[ Upstream commit df518a0ae1b982a4dcf2235464016c0c4576a34d ]
The buffer used to transfer data over the mailbox interface is mapped
using the client's device. This is incorrect, as the device performing
the DMA transfer is the mailbox itself. Fix it by using the mailbox
controller device instead.
This requires including the mailbox_controller.h header to dereference
the mbox_chan and mbox_controller structures. The header is not meant to
be included by clients. This could be fixed by extending the client API
with a function to access the controller's device.
Fixes: 4e3d60656a ("ARM: bcm2835: Add the Raspberry Pi firmware driver")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Stefan Wahren <wahrenst@gmx.net>
Tested-by: Ivan T. Ivanov <iivanov@suse.de>
Link: https://lore.kernel.org/r/20240326195807.15163-3-laurent.pinchart@ideasonboard.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e7c57355a3bc617fc220234889e49fe722a6305 ]
When unbinding the firmware device we need to make sure it has no
consumers left. Otherwise we'd leave them with a firmware handle
pointing at freed memory.
Keep a reference count of all consumers and introduce rpi_firmware_put()
which will permit automatically decrease the reference count upon
unbinding consumer drivers.
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Pull clk updates from Stephen Boyd:
"It looks like a smaller batch of clk updates this time around.
In the core framework we just have some minor tweaks and a debugfs
feature, so not much to see there. The driver updates are fairly well
split between AT91 and Qualcomm clk support. Adding those two drivers
together equals about 50% of the diffstat.
Otherwise, the big amount of work this time was on supporting
Broadcom's Raspberry Pi firmware clks.
Highlights:
Core:
- Document clk_hw_round_rate() so it gets some more use
- Remove unused __clk_get_flags()
- Add a prepare/enable debugfs feature similar to rate setting
New Drivers:
- Add support for SAMA7G5 SoC clks
- Enable CPU clks on Qualcomm IPQ6018 SoCs
- Enable CPU clks on Qualcomm MSM8996 SoCs
- GPU clk support for Qualcomm SM8150 and SM8250 SoCs
- Audio clks on Qualcomm SC7180 SoCs
- Microchip Sparx5 DPLL clk
- Add support for the new Renesas RZ/G2H (R8A774E1) SoC
Updates:
- Make defines for bcm63xx-gate clks to use in DT
- Support BCM2711 SoC firmware clks
- Add HDMI clks for BCM2711 SoCs
- Add RTC related clks on Ingenic SoCs
- Support USB PHY clks on Ingenic SoCs
- Support gate clks on BCM6318 SoCs
- RMU and DMAC/GPIO clock support for Actions Semi S500 SoCs
- Use poll_timeout functions in Rockchip clk driver
- Support Rockchip rk3288w SoC variant
- Mark mac_lbtest critical on Rockchip rk3188
- Add CAAM clock support for i.MX vf610 driver
- Add MU root clock support for i.MX imx8mp driver
- Amlogic g12: add neural network accelerator clock sources
- Amlogic meson8: remove critical flag for main PLL divider
- Amlogic meson8: add video decoder clock gates
- Convert one more Renesas DT binding to json-schema
- Enhance critical clock handling on Renesas platforms to only
consider clocks that were enabled at boot time"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (79 commits)
clk: qcom: gcc: Make disp gpll0 branch aon for sc7180/sdm845
ipq806x: gcc: add support for child probe
clk: qcom: msm8996: Make symbol 'cpu_msm8996_clks' static
clk: qcom: ipq8074: Add correct index for PCIe clocks
clk: <linux/clk-provider.h>: drop a duplicated word
clk: renesas: cpg-mssr: Add r8a774e1 support
dt-bindings: clock: renesas,cpg-mssr: Document r8a774e1
clk: Drop duplicate selection in Kconfig
clk: qcom: smd: Add support for MSM8992/4 rpm clocks
clk: qcom: ipq8074: Add missing clocks for pcie
dt-bindings: clock: qcom: ipq8074: Add missing bindings for PCIe
Replace HTTP links with HTTPS ones: Common CLK framework
clk: qcom: Add CPU clock driver for msm8996
dt-bindings: clk: qcom: Add bindings for CPU clock for msm8996
soc: qcom: Separate kryo l2 accessors from PMU driver
clk: meson: meson8b: add the vclk2_en gate clock
clk: meson: meson8b: add the vclk_en gate clock
clk: qcom: Fix return value check in apss_ipq6018_probe()
clk: bcm: dvp: Add missing module informations
clk: meson: meson8b: Drop CLK_IS_CRITICAL from fclk_div2
...
The Raspberry Pi 4 gets its USB functionality from VL805, a PCIe chip
that implements xHCI. After a PCI reset, VL805's firmware may either be
loaded directly from an EEPROM or, if not present, by the SoC's
co-processor, VideoCore. RPi4's VideoCore OS contains both the non public
firmware load logic and the VL805 firmware blob. The function this patch
introduces triggers the aforementioned process.
Link: https://lore.kernel.org/r/20200505161318.26200-3-nsaenzjulienne@suse.de
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Since clk-raspberrypi is tied to the VC4 firmware instead of particular
hardware it's registration should be performed by the firmware driver.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The firmware-owned GPIO expander on RPi 3 B+ must be in same state
after a reboot as initial power on. Otherwise this would cause a
network boot failure of the BOOTROM. So inform the VC4 firmware to restore
the expander before doing a reboot.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Phil Elwell <phil@raspberrypi.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Adopt the SPDX license identifier headers to ease license compliance
management.
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Commit a1547e0bca ("firmware: raspberrypi: Remove VLA usage")
moved away from VLA's to a fixed maximum size for mailbox data.
However, some mailbox calls use larger data buffers
than the maximum allowed in that change. This fix therefor
moves from using fixed buffers to kmalloc to ensure all sizes
are catered for.
There is some documentation, which is somewhat out of date,
on the mailbox calls here :
https://github.com/raspberrypi/firmware/wiki/Mailbox-property-interface
Fixes: a1547e0bca ("firmware: raspberrypi: Remove VLA usage")
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
We should never assume to get a reply from the firmware otherwise
the call could block forever and the user don't get informed. So
define a timeout of 1 sec and print a stacktrace once in the unlikely
case the timeout expired.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
In the quest to remove all stack VLA usage from the kernel[1], this
removes the VLA in favor of a maximum size and adds a sanity check.
Existing callers of the firmware interface never need more than 24
bytes (struct gpio_set_config). This chooses 32 just to stay ahead
of future growth.
v2: Fix the length passed to rpi_firmware_property_list (by anholt,
acked by Kees).
[1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Since the raspberrypi-hwmon driver is tied to the VC4 firmware instead of
particular hardware its registration should be in the firmware driver.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The firmware timestamp is an unsigned 32-bit value, but we copy it into
a signed 32-bit variable, so we can theoretically get an overflow in
the calculation when the timestamp is between 2038 and 2106.
This changes the temporary variable to time64_t and changes the deprecated
time_to_tm() over to time64_to_tm() accordingly.
There is still an overflow in y2106, but that is a limitation of the
firmware interface, not a kernel problem.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
This gives us a function for making mailbox property channel requests
of the firmware, which is most notable in that it will let us get and
set clock rates.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
