Use #if IS_ENABLED() instead of #ifdef for configurations as vendor module
guidelines.
Use #if IS_ENABLED(CONFIG_XXX) instead of #ifdef CONFIG_XXX to ensure that
the code inside the #if block continues to compile if the config changes
to a tristate config in the future.
The differences are as follows:
1.#if IS_ENABLED(CONFIG_XXX) evaluates to true when CONFIG_XXX is set to
module (=m) or built-in (=y).
2.#ifdef CONFIG_XXX evaluates to true when CONFIG_XXX is set to
built-in(=y) , but doesn't when CONFIG_XXX is set to module(=m).
Use this only when you're certain you want to do the same thing
when the config is set to module or is disabled.
Change-Id: Ia806b9b01ad8414d0e4de027a382cb68e7fb4a6a
Signed-off-by: GG Hou <quic_renjhou@quicinc.com>
Add support to parse and configure QoS values for offline writeback.
Expose a writeback connector property to allow user-mode to set
the usage type of the writeback block - WFD, CWB, offline-WB.
Change-Id: I864f79c4896ec757ac2d8b0f57a6a5775d164f21
Signed-off-by: Veera Sundaram Sankaran <quic_veeras@quicinc.com>
Add downscale blur connector properties to expose the hw block count,
downscaling filters used and the ratios supported. Add a custom dnsc_blur
property to allow usermode to send the required configuration to program
the hardware. Expose only for the virtual connector as the dnsc_blur is
only supported with writeback block.
Change-Id: I35dd263d9d5aafdb59bacbb3a0528ffd2bcaf6a3
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
This change adds support in mdp and dsi driver to support
multiple SIS.
Change-Id: I432068cea17e1784d7570a472fbadaa86695df07
Signed-off-by: Narendra Muppalla <NarendraM@codeaurora.org>
Signed-off-by: Amine Najahi <anajahi@codeaurora.org>
Commit d1d1173 ("disp: msm: update msm_gem ops and remove unused
drm_driver callbacks") Update msm_gem and msm_drv to comply with
latest 5.15 kernel.Modify dma_buf_vmap() and dma-buf's vmap callback
to use truct dma_buf_map. Rename dma_resv_get_excl_rcu to _unlocked.
Remove deprecated GEM and PRIME callbacks.
This change adapts all the interface change for kernel version 5.10
and version 5.15..
Change-Id: Icb495dc4e5d20999f773ed5881eff233ff3a48bc
Signed-off-by: Bruce Hoo <bingchua@codeaurora.org>
Add a cache_flag in msm_fb object to store the system cache state hints.
Writeback connector will store cache write hints if system cache write
is enabled while HW is writing into this buffer. Plane in the primary
display path, in a 2-pass composition strategy will use this cache hints
to enable the display HW to use system cache for reading the pixel data
from this buffer.
Change-Id: Iff92a453a36d4a60b5a0162832eebd5e8739b5c3
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
Add a custom cache_enable property in writeback connector to allow
user-mode to control the cache setting on a frame basis. Configure
the hw and activate/deactivate the llcc based on the property. The
custom property is added based on the availability of the system
cache for writeback.
Change-Id: I812b31955eb36c75c33ac279b56502a13f7cdcbf
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
Add a writeback connector property EARLY-FENCE-LINE to give usermode
the control on when to trigger the retire fence. This option is useful
in 2-pass composition, where the writeback triggers the retire-fence
early based on the prog-line which allows primary to start the fetch
before wb transaction is fully completed. This helps to keep the clks
and bw low. WB hardware generates the line-ptr-irq when wb output reaches
the configured prog-line. Retire fence is triggered based on the irq by
default and wb-done handles for cases where line-ptr-irq is missed.
Change-Id: I20867979693dc3447f77da24cd7e88305947fb6d
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
This change deprecates idle notify work for video mode
since idle timer will be maintained by userspace.
As part of idle notify work, syscache state is changed from
CACHE_STATE_NORMAL to CACHE_STATE_PRE_CACHE along with
notifying to the userspace. This change removes
CACHE_STATE_PRE_CACHE in the state machine and state is
updated from CACHE_STATE_NORMAL to CACHE_STATE_FRAME_WRITE
whenever the cache property is set.
Change-Id: If3b2c34be954cb625aca76da81fd854c077a8250
Signed-off-by: Yashwanth <yvulapu@codeaurora.org>
Many upstream files and APIs have been removed in downstream
driver. Some function definintions are left dangling without
any caller. Remove the functions which are not used downstream.
Change-Id: I9f936e7cdac3be6f854b3c67725164fad785f0d4
Signed-off-by: Steve Cohen <quic_cohens@quicinc.com>
Update msm_gem and msm_drv to comply with latest 5.15 kernel.
Modify dma_buf_vmap() and dma-buf's vmap callback to use
struct dma_buf_map. Rename dma_resv_get_excl_rcu to _unlocked.
Remove deprecated GEM and PRIME callbacks.
Change-Id: Ifdfc7f872c988d8455f465e7d17dfbcf212bb5f6
Signed-off-by: Bruce Hoo <bingchua@codeaurora.org>
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Move thread priority call to kernel worker thread because
component bind API may run from vendor_modeprobe process
context when all drivers probe succeed. Thread priority
update is not allowed from vendor_modeprobe process
context.
Change-Id: Iafac97ce02942d6a2134495232f3c395ba4a362f
Signed-off-by: Dhaval Patel <pdhaval@codeaurora.org>
Add new properties to support dynamically turning on and off digital
dimming and setting new minimum backlight.
Change-Id: I3b94190877d556768ba2c92ec59432dec44de0de
Signed-off-by: Ping Li <pingli@codeaurora.org>
Current DSC intial line calculation is giving extra line on top of
recommended value from systems since number of active soft slices
considered is wrong. Fix the number or usage of active soft slices
in an encoder to align dsc initial line with recommended setting.
Change-Id: I321260e22b7824b8c481a55b54831ce9535661cc
Signed-off-by: Prabhanjan Kandula <pkandula@codeaurora.org>
Currently the DP driver always uses a compression ratio of 3, if
DSC is enabled. So if the sink supports 30bpp, the compressed
output is set to 10bpp. But since the hardware supports
compressing this to 8bpp, it would require less link bandwidth
than 10bpp compressed output. For compliance testing, the
test equipment limits the link bandwidth based on the most
efficient compression ratio and for some resolutions there
is not enough link bandwidth for 3:1 compression.
This change always sets the compression output to 8bpp to
minimize the link bandwidth utilization.
Change-Id: Ifa6129444c2bab4e9c357ddfe49f76efa5b04be0
Signed-off-by: Rajkumar Subbiah <rsubbia@codeaurora.org>
This change adds support for qsync min refresh rate per
timing mode and populates qsync min refresh rate based
on the current fps when qsync is enabled.
Change-Id: I191d1d72e95dd065c8c0b56a6100104c00c6d8f6
Signed-off-by: Yashwanth <yvulapu@codeaurora.org>
Currently when RFI is used on a video mode panel the horizontal or
vertical front porch values can be adjusted to maintain a constant FPS.
When this feature is enabled, driver is not propagating the new
htotal or vtotal values to usermode for accurate BW and MDP clock
calculation, which may lead to underrun in some usecase.
This change publishes beforehand all the RFI related timing
such as compensation type, hfp or vfp and clock values for
each mode for accurate BW and clock calculation.
Change-Id: Ib89c5e318fe978b0ae2215dedc430e057a9a81b9
Signed-off-by: Amine Najahi <anajahi@codeaurora.org>
Add a new connector property to allow DC dimming feature to set
dimming backlight LUT. This change also adds a connector event
for client to register for backlight info needed for digital dimming
feature, including OS brightness, OS brightness_max, panel_backlight,
panel_backlight_max, and scale factors from ABA and LTM features.
Change-Id: I78f713fb2b965ca24effd973b4dfa9ff07a852f8
Signed-off-by: Ping Li <pingli@codeaurora.org>
This change adds logic to determine dsc switch based on
the connector property "CONNECTOR_PROP_DSC_MODE" and
performs seamless DSC switch if there is any change in
DSC configuration. The connector property is populated
in msm_sub_mode based on which suitable mode is selected.
Change-Id: Ifc4931f16dfb814781bc1d72b103e09103e6bfee
Signed-off-by: Yashwanth <yvulapu@codeaurora.org>
For higher refresh, to provide higher transfer time we need to disable
RSC solver in MDP. This can be configured through the panel timing node
devicetree property. This change adds the parsing of the devicetree
property.
Change-Id: I9e708325da35086d2f955cbcc80bb164ccb116cd
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
In dumping display registers, physical address will be appended after
each block name. This is to support register compare between kernel
and UEFI.
Change-Id: Ic20d3e2bd4c95aa7c71c4b646a149f7e83ad731a
Signed-off-by: Yu Wu <zwy@codeaurora.org>
Add support to send a data packet of info, written to
predefined buffers, providing information about each submitted frame.
Add required UAPI definitions for frame data buffers and event
notification.
Add support to read ubwc statistics from hw, based on defined rois.
Change-Id: I51f279de98ae4e2a02b0df6943d334764011d5db
Signed-off-by: Nilaan Gunabalachandran <ngunabal@codeaurora.org>
Some panels require a fixed step rate for a particular mode.
This change allows DSI panels to specify a single supported
step rate for each nominal fps rate which SDE will enforce
during atomic check of AVR parameters.
Change-Id: I049415449bc88ccd396fced16d4534251eac3a06
Signed-off-by: Steve Cohen <cohens@codeaurora.org>
Add AVR step support so SW can trigger a late frame and instead
of immediately triggering, HW will perform the update at the
start of the next step interval. This allows for a fixed SW
vsync timeline to be maintained in userland, eliminating the
usual drift from the actual HW vsync caused by a late frame.
This change adds AVR_STEP support via a DRM property.
Change-Id: I4cf8a296989805f134c2165a3bed0b050bb09c96
Signed-off-by: Steve Cohen <cohens@codeaurora.org>
Now that we don't need struct_mutex in the free path, we can get rid of
the asynchronous free all together.
Change-Id: I82406450e3a5d0d49d3fb753c621f55e8f4af088
Signed-off-by: Rob Clark <robdclark@chromium.org>
Git-commit: c951a9b284b907604759628d273901064c60d09f
Git-repo: git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git
Signed-off-by: Samantha Tran <samtran@codeaurora.org>
Rather than relying on the big dev->struct_mutex hammer, introduce a
more specific lock for protecting the bo lists.
Change-Id: I4c876a1c3ae51ff62372703a99a8daff0c4a7950
Signed-off-by: Rob Clark <robdclark@chromium.org>
Git-commit: d984457b31c4c53d2af374d5e78b3eb64debd483
Git-repo: git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git
[samtran@codeaurora.org: avoid changes related to debugfs and shrinker]
Signed-off-by: Samantha Tran <samtran@codeaurora.org>
We use a llist and a worker to delay the object cleanup. This avoids
taking mmap_sem and struct mutex in the wrong order when calling
drm_gem_object_put-unlocked() from drm_gem_mmap().
Fixes lockdep problem with copy_from_user() in msm_ioctl_gem_submit().
Change-Id: Idfe54ae8108158b69f3835f26991642d1e21f8ee
Signed-off-by: Kristian H. Kristensen <hoegsberg@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Git-commit: 48e7f18392c66f9b69ebac11c54f1a2e033ced54
Git-repo: git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git
[samtran@codeaurora.org: resolve trivial merge conflict]
Signed-off-by: Samantha Tran <samtran@codeaurora.org>
Add cwb dither support.
Catalog: Read dtsi value of cwb dither in pp parse part.
Wb: Install blob property for cwb dither.
Wb hw: Adds a new wb ops function to program cwb dither hardware.
CRTC: To ensure that userspace can check whether cwb dither is supported,
added "has_cwb_dither" to sde kms info.
PingPong: In order to reuse dither's map array, move dither_depth_map array
to pp header file.
Change-Id: I77e6a052a00b7c649452103145e5d7b4c8deb3a2
Signed-off-by: Yuchao Ma <yuchaom@codeaurora.org>
Currently, RFI feature only supports panel that contains
a single timing node. This limits the feature availability
for panel with multiple modes or with DFPS support.
This change adds support for RFI on panels that contains
multiple timing nodes.
Change-Id: I3a7aadf7b6da3518350b2eb815602b13b5c259f5
Signed-off-by: Amine Najahi <anajahi@codeaurora.org>
Add a new connector range property and a new entry to the panel
capability blob to publish the list of supported RFI frequencies.
In addition, add the required functions to set, validate and update
DSI bit clock rate value to trigger an internal seamless mode switch
and reconfigure DSI clock and PLL.
Change-Id: I7d19cc369f8c5528709f2f20a51ef02180ebdea4
Signed-off-by: Amine Najahi <anajahi@codeaurora.org>
Fix dlkm compilation errors that are due to the use of -Werror
flags used by the build system.
Change-Id: I5e1e9bc63c1361d73e4930aab123212717872ecb
Signed-off-by: Tatenda Chipeperekwa <tatendac@codeaurora.org>
Add changes to install retire fence offset property
and this configurable offset property can be used
to create speculative retire fences.
Change-Id: I0b5bf9bab5bfb811ddbc7a3e8813a3e801272d41
Signed-off-by: Jayaprakash Madisetty <jmadiset@codeaurora.org>
DPU has added support for noise injection into the layer stack. Change
adds support for noise layer programming and exposes the hardware block
to the user space modules.
Change-Id: Id176eea54fcdcd5d399457b14133a1ccde07299f
Introduce support for the FP16 format and FP16 color processing
blocks. This includes support for FP16, FP16 UBWC, and inline
rotation on tiled FP16 pixel data.
Change-Id: I06a70cab5447140598682f687129d4f8662524b2
Signed-off-by: Christopher Braga <cbraga@codeaurora.org>
Expose panel mode from kernel to SDM with SDE connector property
CONNECTOR_PROP_MODE_INFO and set panel mode from SDM to kernel
with SDE connector property CONNECTOR_PROP_SET_PANEL_MODE for
avoiding private change in upstream code in QGKI kernel.
Change-Id: I0629dad9399967cc1118ac02ce30597076ca367d
Signed-off-by: Lei Chen <chenlei@codeaurora.org>
Move away from the private and private_flags fields from drm_mode,
as it is being deprecated in latest kernel version. Instead, Add
msm_display_mode as a wrapper to be used in downstream to store these
parameters. Also, store msm_mode in connector_state to be accessed
in commit path.
Change-Id: Ia5bdebe75f00aa15fb7db4dc3a0d50c30894a95c
Signed-off-by: Orion Brody <obrody@codeaurora.org>
Commit a25b988ff83f ("drm/bridge: Extend bridge API to
disable connector creation") and commit ee68c743f8d0 ("drm: Stop
including drm_bridge.h from drm_crtc.h) add additional input flags.
This change adds fixes to the drm bridge attach API and includes
relevant drm_bridge header files.
Change-Id: I85e84eaff7df2995243896108a217fae81716b63
Signed-off-by: Samantha Tran <samtran@codeaurora.org>
Signed-off-by: Nilaan Gunabalachandran <ngunabal@codeaurora.org>
This change fixes the detection logic for overriding the ich
reset in both single and dual dsc case. In the previous logic
ich reset override was not getting triggered when partial update
on single dsc was enabled. This override is required to change the
default Hw behavior of changing the ich reset position.
ICH reset needs to be overridden in dual dsc merge case when
partial update disables the dsc merge and no. of slices per
encoder drops to 1. Similarly for single dsc case partial update
case when DSC encoder configuration changes from 2 slices to
single slice this override is required.
Change-Id: I435dc7ff10c9fb0edb8e40e6701608aa22136981
Signed-off-by: Abhijit Kulkarni <kabhijit@codeaurora.org>
In current implementation qsync min fps is single value.
It is same for all the list of supported dfps list.
Added support for new dt entry dsi-supported-qsync-min-fps-list
corresponding to the fps supported in the dfps list
dsi-supported-dfps-list.
Change-Id: Ifd5309c2f51865a3c0d9fadb65cbcd291b6ef42b
Signed-off-by: Raviteja Tamatam <travitej@codeaurora.org>
Due to power-domain, if rotator driver is registered early,
probe might get deferred several times and get stuck
indefinitely. So, this change adds driver registration
after genpd init to handle such cases.
Change-Id: I8dcb640d0ab0cdf0818cbce1b1fb460c28d8b9e7
Signed-off-by: Yashwanth <yvulapu@codeaurora.org>
It is not applicable for all DFPS cases to update UIDLE state
according to current frame rate. If DFPS changes frame rate
through vertical front porch values, the SDE clocks and transfer
time will not get changed accordingly, and it always get fixed
at max frame rate configuration of DFPS.
Add this change to check max FPS of DFPS instead of current
frame rate for UIDLE update, if DFPS is enabled with VFP.
Change-Id: I7634bce6a9eb1af212ba19a267735be08b20ae1f
Signed-off-by: Lei Chen <chenlei@codeaurora.org>
