Pull ARM SoC fixes from Olof Johansson:
"Here's our last set of fixes for 3.17. Most of these are for TI
platforms, fixing some noisy Kconfig issues, runtime clock and power
issues on several platforms and NAND timings on DRA7.
There are also a couple of bug fixes for i.MX, one for QCOM and a
small fix to avoid section mismatch noise on PXA.
Diffstat looks large, partially due to some tables being updated and
thus touching many lines. The qcom gsbi change also restructures
clock management a bit and thus touches a bunch of lines.
All in all, a bit more changes than we'd like at this point, but
nothing stands out as risky either so it seems like the right thing to
send it up now instead of holding it to the merge window"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
drivers/soc: qcom: do not disable the iface clock in probe
ARM: imx: fix .is_enabled() of shared gate clock
ARM: OMAP3: Fix I/O chain clock line assertion timed out error
ARM: keystone: dts: fix bindings for pcie and usb clock nodes
bus: omap_l3_noc: Fix connID for OMAP4
ARM: DT: imx53: fix lvds channel 1 port
ARM: dts: cm-t54: fix serial console power supply.
ARM: dts: dra7-evm: Fix NAND GPMC timings
ARM: pxa: fix section mismatch warning for pxa_timer_nodt_init
ARM: OMAP: Fix Kconfig warning for omap1
Pull devicetree bug fixes and documentation from Grant Likely:
"Several bug fix commits for issues found in the v3.17 rc series.
Most of these are minor in that they aren't actively dangerous, but
they have been seen in the wild. The one important fix is commit
7dbe5849fb ("of: make sure of_alias is initialized before accessing
it"), without which some powerpc platforms will fail to find stdout
for the console"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux:
of/fdt: fix memory range check
of: Fix memory block alignment in early_init_dt_add_memory_arch()
of: make sure of_alias is initialized before accessing it
of: Documentation regarding attaching OF Selftest testdata
of: Disabling OF functions that use sysfs if CONFIG_SYSFS disabled
of: correct of_console_check()'s return value
Pull sound fixes from Takashi Iwai:
"All small fixes in random various drivers, mostly for ASoC at this
time, which look reasonable for a high rc number"
* tag 'sound-3.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: rockchip-i2s: dt: swap tx and rx channed request number in example
ASoC: rockchip-i2s: fix registers' property of rockchip i2s controller
ASoC: rockchip-i2s: fix master mode set bit error
ASoC: cs4265: Fix register address to set the proper data type.
ALSA: hda - Fix invalid pin powermap without jack detection
ASoC: soc-pcm: fix dpcm_path_get error handling
ASoC: samsung-i2s: Check secondary DAI exists before referencing
ASoC: Update email id of the author
ASoC: dwc: Update email id of the author
ASoC: davinci-mcasp: Correct rx format unit configuration
ASoC: tlv320aic31xx: Fix 24bit samples with I2S format and 12MHz mclk
Pull spi fixes from Mark Brown:
"A few driver specific fixes for v3.17:
- Fix davinci so that GPIO chip selects work with deferred probe of
GPIOs (which could happen in production depending on kernel config)
plus one incremental stylistic fix to that.
- Several fixes for the newly introduced rockchip driver that came up
in wider testing of the device.
- A couple of small things in the sirf driver, one bug that would
stop DMA transfers working and another update to follow the
documented procedure in the datasheet.
- Fix some memory leaks with devm_kzalloc() being used outside of the
device bind path"
* tag 'spi-v3.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: davinci: remove empty function davinci_spi_cleanup
spi: davinci: request cs_gpio's from probe
spi/pl022: Fix error message
spi/rockchip: Mark DMA as optional
spi/rockchip: Don't warn if SPI is busy but disabled
spi/rockchip: Fix the wait_for_idle() timeout
spi: sirf: add fifo reset/start for cmd transfer
spi: sirf: enable RX_IO_DMA_INT interrupt
spi: dw: Don't use devm_kzalloc in master->setup callback
spi: fsl: Don't use devm_kzalloc in master->setup callback
Pull input updates from Dmitry Torokhov:
"A few quirks for i8042/AT keyboards and a small device tree doc fix
for Atmel Touchscreens"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: atmel_mxt_ts - fix merge in DT documentation
Input: i8042 - also set the firmware id for MUXed ports
Input: i8042 - add nomux quirk for Avatar AVIU-145A6
Input: i8042 - add Fujitsu U574 to no_timeout dmi table
Input: atkbd - do not try 'deactivate' keyboard on any LG laptops
Reference to RK3288 TRM, fix an error channel id for i2s tx and rx
Table 10-1 DMAC_BUS Request Mapping Table
Req number Source Polarity
0 I2S tx High level
1 I2S rx High level
Tested on RK3288 board.
Signed-off-by: Jianqun <jay.xu@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull USB fixes from Greg KH:
"Here are some USB and PHY fixes for 3.17-rc5.
Nothing major here, just a number of tiny fixes for reported issues,
and some new device ids as well.
All have been tested in linux-next"
* tag 'usb-3.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (46 commits)
xhci: fix oops when xhci resumes from hibernate with hw lpm capable devices
usb: xhci: Fix OOPS in xhci error handling code
xhci: Fix null pointer dereference if xhci initialization fails
storage: Add single-LUN quirk for Jaz USB Adapter
uas: Add missing le16_to_cpu calls to asm1051 / asm1053 usb-id check
usb: chipidea: msm: Initialize PHY on reset event
usb: chipidea: msm: Use USB PHY API to control PHY state
usb: hub: take hub->hdev reference when processing from eventlist
uas: Disable uas on ASM1051 devices
usb: dwc2/gadget: avoid disabling ep0
usb: dwc2/gadget: delay enabling irq once hardware is configured properly
usb: dwc2/gadget: do not call disconnect method in pullup
usb: dwc2/gadget: break infinite loop in endpoint disable code
usb: dwc2/gadget: fix phy initialization sequence
usb: dwc2/gadget: fix phy disable sequence
uwb: init beacon cache entry before registering uwb device
USB: ftdi_sio: Add support for GE Healthcare Nemo Tracker device
USB: document the 'u' flag for usb-storage quirks parameter
usb: host: xhci: fix compliance mode workaround
usb: dwc3: fix TRB completion when multiple TRBs are started
...
Pull fbdev fixes from Tomi Valkeinen:
"Minor fixes for amba-clcd and video DT bindings"
* tag 'fbdev-fixes-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
video: ARM CLCD: Fix color model capabilities for DT platforms
video: fix composite video connector compatible string
Pull dmaengine fixes from Vinod Koul:
"Two minor fixes.
First one from Kuninori clarifying dmas bindings and second from Lars
for fixing dma descriptor completion in non cyclic case"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: jz4740: Fix non-cyclic descriptor completion
dt/bindings: rcar-audmapp: tidyup dmas explanation
using LVDS channel 1 on an i.MX53 leads to following error:
imx-ldb 53fa8008.ldb: unable to set di0 parent clock to ldb_di1
This comes from imx_ldb_set_clock with mux = 0. Mux parameter must be "1" for
reparenting di1 clock to ldb_di1. The value of the mux param comes from device
tree port settings.
On i.MX5, the internal two-input-multiplexer is used. Due to hardware limitations,
only one port (port@[0,1]) can be used for each channel (lvds-channel@[0,1],
respectively)
Documentation update suggested by Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Fixes: e05c8c9a79 ("ARM: dts: imx53: Add IPU DI ports and endpoints, move imx-drm node to dtsi")
Cc: <stable@vger.kernel.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch add a document that explains how the selftest test data is
dynamically attached into the live device tree irrespective of the
machine's architecture.
Signed-off-by: Gaurav Minocha <gaurav.minocha.os@gmail.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Pull networking fixes from David Miller:
1) Fix skb leak in mac802154, from Martin Townsend
2) Use select not depends on NF_NAT for NFT_NAT, from Pablo Neira
Ayuso
3) Fix union initializer bogosity in vxlan, from Gerhard Stenzel
4) Fix RX checksum configuration in stmmac driver, from Giuseppe
CAVALLARO
5) Fix TSO with non-accelerated VLANs in e1000, e1000e, bna, ehea,
i40e, i40evf, mvneta, and qlge, from Vlad Yasevich
6) Fix capability checks in phy_init_eee(), from Giuseppe CAVALLARO
7) Try high order allocations more sanely for SKBs, specifically if a
high order allocation fails, fall back directly to zero order pages
rather than iterating down one order at a time. From Eric Dumazet
8) Fix a memory leak in openvswitch, from Li RongQing
9) amd-xgbe initializes wrong spinlock, from Thomas Lendacky
10) RTNL locking was busted in setsockopt for anycast and multicast, fix
from Sabrina Dubroca
11) Fix peer address refcount leak in ipv6, from Nicolas Dichtel
12) DocBook typo fixes, from Masanari Iida
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (101 commits)
ipv6: restore the behavior of ipv6_sock_ac_drop()
amd-xgbe: Enable interrupts for all management counters
amd-xgbe: Treat certain counter registers as 64 bit
greth: moved TX ring cleaning to NAPI rx poll func
cnic : Cleanup CONFIG_IPV6 & VLAN check
net: treewide: Fix typo found in DocBook/networking.xml
bnx2x: Fix link problems for 1G SFP RJ45 module
3c59x: avoid panic in boomerang_start_xmit when finding page address:
netfilter: add explicit Kconfig for NETFILTER_XT_NAT
ipv6: use addrconf_get_prefix_route() to remove peer addr
ipv6: fix a refcnt leak with peer addr
net-timestamp: only report sw timestamp if reporting bit is set
drivers/net/fddi/skfp/h/skfbi.h: Remove useless PCI_BASE_2ND macros
l2tp: fix race while getting PMTU on PPP pseudo-wire
ipv6: fix rtnl locking in setsockopt for anycast and multicast
VMXNET3: Check for map error in vmxnet3_set_mc
openvswitch: distinguish between the dropped and consumed skb
amd-xgbe: Fix initialization of the wrong spin lock
openvswitch: fix a memory leak
netfilter: fix missing dependencies in NETFILTER_XT_TARGET_LOG
...
Pull regulator documentation fixes from Mark Brown:
"All the fixes people have found for the regulator API have been
documentation fixes, avoiding warnings while building the kerneldoc,
fixing some errors in one of the DT bindings documents and fixing some
typos in the header"
* tag 'regulator-v3.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: fix kernel-doc warnings in header files
regulator: Proofread documentation
regulator: tps65090: Fix tps65090 typos in example
The Rockchip SPI controller works fine without DMA (aside from a few
warnings). The DMA property even implies this, saying:
DMA request names should include "tx" and "rx" if present.
Officially mark the properties as optional.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull sound fixes from Takashi Iwai:
"This time it contains a bunch of small ASoC fixes that slipped from in
previous updates, in addition to the usual HD-audio fixes and the
regression fixes for FireWire updates in 3.17.
All commits are reasonably small fixes"
* tag 'sound-3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix COEF setups for ALC1150 codec
ASoC: simple-card: Fix bug of wrong decrement DT node's refcount
ALSA: hda - Fix digital mic on Acer Aspire 3830TG
ASoC: omap-twl4030: Fix typo in 2nd dai link's platform_name
ALSA: firewire-lib/dice: add arrangements of PCM pointer and interrupts for Dice quirk
ALSA: dice: fix wrong channel mappping at higher sampling rate
ASoC: cs4265: Fix setting of functional mode and clock divider
ASoC: cs4265: Fix clock rates in clock map table
ASoC: rt5677: correct mismatch widget name
ASoC: rt5640: Do not allow regmap to use bulk read-write operations
ASoC: tegra: Fix typo in include guard
ASoC: da732x: Fix typo in include guard
ASoC: core: fix .info for SND_SOC_BYTES_TLV
ASoC: rcar: Use && instead of & for boolean expressions
ASoC: Use dev_set_name() instead of init_name
ASoC: axi: Fix ADI AXI SPDIF specification
Pull input subsystem updates from Dmitry Torokhov:
"A fix for MT breakage, enhancement to Elantech PS/2 driver and a
couple of assorted fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - add support for trackpoint found on some v3 models
Input: elantech - reset the device when elantech probe fails
Input: ALPS - suppress message about 'Unknown touchpad'
Input: fix used slots detection breakage
Input: sparc - i8042-sparcio.h: fix unused kbd_res warning
Input: atmel_mxt_ts - improve description of gpio-keymap property
The quite-recently-added analog-tv-connector bindings say that the
compatible string for composite video connector is
"composite-connector". That string is also used in the omap3-n900.dts
file. However, the connector driver uses "composite-video-connector", so
this has never worked.
While changing the driver's compatible string to "composite-connector"
would be safer, as published DT bindings should not be changed, I'd
rather fix the bindings in this case for two reasons:
* composite-connector is a bit too generic name, as it doesn't even hint
at video.
* it's clear that this has never worked, which means no one has used
those bindings, which should make it safe to change this.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Pull ARM SoC fixes from Olof Johansson:
"Here's the weekly batch of fixes from arm-soc.
The delta is a largeish negative delta, due to revert of SMP support
for Broadcom's STB SoC -- it was accidentally merged before some
issues had been addressed, so they will make a new attempt for 3.18.
I didn't see a need for a full revert of the whole platform due to
this, we're keeping the rest enabled.
The rest is mostly:
- a handful of DT fixes for i.MX (Hummingboard/Cubox-i in particular)
- some MTD/NAND fixes for OMAP
- minor DT fixes for shmobile
- warning fix for UP builds on vexpress/spc
There's also a couple of patches that wires up hwmod on TI's DRA7 SoC
so it can boot. Drivers and the rest had landed for 3.17, and it's
small and isolated so it made sense to pick up now even if it's not a
bugfix"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
vexpress/spc: fix a build warning on array bounds
ARM: DRA7: hwmod: Add dra74x and dra72x specific ocp interface lists
ARM: DRA7: Add support for soc_is_dra74x() and soc_is_dra72x() variants
MAINTAINERS: catch special Rockchip code locations
ARM: dts: microsom-ar8035: MDIO pad must be set open drain
ARM: dts: omap54xx-clocks: Fix the l3 and l4 clock rates
ARM: brcmstb: revert SMP support
ARM: OMAP2+: hwmod: Rearm wake-up interrupts for DT when MUSB is idled
ARM: dts: Enable UART wake-up events for beagleboard
ARM: dts: Remove twl6030 clk32g "regulator"
ARM: OMAP2+: omap_device: remove warning that clk alias already exists
ARM: OMAP: fix %d confusingly prefixed with 0x in format string
ARM: dts: DRA7: fix interrupt-cells for GPIO
mtd: nand: omap: Fix 1-bit Hamming code scheme, omap_calculate_ecc()
ARM: dts: omap3430-sdp: Revert to using software ECC for NAND
ARM: OMAP2+: GPMC: Support Software ECC scheme via DT
mtd: nand: omap: Revert to using software ECC by default
ARM: dts: hummingboard/cubox-i: change SPDIF output to be more descriptive
ARM: dts: hummingboard/cubox-i: add USB OC pinctrl configuration
ARM: shmobile: r8a7791: add missing 0x0100 for SDCKCR
...
The PTP reference clock, used for setting the addend in the Timestamp Addend
Register, was erroneously hard-coded (as reported in the databook just as
example).
The patch removes the macro named: STMMAC_SYSCLOCK and allows to use a
reference clock (clk_ptp_ref_i) that can be passed from the platform.
If not passed, the main driver clock will be used as default; note that
this can be fine on some platforms.
Note that, prior this patch, using the old STMMAC_SYSCLOCK on some platforms,
as side effect, the ptp clock can move faster/slower than the system clock.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull mfd fixes from Lee Jones:
"Couple of simple fixes due for the 3.17 rcs
(and a sneaky document addition that slipped from the previous
pull-request)"
* tag 'mfd-fixes-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: twl4030-power: Fix PM idle pin configuration to not conflict with regulators
mfd: tc3589x: Add device tree bindings
mfd: ab8500-core: Use 'ifdef' for config options
mfd: htc-i2cpld: Fix %d confusingly prefixed with 0x in format string
mfd: omap-usb-host: Fix %d confusingly prefixed with 0x in format string
Pull pin-control fixes from Linus Walleij:
"My first (a bit delayed) pack of pin control fixes for the v3.17
series, only driver fixes:
- SH-PFC (Renesas) r8a7791 CAN bus pin group problem
- Rockchip (GPIO0 configuration)
- Tegra-xusb (interrupt handling)
- Exynos (GPIO interrupt locking)
- Qualcomm (fix misleading example interrupts)
- minor non-critical fixes for abx500 and AT91 also sneaked in,
because I initially intended this pull for post RC-1, hope it's
still OK"
* tag 'pinctrl-v3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: qcom: apq8064: Correct interrupts in example
pinctrl: exynos: Lock GPIOs as interrupts when used as EINTs
pinctrl: pinctrl-at91.c: fix decimal printf format specifiers prefixed with 0x
pinctrl: abx500: remove useless check
pinctrl: tegra-xusb: testing wrong variable in probe()
pinctrl: tegra-xusb: fix an off by one test
pinctrl: rockchip: fix rk3288 gpio0 configuration
sh-pfc: r8a7791: fix CAN pin groups
This defines the device tree bindings for the Toshiba TC3589x
series of multi-purpose expanders. Only the stuff I can test
is defined: GPIO and keypad. Others may implement more
subdevices further down the road.
This is to complement
commit a435ae1d51
"mfd: Enable the tc3589x for Device Tree" which left off
the definition of the device tree bindings.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
For v3.14 and prior, 1-bit Hamming code ECC via software was the
default choice for some boards e.g. 3430sdp.
Commit ac65caf514 in v3.15 changed the behaviour
to use 1-bit Hamming code via Hardware using a different ECC layout
i.e. (ROM code layout) than what is used by software ECC.
This ECC layout change causes NAND filesystems created in v3.14
and prior to be unusable in v3.15 and later. So don't mark "sw" scheme
as deperecated and support it.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The example in the binding document indicates that interrupt 32 is used
for the TLMM summary IRQ. Correct this to reduce the confusion.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The below patch improves the documentation for the gpio-property. Stephen
Warren has a good example here:
https://github.com/swarren/linux-tegra/commit/09789801
trackpad@4b {
compatible = "atmel,maxtouch";
reg = <0x4b>;
interrupt-parent = <&gpio>;
interrupts = <TEGRA_GPIO(W, 3) IRQ_TYPE_LEVEL_LOW>;
linux,gpio-keymap = <0 0 0 BTN_LEFT>;
};
This maps BTN_LEFT to the 4th bit of the T19 message.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull PCI changes from Bjorn Helgaas:
"Marvell MVEBU
- Remove ARCH_KIRKWOOD dependency (Andrew Lunn)
NVIDIA Tegra
- Add debugfs support (Thierry Reding)
Synopsys DesignWare
- Look for configuration space in 'reg', not 'ranges' (Kishon Vijay Abraham I)
- Program ATU with untranslated address (Kishon Vijay Abraham I)
- Add config access-related pcie_host_ops for v3.65 hardware (Murali Karicheri)
- Add MSI-related pcie_host_ops for v3.65 hardware (Murali Karicheri)
TI DRA7xx
- Add TI DR7xx PCIe driver (Kishon Vijay Abraham I)"
* tag 'pci-v3.17-changes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: designware: Add MSI-related pcie_host_ops for v3.65 hardware
PCI: designware: Add config access-related pcie_host_ops for v3.65 hardware
PCI: dra7xx: Add TI DRA7xx PCIe driver
PCI: designware: Program ATU with untranslated address
PCI: designware: Look for configuration space in 'reg', not 'ranges'
PCI: tegra: Add debugfs support
PCI: mvebu: Remove ARCH_KIRKWOOD dependency
The specification requires compatible = "adi,axi-spdif-1.00.a" but
driver and example and file name indicate "adi,axi-spdif-tx-1.00.a".
Change the specification to match the implementation.
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Fixes: d7b528eff9 ("dt: Add bindings documentation for the ADI AXI-SPDIF audio controller")
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
In case the Device Tree blob passed by the boot agent supplies both an
'interrupts-extended' and an 'interrupts' property in order to allow for
older kernels to be usable, prefer the new-style 'interrupts-extended'
property which conveys a lot more information.
This allows us to have bootloaders willingly maintaining backwards
compatibility with older kernels without entirely deprecating the
'interrupts' property.
Update the bindings documentation to describe a situation where both the
'interrupts-extended' and the 'interrupts' property are present, and
which one takes precedence over the other.
Cc: stable@vger.kernel.org # 3.13+
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Pull device tree updates from Grant Likely:
"The branch contains the following device tree changes the v3.17 merge
window:
Group changes to the device tree. In preparation for adding device
tree overlay support, OF_DYNAMIC is reworked so that a set of device
tree changes can be prepared and applied to the tree all at once.
OF_RECONFIG notifiers see the most significant change here so that
users always get a consistent view of the tree. Notifiers generation
is moved from before a change to after it, and notifiers for a group
of changes are emitted after the entire block of changes have been
applied
Automatic console selection from DT. Console drivers can now use
of_console_check() to see if the device node is specified as a console
device. If so then it gets added as a preferred console. UART
devices get this support automatically when uart_add_one_port() is
called.
DT unit tests no longer depend on pre-loaded data in the device tree.
Data is loaded dynamically at the start of unit tests, and then
unloaded again when the tests have completed.
Also contains a few bugfixes for reserved regions and early memory
setup"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux: (21 commits)
of: Fixing OF Selftest build error
drivers: of: add automated assignment of reserved regions to client devices
of: Use proper types for checking memory overflow
of: typo fix in __of_prop_dup()
Adding selftest testdata dynamically into live tree
of: Add todo tasklist for Devicetree
of: Transactional DT support.
of: Reorder device tree changes and notifiers
of: Move dynamic node fixups out of powerpc and into common code
of: Make sure attached nodes don't carry along extra children
of: Make devicetree sysfs update functions consistent.
of: Create unlocked versions of node and property add/remove functions
OF: Utility helper functions for dynamic nodes
of: Move CONFIG_OF_DYNAMIC code into a separate file
of: rename of_aliases_mutex to just of_mutex
of/platform: Fix of_platform_device_destroy iteration of devices
of: Migrate of_find_node_by_name() users to for_each_node_by_name()
tty: Update hypervisor tty drivers to use core stdout parsing code.
arm/versatile: Add the uart as the stdout device.
of: Enable console on serial ports specified by /chosen/stdout-path
...
Pull MMC updates from Ulf Hansson:
"Me and Chris Ball decided to try out using my MMC tree as the primary
one, to simplify handling of patches.
This pull does thus contains all the MMC patches for 3.17 rc1, no pull
from Chris this time.
Details:
MMC core:
- forward compatibility for eMMC
- fix some blacklisted cards with broken secure discard
MMC host:
- mmci: Add support for Qualcomm variant
- mmci: Fix regression for arm_variant
- sdhci: Various fixes and cleanups
- sdhci: Improve external VDD regulator support
- sdhci: Support for DDR50 1.8V mode for BayTrail
- sdhci-st: Add driver for ST SDHCI controller
- sh-mmcif: DMA fixes
- omap_hsmmc: Add support for SDIO interrupts
- sdhci-pci: Add support for Intel Quark X1000
- dw_mmc: Update the reset sequence
- s3cmci: port DMA code to dmaengine API"
* tag 'mmc-v3.17-1' of git://git.linaro.org/people/ulf.hansson/mmc: (67 commits)
mmc: dw_mmc: modify the dt-binding for removing slot-node and supports-highspeed
mmc: dw_mmc: Slot quirk "disable-wp" is deprecated.
mmc: mmci: Reverse IRQ handling for the arm_variant
mmc: mmci: Move all CMD irq handling to mmci_cmd_irq()
mmc: mmci: Remove redundant check of status for DATA irq
mmc: dw_mmc: change to use recommended reset procedure
mmc: sdhci-pxav3: Use devm_* managed helpers
mmc: tmio: Configure DMA slave bus width
mmc: sh_mmcif: Configure DMA slave bus width
mmc: sh_mmcif: Fix DMA slave address configuration
mmc: sh_mmcif: Document DT bindings
mmc: sdhci-pci: remove PCI PM functions in suspend/resume callback
mmc: Do not advertise secure discard if it is blacklisted
mmc: sdhci-msm: Get COMPILE_TEST support
mmc: sdhci-msm: Remove unnecessary header file inclusion
mmc: sdhci-msm: Fix the binding example
mmc: sdhci: add DDR50 1.8V mode support for BayTrail eMMC Controller
mmc: sdhci: Preset value not supported in Baytrail eMMC
mmc: MMC_USDHI6ROL0 should depend on HAS_DMA
mmc: MMC_SH_MMCIF should depend on HAS_DMA
...
Pull networking fixes from David Miller:
"Several networking final fixes and tidies for the merge window:
1) Changes during the merge window unintentionally took away the
ability to build bluetooth modular, fix from Geert Uytterhoeven.
2) Several phy_node reference count bug fixes from Uwe Kleine-König.
3) Fix ucc_geth build failures, also from Uwe Kleine-König.
4) Fix klog false positivies when netlink messages go to network
taps, by properly resetting the network header. Fix from Daniel
Borkmann.
5) Sizing estimate of VF netlink messages is too small, from Jiri
Benc.
6) New APM X-Gene SoC ethernet driver, from Iyappan Subramanian.
7) VLAN untagging is erroneously dependent upon whether the VLAN
module is loaded or not, but there are generic dependencies that
matter wrt what can be expected as the SKB enters the stack.
Make the basic untagging generic code, and do it unconditionally.
From Vlad Yasevich.
8) xen-netfront only has so many slots in it's transmit queue so
linearize packets that have too many frags. From Zoltan Kiss.
9) Fix suspend/resume PHY handling in bcmgenet driver, from Florian
Fainelli"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (55 commits)
net: bcmgenet: correctly resume adapter from Wake-on-LAN
net: bcmgenet: update UMAC_CMD only when link is detected
net: bcmgenet: correctly suspend and resume PHY device
net: bcmgenet: request and enable main clock earlier
net: ethernet: myricom: myri10ge: myri10ge.c: Cleaning up missing null-terminate after strncpy call
xen-netfront: Fix handling packets on compound pages with skb_linearize
net: fec: Support phys probed from devicetree and fixed-link
smsc: replace WARN_ON() with WARN_ON_SMP()
xen-netback: Don't deschedule NAPI when carrier off
net: ethernet: qlogic: qlcnic: Remove duplicate object file from Makefile
wan: wanxl: Remove typedefs from struct names
m68k/atari: EtherNEC - ethernet support (ne)
net: ethernet: ti: cpmac.c: Cleaning up missing null-terminate after strncpy call
hdlc: Remove typedefs from struct names
airo_cs: Remove typedef local_info_t
atmel: Remove typedef atmel_priv_ioctl
com20020_cs: Remove typedef com20020_dev_t
ethernet: amd: Remove typedef local_info_t
net: Always untag vlan-tagged traffic on input.
drivers: net: Add APM X-Gene SoC ethernet driver support.
...
This adds support for specifying the phy to be used with the fec in the
devicetree using the standard phy-handle property and also supports
fixed-link.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull slave-dma updates from Vinod Koul:
"Some notable changes are:
- new driver for AMBA AXI NBPF by Guennadi
- new driver for sun6i controller by Maxime
- pl330 drivers fixes from Lar's
- sh-dma updates and fixes from Laurent, Geert and Kuninori
- Documentation updates from Geert
- drivers fixes and updates spread over dw, edma, freescale, mpc512x
etc.."
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (72 commits)
dmaengine: sun6i: depends on RESET_CONTROLLER
dma: at_hdmac: fix invalid remaining bytes detection
dmaengine: nbpfaxi: don't build this driver where it cannot be used
dmaengine: nbpf_error_get_channel() can be static
dma: pl08x: Use correct specifier for size_t values
dmaengine: Remove the context argument to the prep_dma_cyclic operation
dmaengine: nbpfaxi: convert to tasklet
dmaengine: nbpfaxi: fix a theoretical race
dmaengine: add a driver for AMBA AXI NBPF DMAC IP cores
dmaengine: add device tree binding documentation for the nbpfaxi driver
dmaengine: edma: Do not register second device when booted with DT
dmaengine: edma: Do not change the error code returned from edma_alloc_slot
dmaengine: rcar-dmac: Add device tree bindings documentation
dmaengine: shdma: Allocate cyclic sg list dynamically
dmaengine: shdma: Make channel filter ignore unrelated devices
dmaengine: sh: Rework Kconfig and Makefile
dmaengine: sun6i: Fix memory leaks
dmaengine: sun6i: Free the interrupt before killing the tasklet
dmaengine: sun6i: Remove switch statement from buswidth convertion routine
dmaengine: of: kconfig: select DMA_ENGINE when DMA_OF is selected
...
Pull thermal updates from Zhang Rui:
"Specifics:
- adds full support for 2 types of Thermal Controllers produced by
STMicroelectronics. One is a more traditional memory mapped
variant, the other is controlled solely by system configuration
registers. From Lee Jones.
- add TMU (Thermal Management Unit) support for Exynos3250 Soc.
From Chanwoo Choi.
- add critical and passive trip point support for int3403 thermal
driver. From Srinivas Pandruvada.
- a couple of small fixes/cleanups from Javi Merino, and Geert
Uytterhoeven"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: document struct thermal_zone_device and thermal_governor
thermal: cpu_cooling: fix typo highjack -> hijack
thermal: rcar: Document SoC-specific bindings
thermal: samsung: Add TMU support for Exynos3250 SoC
thermal: exynos: fix ordering in exynos_tmu_remove()
thermal: allow building dove_thermal with mvebu
thermal: sti: Add support for ST's Memory Mapped based Thermal controller
thermal: sti: Add support for ST's System Config Register based Thermal controller
thermal: sti: Introduce ST Thermal core code
thermal: sti: Supply Device Tree documentation
Thermal: int3403: Add CRT and PSV trip
Almost all SoCs use one slot per host controller.
(Even if controller can support the multiple slot, Recommend to use one slot per host controller.)
Don't use the slot-node and deprecate the "supports-highspeed" property.
Instead, use the cap-mmc/sd-highspeed.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Tushar Behera <trblinux@gmail.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull i2c updates from Wolfram Sang:
"Highlights:
- class based instantiation finally dropped for most embedded drivers
bringing boot up performance gains
- removed two drivers (one outdated, one a duplicate)
- ACPI has now operation region support (thanks to Lan Tianyu)
- the i2c-stub driver got overhauled and gained new features to
become more useful when writing i2c client drivers (thanks to
Guenter Roeck and Jean Delvare)
The rest is driver bugfixes, added bindings/ids, cleanups..."
* 'i2c/for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (43 commits)
i2c: mpc: delete unneeded test before of_node_put
i2c: rk3x: fix interrupt handling issue
i2c: imx: Fix format warning for dev_dbg
i2c: qup: disable clks and return instead of just returning error
i2c: exynos5: always enable HSI2C
i2c: designware: add new bindings
i2c: gpio: Drop dead code in i2c_gpio_remove
i2c: pca954x: put the mux to disconnected state after resume
i2c: st: Update i2c timings
drivers/i2c/busses: use correct type for dma_map/unmap
i2c: i2c-st: Use %pa to print 'resource_size_t' type
i2c: s3c2410: resume the I2C controller earlier
i2c: stub: Avoid an array overrun on I2C block transfers
i2c: i801: Add device ID for Intel Wildcat Point PCH
i2c: i801: Fix the alignment of the device table
i2c: stub: Add support for banked register ranges
i2c: stub: Remember the number of emulated chips
i2c: stub: Add support for SMBus block commands
i2c: efm32: correct namespacing of location property
i2c: exynos5: remove extra line and fix an assignment
...
Pull MTD updates from Brian Norris:
"AMD-compatible CFI driver:
- Support OTP programming for Micron M29EW family
- Increase buffer write timeout, according to detected flash
parameter info
NAND
- Add helpers for retrieving ONFI timing modes
- GPMI: provide option to disable bad block marker swapping (required
for Ka-On electronics platforms)
SPI NOR
- EON EN25QH128 support
- Support new Flag Status Register (FSR) on a few Micron flash
Common
- New sysfs entries for bad block and ECC stats
And a few miscellaneous refactorings, cleanups, and driver
improvements"
* tag 'for-linus-20140808' of git://git.infradead.org/linux-mtd: (31 commits)
mtd: gpmi: make blockmark swapping optional
mtd: gpmi: remove line breaks from error messages and improve wording
mtd: gpmi: remove useless (void *) type casts and spaces between type casts and variables
mtd: atmel_nand: NFC: support multiple interrupt handling
mtd: atmel_nand: implement the nfc_device_ready() by checking the R/B bit
mtd: atmel_nand: add NFC status error check
mtd: atmel_nand: make ecc parameters same as definition
mtd: nand: add ONFI timing mode to nand_timings converter
mtd: nand: define struct nand_timings
mtd: cfi_cmdset_0002: fix do_write_buffer() timeout error
mtd: denali: use 8 bytes for READID command
mtd/ftl: fix the double free of the buffers allocated in build_maps()
mtd: phram: Fix whitespace issues
mtd: spi-nor: add support for EON EN25QH128
mtd: cfi_cmdset_0002: Add support for locking OTP memory
mtd: cfi_cmdset_0002: Add support for writing OTP memory
mtd: cfi_cmdset_0002: Invalidate cache after entering/exiting OTP memory
mtd: cfi_cmdset_0002: Add support for reading OTP
mtd: spi-nor: add support for flag status register on Micron chips
mtd: Account for BBT blocks when a partition is being allocated
...
Pull fbdev updates from Tomi Valkeinen:
- much better HDMI infoframe support for OMAP
- Cirrus Logic CLPS711X framebuffer driver
- DT support for PL11x CLCD driver
- various small fixes
* tag 'fbdev-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (35 commits)
OMAPDSS: DSI: fix depopulating dsi peripherals
video: hyperv: hyperv_fb: refresh the VM screen by force on VM panic
video: ARM CLCD: Fix DT-related build problems
drivers: video: fbdev: atmel_lcdfb.c: Add ability to inverted backlight PWM.
video: ARM CLCD: Add DT support
drm/omap: Add infoframe & dvi/hdmi mode support
OMAPDSS: HDMI: remove the unused code
OMAPDSS: HDMI5: add support to set infoframe & HDMI mode
OMAPDSS: HDMI4: add support to set infoframe & HDMI mode
OMAPDSS: HDMI: add infoframe and hdmi_dvi_mode fields
OMAPDSS: add hdmi ops to hdmi-connector and tpd12s015
OMAPDSS: add hdmi ops to hdmi_ops and omap_dss_driver
OMAPDSS: HDMI: remove custom avi infoframe
OMAPDSS: HDMI5: use common AVI infoframe support
OMAPDSS: HDMI4: use common AVI infoframe support
OMAPDSS: Kconfig: select HDMI
OMAPDSS: HDMI: fix name conflict
OMAPDSS: DISPC: clean up dispc_mgr_timings_ok
OMAPDSS: DISPC: reject interlace for lcd out
OMAPDSS: DISPC: fix debugfs reg dump
...
Pull pwm changes from Thierry Reding:
"The set of changes for this merge window contains two new drivers: one
for Rockchip SoCs and another for STMicroelectronics STiH4xx SoCs.
The remainder of the changes are the usual small cleanups such as
removing redundant OOM messages, signalling that a PWM chip's
operations can sleep and removing an unneeded dependency"
* tag 'pwm/for-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: rockchip: Added to support for RK3288 SoC
pwm: rockchip: document RK3288 SoC compatible
pwm: sti: Remove PWM period table
pwm: sti: Sync between enable/disable calls
pwm: sti: Ensure same period values for all channels
pwm: sti: Fix PWM prescaler handling
pwm: sti: Supply Device Tree binding documentation for ST's PWM IP
pwm: sti: Add new driver for ST's PWM IP
pwm: imx: set can_sleep flag for imx_pwm
pwm: lpss: remove dependency on clk framework
pwm: pwm-tipwmss: remove unnecessary OOM messages
pwm: rockchip: document device tree bindings
pwm: add Rockchip SoC PWM support
Pull GPIO update from Linus Walleij:
"This is the bulk of GPIO changes for the v3.17 development cycle, and
this time we got a lot of action going on and it will continue:
- The core GPIO library implementation has been split up in three
different files:
- gpiolib.c for the latest and greatest and shiny GPIO library code
using GPIO descriptors only
- gpiolib-legacy.c for the old integer number space API that we are
phasing out gradually
- gpiolib-sysfs.c for the sysfs interface that we are not entirely
happy with, but has to live on for ABI compatibility
- Add a flags argument to *gpiod_get* functions, with some
backward-compatibility macros to ease transitions. We should have
had the flags there from the beginning it seems, now we need to
clean up the mess. There is a plan on how to move forward here
devised by Alexandre Courbot and Mark Brown
- Split off a special <linux/gpio/machine.h> header for the board
gpio table registration, as per example from the regulator
subsystem
- Start to kill off the return value from gpiochip_remove() by
removing the __must_check attribute and removing all checks inside
the drivers/gpio directory. The rationale is: well what were we
supposed to do if there is an error code? Not much: print an error
message. And gpiolib already does that. So make this function
return void eventually
- Some cleanups of hairy gpiolib code, make some functions not to be
used outside the library private and make sure they are not
exported, remove gpiod_lock/unlock_as_irq() as the existing
function is for driver-internal use and fine as it is, delete
gpio_ensure_requested() as it is not meaningful anymore
- Support the GPIOF_ACTIVE_LOW flag from gpio_request_one() function
calls, which is logical since this is already supported when
referencing GPIOs from e.g. device trees
- Switch STMPE, intel-mid, lynxpoint and ACPI (!) to use the gpiolib
irqchip helpers cutting down on GPIO irqchip boilerplate a bit more
- New driver for the Zynq GPIO block
- The usual incremental improvements around a bunch of drivers
- Janitorial syntactic and semantic cleanups by Jingoo Han, and
Rickard Strandqvist especially"
* tag 'gpio-v3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (37 commits)
MAINTAINERS: update GPIO include files
gpio: add missing includes in machine.h
gpio: add flags argument to gpiod_get*() functions
MAINTAINERS: Update Samsung pin control entry
gpio / ACPI: Move event handling registration to gpiolib irqchip helpers
gpio: lynxpoint: Convert to use gpiolib irqchip
gpio: split gpiod board registration into machine header
gpio: remove gpio_ensure_requested()
gpio: remove useless check in gpiolib_sysfs_init()
gpiolib: Export gpiochip_request_own_desc and gpiochip_free_own_desc
gpio: move gpio_ensure_requested() into legacy C file
gpio: remove gpiod_lock/unlock_as_irq()
gpio: make gpiochip_get_desc() gpiolib-private
gpio: simplify gpiochip_export()
gpio: remove export of private of_get_named_gpio_flags()
gpio: Add support for GPIOF_ACTIVE_LOW to gpio_request_one functions
gpio: zynq: Clear pending interrupt when enabling a IRQ
gpio: drop retval check enforcing from gpiochip_remove()
gpio: remove all usage of gpio_remove retval in driver/gpio
devicetree: Add Zynq GPIO devicetree bindings documentation
...
Pull input updates from Dmitry Torokhov:
- big update to Wacom driver by Benjamin Tissoires, converting it to
HID infrastructure and unifying USB and Bluetooth models
- large update to ALPS driver by Hans de Goede, which adds support for
newer touchpad models as well as cleans up and restructures the code
- more changes to Atmel MXT driver, including device tree support
- new driver for iPaq x3xxx touchscreen
- driver for serial Wacom tablets
- driver for Microchip's CAP1106
- assorted cleanups and improvements to existing drover and input core
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (93 commits)
Input: wacom - update the ABI doc according to latest changes
Input: wacom - only register once the MODULE_* macros
Input: HID - remove hid-wacom Bluetooth driver
Input: wacom - add copyright note and bump version to 2.0
Input: wacom - remove passing id for wacom_set_report
Input: wacom - check for bluetooth protocol while setting OLEDs
Input: wacom - handle Intuos 4 BT in wacom.ko
Input: wacom - handle Graphire BT tablets in wacom.ko
Input: wacom - prepare the driver to include BT devices
Input: hyperv-keyboard - register as a wakeup source
Input: imx_keypad - remove ifdef round PM methods
Input: jornada720_ts - get rid of space indentation and use tab
Input: jornada720_ts - switch to using managed resources
Input: alps - Rushmore and v7 resolution support
Input: mcs5000_ts - remove ifdef around power management methods
Input: mcs5000_ts - protect PM functions with CONFIG_PM_SLEEP
Input: ads7846 - release resources on failure for clean exit
Input: wacom - add support for 0x12C ISDv4 sensor
Input: atmel_mxt_ts - use deep sleep mode when stopped
ARM: dts: am437x-gp-evm: Update binding for touchscreen size
...
