We found a set but not used variable 'ring_cons' in mlx4_en_xmit(), it will
cause a warning when build the kernel. And after checking the commit record
of this function, we found that it was introduced by a previous patch.
So, We delete this redundant assignment code.
Fixes: 488a9b48e3 ("net/mlx4_en: Wake TX queues only when there's enough room")
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LAN8814 is a low-power, quad-port triple-speed (10BASE-T/100BASETX/1000BASE-T)
Ethernet physical layer transceiver (PHY). It supports transmission and
reception of data on standard CAT-5, as well as CAT-5e and CAT-6, unshielded
twisted pair (UTP) cables.
LAN8814 supports industry-standard QSGMII (Quad Serial Gigabit Media
Independent Interface) and Q-USGMII (Quad Universal Serial Gigabit Media
Independent Interface) providing chip-to-chip connection to four Gigabit
Ethernet MACs using a single serialized link (differential pair) in each
direction.
The LAN8814 SKU supports high-accuracy timestamping functions to
support IEEE-1588 solutions using Microchip Ethernet switches, as well as
customer solutions based on SoCs and FPGAs.
The LAN8804 SKU has same features as that of LAN8814 SKU except that it does
not support 1588, SyncE, or Q-USGMII with PCH/MCH.
This adds support for 10BASE-T, 100BASE-TX, and 1000BASE-T,
QSGMII link with the MAC.
Signed-off-by: Divya Koppera<divya.koppera@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than doing request_irq and then disabling the irq immediately, it
should be safer to use IRQ_NOAUTOEN flag for the irq. It removes any gap
between request_irq() and disable_irq().
Cc: Salil Mehta <salil.mehta@huawei.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TI J721E (CPSW9g) ALE version is similar, in general, to Sitara AM3/4/5
CPSW ALE, but has more extended functions and different ALE VLAN entry
format.
This patch adds support for for multi port TI J721E (CPSW9g) ALE variant.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ALE VLAN entries are too much differ between different TI CPSW ALE
versions. So, handling them using flags, defines and get/set functions
became over-complicated.
This patch introduces tables to describe the ALE VLAN entries fields, which
are different between TI CPSW ALE versions, and new get/set access
functions. It also allows to detect incorrect access to not available ALL
entry fields.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AM65x ALE supports HW auto-ageing which can be enabled by programming
ageing interval in ALE_AGING_TIMER register. For this CPSW fck_clk
frequency has to be know by ALE.
This patch extends cpsw_ale_params with bus_freq field and enables ALE HW
auto ageing for AM65x CPSW2G ALE version.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hence all existing driver updated to use ALE dev_id the usage of ale dev_id
can be made mandatory and cpsw_ale_create() can be updated to use
"features" property from ALE static configuration.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patch has introduced possibility to select CPSW ALE by using
ALE dev_id identifier. Switch TI TI AM65x/J721E CPSW NUSS driver to use
dev_id.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patch has introduced possibility to select CPSW ALE by using
ALE dev_id identifier. Switch TI Keystone 2 NETCP driver to use dev_id and
perform clean up by removing "ale_entries" configuration code.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patch has introduced possibility to select CPSW ALE by using
ALE dev_id identifier. Switch TI cpsw driver to use dev_id="cpsw" and
perform clean up by removing "ale_entries" configuration code.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As existing, as newly introduced CPSW ALE versions have differences in
supported features and ALE table formats. Especially it's actual for the
recent AM65x/J721E/J7200 SoC and feature AM64x, which supports features
like: auto-aging, classifiers, Link aggregation, additional hw filtering,
etc.
Existing ALE configuration interface is not practical in terms of adding
new features and requires consumers to program a lot static parameters. Any
attempt to add new options will case endless adding and maintaining
different combination of flags and options.
Hence CPSW ALE configuration is static and fixed for SoC (or set of SoC) It
is reasonable to add support for static ALE configurations inside ALE
module. This patch adds static ALE configuration table for different ALE
versions and provides option for consumers to select required ALE
configuration by providing ALE const char *dev_id identifier.
This feature is not enabled by default until existing CPSW drivers will be
modified by follow up patches.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cpsw_ale_get_num_entries() API to return number of ALE table entries
and update existing drivers to use it.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While working on another tag_8021q driver implementation, some things
became apparent:
- It is not mandatory for a DSA driver to offload the tag_8021q VLANs by
using the VLAN table per se. For example, it can add custom TCAM rules
that simply encapsulate RX traffic, and redirect & decapsulate rules
for TX traffic. For such a driver, it makes no sense to receive the
tag_8021q configuration through the same callback as it receives the
VLAN configuration from the bridge and the 8021q modules.
- Currently, sja1105 (the only tag_8021q user) sets a
priv->expect_dsa_8021q variable to distinguish between the bridge
calling, and tag_8021q calling. That can be improved, to say the
least.
- The crosschip bridging operations are, in fact, stateful already. The
list of crosschip_links must be kept by the caller and passed to the
relevant tag_8021q functions.
So it would be nice if the tag_8021q configuration was more
self-contained. This patch attempts to do that.
Create a struct dsa_8021q_context which encapsulates a struct
dsa_switch, and has 2 function pointers for adding and deleting a VLAN.
These will replace the previous channel to the driver, which was through
the .port_vlan_add and .port_vlan_del callbacks of dsa_switch_ops.
Also put the list of crosschip_links into this dsa_8021q_context.
Drivers that don't support cross-chip bridging can simply omit to
initialize this list, as long as they dont call any cross-chip function.
The sja1105_vlan_add and sja1105_vlan_del functions are refactored into
a smaller sja1105_vlan_add_one, which now has 2 entry points:
- sja1105_vlan_add, from struct dsa_switch_ops
- sja1105_dsa_8021q_vlan_add, from the tag_8021q ops
But even this change is fairly trivial. It just reflects the fact that
for sja1105, the VLANs from these 2 channels end up in the same hardware
table. However that is not necessarily true in the general sense (and
that's the reason for making this change).
The rest of the patch is mostly plain refactoring of "ds" -> "ctx". The
dsa_8021q_context structure needs to be propagated because adding a VLAN
is now done through the ops function pointers inside of it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point in calling dsa_port_setup_8021q_tagging for each
individual port. Additionally, it will become more difficult to do that
when we'll have a context structure to tag_8021q (next patch). So
refactor this now.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves complete nic tls offload (kTLS) code from crypto
directory to drivers/net/ethernet/chelsio/inline_crypto/ch_ktls
directory. nic TLS is made a separate ULD of cxgb4.
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Necessitates an .ndo_features_check, as the EF10 datapath has several
limitations on what it can handle.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
>From the 8000 series onwards, EF10 NICs with suitable firmware are able
to perform TSO within VXLAN or NVGRE encapsulation.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the tx_queue->handle_tso function pointer, and just use
tx_queue->tso_version to decide which function to call, thus removing
an indirect call from the fast path.
Instead of passing a tso_v2 flag to efx_mcdi_tx_init(), set the desired
tx_queue->tso_version before calling it.
In efx_mcdi_tx_init(), report back failure to obtain a TSOv2 context by
setting tx_queue->tso_version to 0, which will cause the TX path to
use the GSO-based fallback.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Won't actually be exercised until we start advertising the corresponding
offload features.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the MC reports the VXLAN_NVGRE datapath capability, then these queues
can be used for checksum offload of encapsulated packets.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing yet creates inner csum TXQs; just change all references to
EFX_TXQ_TYPE_OFFLOAD to the new EFX_TXQ_TYPE_OUTER_CSUM.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it possible to have an arbitrary mapping from types to labels,
because when we add inner-csum-offload TXQs there will no longer be a
convenient nesting hierarchy of NIC types (EF10 will have inner-csum
TXQs, while Siena will have HIGHPRI).
Correct a misleading comment on efx_hard_start_xmit().
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are never modified, so constify them to allow the compiler to
place them in read-only memory. This moves about 25kB to read-only
memory as seen by the output of the size command.
Before:
text data bss dec hex filename
296203 65464 1248 362915 589a3 drivers/net/ethernet/marvell/octeontx2/af/octeontx2_af.ko
After:
text data bss dec hex filename
321003 40664 1248 362915 589a3 drivers/net/ethernet/marvell/octeontx2/af/octeontx2_af.ko
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The old_channel argument is never used, so remove it.
The function is only called from elsewhere in efx_channels.c, so make
it static and remove the declaration from the header file.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The statement above it already returns, so there is no way to get here.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
efx_init_struct already calls this, we don't need to do it again.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add flow control support. The functionality was tested on AR9331 SoC and
confirmed by iperf3 results and HW counters exported over ethtool.
Following test configurations was used:
iMX6S receiver <--- TL-SG1005D switch <---- AR9331 sender
The switch is supporting symmytric flow control:
Settings for eth0:
Supported ports: [ MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Link partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
--->> Link partner advertised pause frame use: Symmetric
Link partner advertised auto-negotiation: Yes
Link partner advertised FEC modes: Not reported
Speed: 100Mb/s
Duplex: Full
Auto-negotiation: on
Port: MII
PHYAD: 4
Transceiver: external
Link detected: yes
The iMX6S system was configured to 10Mbit, to let the switch use flow
control:
- ethtool -s eth0 speed 10
With flow control disabled on AR9331:
- ethtool -A eth0 rx off tx off
- iperf3 -u -c 172.17.0.1 -b100M -l1472 -t10
[ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams
[ 5] 0.00-10.00 sec 66.2 MBytes 55.5 Mbits/sec 0.000 ms 0/47155 (0%) sender
[ 5] 0.00-10.04 sec 11.5 MBytes 9.57 Mbits/sec 1.309 ms 38986/47146 (83%) receiver
With flow control enabled on AR9331:
- ethtool -A eth0 rx on tx on
- iperf3 -u -c 172.17.0.1 -b100M -l1472 -t10
[ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams
[ 5] 0.00-10.00 sec 15.1 MBytes 12.6 Mbits/sec 0.000 ms 0/10727 (0%) sender
[ 5] 0.00-10.05 sec 11.5 MBytes 9.57 Mbits/sec 1.371 ms 2525/10689 (24%) receiver
Similar results are get in opposite direction by introducing extra CPU
load on AR9331:
- chrt 40 dd if=/dev/zero of=/dev/null &
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "SLF_OUTWAIT" flag defined in x25_asy.h is not actually used.
It is only cleared at one place in x25_asy.c but is never read or set.
So we can remove it.
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We found the following warning when using W=1 to build kernel:
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:3634:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
int ret, coe = priv->hw->rx_csum;
When digging stmmac_get_rx_header_len(), dwmac4_get_rx_header_len() and
dwxgmac2_get_rx_header_len() return 0 only, without any error code to
report. Therefore, it's better to define get_rx_header_len() as void.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change allows the driver to report the device link speed
when the ethtool command:
ethtool <nic name>
is run.
Getting the link speed is done via a new admin queue command:
ReportLinkSpeed.
Reviewed-by: Yangchun Fu <yangchun@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes the driver better aware of the connectivity status of the
device. Based on the device's status register, the driver can call
netif_carrier_{on,off}.
Reviewed-by: Yangchun Fu <yangchun@google.com>
Signed-off-by: Patricio Noyola <patricion@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds per queue NIC stats to ethtool stats and to report-stats.
These stats are always exposed to guest whether or not the
report-stats flag is turned on.
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds functionality to report driver stats to Hypervisor.
(Users may want to turn this feature off as a matter of privacy
so a "report-stats" flag is added as an ethtool priv option.
It is also disabled by default.)
The hypervisor would trigger a stats report in case "too many"
packets dropped; the stats would be useful in debugging stuck
queues.
A "stats_report_trigger_cnt" stat is added to count the number of times
the hypervisor attempts to trigger stats report.
A timer is also added so that when report-stats is enabled, stat are
updated once every 20 seconds.
Reviewed-by: Yangchun Fu <yangchun@google.com>
Signed-off-by: Kuo Zhao <kuozhao@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo says:
====================
wireless-drivers-next patches for v5.10
First set of patches for v5.10. Most noteworthy here is ath11k getting
initial support for QCA6390 and IPQ6018 devices. But most of the
patches are cleanup: W=1 warning fixes, fallthrough keywords, DMA API
changes and tasklet API changes.
Major changes:
ath10k
* support SDIO firmware codedumps
* support station specific TID configurations
ath11k
* add support for IPQ6018
* add support for QCA6390 PCI devices
ath9k
* add support for NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 to improve PTK0
rekeying
wcn36xx
* add support for TX ack
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for v5.10. Major changes:
ath10k
* support SDIO firmware codedumps
* support station specific TID configurations
ath11k
* add support for IPQ6018
