that are no longer useful to the application.
Change-Id: I558debff043fc0c8038e5f5f2c815b64c90e1561
CRs-Fixed: 3130422
Add support in wmi to handle below new RTT PASN events:
WMI_RTT_PASN_PEER_DELETE_EVENTID
WMI_RTT_PASN_PEER_CREATE_REQ_EVENTID
Change-Id: Ib33c2def2d7ef66a6a2717e2a8e1756ab4318e4d
CRs-Fixed: 3150069
cal version is included in EXT2 svc ready message to indicate the bdf
and ftm version to host. Add API to extract this from ext2 message.
Change-Id: I83f4d6e83a3f78f993b40527aed7291c6496777c
CRs-Fixed: 3182634
Copy software image version, chip information,
pktlog json version and pdev id from the event received
from firmware.
Change-Id: I53c2fceee129fa69126ae8214fb652a744bfcbfa
CRs-Fixed: 3165004
Add WMI support to set PN Rx Filter which is used to forward
frames to host upon PN failure.
Change-Id: Ib32abc681e17e1a6189a295314a497fc0c21b15a
CRs-Fixed: 3150832
Extract information from wmi event wmi_vdev_quiet_offload_eventid and
send it to mlme
Change-Id: I49ef7f2811c5975a95e8e33050977c49e2b104e4
CRs-Fixed: 3101974
WMI_SPECTRAL_CAPABILITIES_EVENTID event will be sent by the FW to
indicate different capabilities of the Spectral HW.
Add support to extract the FFT size capabilities from this event.
Change-Id: I9640fa51e4249b9d1c2d9d3ac5da7f1d56c9d006
CRs-Fixed: 3098880
WMI_SPECTRAL_CAPABILITIES_EVENTID event will be sent by the FW to
indicate different capabilities of the Spectral HW.
Add support to extract the sscan bandwidth capabilities from this event.
Change-Id: I6ff6e5a8d80271fa62a430c986f53a321d46c66b
CRs-Fixed: 3098832
WMI_SPECTRAL_CAPABILITIES_EVENTID event will be sent by the FW to
indicated the different capabilities of the Spectral HW block.
Add support to extract the fixed parameters from this event.
Change-Id: Ib13108f078de008b6a76a25a010e85a7fdb6f5fe
CRs-Fixed: 3098203
Currently, VDEV manager responses are using legacy path instead of
target_if, vdev_mgr and os_if components. As the driver implementation
is planned for converged model, legacy implementation will be moved to
the respective components.
To avoid rework, Use target_if, vdev_mgr and os_if components to process
the FW responses corresponding to the vdev manager.
Change-Id: I778f6de93481fc730383e8f8e1c604f173947d69
CRs-Fixed: 3093776
As part of new enhancements, driver is supporting MAC address update
after VDE creation in the FW. To support this feature add WMI support
to send MAC address command to the FW.
Change-Id: Ie4b7291520793c8aa501fefccaf7b91ab22e9054
CRs-Fixed: 3084119
Add support to extract the freq, cfreq1, cfreq2, PHY mode, Destination
macaddr, and channel BW values from the RTT measurement request buffer
received from the LOWI application. Pass these values to a registered
callback. Users can use these values to make some decisions on the RTT
scan.
Change-Id: Idb2232c07bbfa2946dc01e75908b9a6036597ecf
CRs-Fixed: 3060685
Classify qmi/wmi by request type, only TYPE_STATION_STATS
is designed to be sent by qmi so far. other type will
continue go with wmi.
Change-Id: Ibaee99c0a9d59b0db634e84f3c0b6e40b65a185d
CRs-Fixed: 3077792
Waikiki facilitates a dedicated CE (CE14) for
direct DMA & diag handling purpose. Changes to
register the respective service handler to process
DBR and DIAG events from the target.
CRs-Fixed: 3057986
Change-Id: I4ae1d5676ac702d1f28f3e4031b47ffcd1d2ad7e
Add support for extracting SBS Lower Band
End freq from rx service ready event.
Change-Id: I402d7519507fbce733a000a546473aa00e8844d5
CRs-Fixed: 3065158
This change introduces the new roam set param WMI command to set
the roam params from host to FW.
Also added a fail_bssid param in wmi_roam_result TLV to know the
roam failed AP BSSID from the FW.
Added a new vendor command event for sending roam events stats
attributes to userspace.
Change-Id: I7a08635a7912cbd940d90a2d62433296740ad913
CRs-Fixed: 3050799
FW sends Spectral scan detector info TLV in WMI_PDEV_SSCAN_FW_PARAM
event to indicate the information of a detector participating in a sscan
session. FW sends one TLV of this type for each detector participating
in a spectral scan session. Add support to process the TLV and update
the spectral host data structures accordingly.
CRs-Fixed: 3044193
Change-Id: Ie17b6ea9336ada7a00e4594fa2f7f49ef3d443e5
