[ Upstream commit 92d3360108f1839ca40451bad20ff67dd24a1964 ]
Add a quirk mechanism to allow specifying that active-high jack-detection
should be used on platforms where this info is not available in devicetree.
And add an entry for the Cyberbook T116 tablet to the DMI table, so that
jack-detection will work properly on this tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211002211459.110124-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 778a0cbef5fb76bf506f84938517bb77e7a1c478 ]
The setting from the cirrus,ts-inv property should be applied to the
TIP_SENSE_INV bit, as this is the one that actually affects the jack
detect block. The TS_INV bit only swaps the meaning of the PLUG and
UNPLUG interrupts and should always be 1 for the interrupts to have
the normal meaning.
Due to some misunderstanding the driver had been implemented to
configure the TS_INV bit based on the jack switch polarity. This made
the interrupts behave the correct way around, but left the jack detect
block, button detect and analogue circuits always interpreting an open
switch as unplugged.
The signal chain inside the codec is:
SENSE pin -> TIP_SENSE_INV -> TS_INV -> (invert) -> interrupts
|
v
Jack detect,
button detect and
analog control
As the TIP_SENSE_INV already performs the necessary inversion the
TS_INV bit never needs to change. It must always be 1 to yield the
expected interrupt behaviour.
Some extra confusion has arisen because of the additional invert in the
interrupt path, meaning that a value applied to the TS_INV bit produces
the opposite effect of applying it to the TIP_SENSE_INV bit. The ts-inv
property has therefore always had the opposite effect to what might be
expected (0 = inverted, 1 = not inverted). To maintain the meaning of
the ts-inv property it must be inverted when applied to TIP_SENSE_INV.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2c394ca796 ("ASoC: Add support for CS42L42 codec")
Link: https://lore.kernel.org/r/20211028140902.11786-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0306988789d9d91a18ff70bd2bf165d3ae0ef1dd ]
The driver can run without an interrupt so if devm_request_threaded_irq()
failed, the probe() just carried on. But if this was EPROBE_DEFER the
driver would continue without an interrupt instead of deferring to wait
for the interrupt to become available.
Fixes: 2c394ca796 ("ASoC: Add support for CS42L42 codec")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211015133619.4698-6-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b9b546dc00797c74bef491668ce5431ff54e1e2 ]
There is a noise issue for 8kHz sample rate on slave mode.
Compared with master mode, the difference is the DACDIV
setting, after correcting the DACDIV, the noise is gone.
There is no noise issue for 48kHz sample rate, because
the default value of DACDIV is correct for 48kHz.
So wm8960_configure_clocking() should be functional for
ADC and DAC function even if it is slave mode.
In order to be compatible for old use case, just add
condition for checking that sysclk is zero with
slave mode.
Fixes: 0e50b51aa2 ("ASoC: wm8960: Let wm8960 driver configure its bit clock and frame clock")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/1634102224-3922-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a6a723e98aa45f393e6add18f7309dfffa1b0e2 ]
There is no point in calling 'free_irq()' explicitly for
'WCD9335_IRQ_SLIMBUS' in the remove function.
The irqs are requested in 'wcd9335_setup_irqs()' using a resource managed
function (i.e. 'devm_request_threaded_irq()').
'wcd9335_setup_irqs()' requests all what is defined in the 'wcd9335_irqs'
structure.
This structure has only one entry for 'WCD9335_IRQ_SLIMBUS'.
So 'devm_request...irq()' + explicit 'free_irq()' would lead to a double
free.
Remove the unneeded 'free_irq()' from the remove function.
Fixes: 20aedafdf4 ("ASoC: wcd9335: add support to wcd9335 codec")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Message-Id: <0614d63bc00edd7e81dd367504128f3d84f72efa.1629091028.git.christophe.jaillet@wanadoo.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 772d44526e203c062171786e514373f129616278 ]
When I booted up on a board that had a slightly different codec
stuffed on it, I got this message at bootup:
rt5682 9-001a: Device with ID register 6749 is not rt5682
That's normal/expected, but what wasn't normal was the splat that I
got after:
WARNING: CPU: 7 PID: 176 at drivers/regulator/core.c:2151 _regulator_put+0x150/0x158
pc : _regulator_put+0x150/0x158
...
Call trace:
_regulator_put+0x150/0x158
regulator_bulk_free+0x48/0x70
devm_regulator_bulk_release+0x20/0x2c
release_nodes+0x1cc/0x244
devres_release_all+0x44/0x60
really_probe+0x17c/0x378
...
This is because the error paths don't turn off the regulator. Let's
fix that.
Fixes: 0ddce71c21 ("ASoC: rt5682: add rt5682 codec driver")
Fixes: 87b42abae99d ("ASoC: rt5682: Implement remove callback")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210811081751.v2.1.I4a1d9aa5d99e05aeee15c2768db600158d76cab8@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c2f2ad4f16a58879463d0979a54293f8f296d6f ]
An I2S frame starts on the falling edge of LRCLK so ASP_STP must
be 0.
At the same time, move other format settings in the same register
from cs42l42_pll_config() to cs42l42_set_dai_fmt() where you'd
expect to find them, and merge into a single write.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2c394ca796 ("ASoC: Add support for CS42L42 codec")
Link: https://lore.kernel.org/r/20210805161111.10410-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b353bbeae20e2214c9d9d88bcb2fda4ba145d83 ]
The driver was defining two ALSA controls that both change the same
register field for the wind noise filter corner frequency. The filter
response has two corners, at different frequencies, and the duplicate
controls most likely were an attempt to be able to set the value using
either of the frequencies.
However, having two controls changing the same field can be problematic
and it is unnecessary. Both frequencies are related to each other so
setting one implies exactly what the other would be.
Removing a control affects user-side code, but there is currently no
known use of the removed control so it would be best to remove it now
before it becomes a problem.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2c394ca796 ("ASoC: Add support for CS42L42 codec")
Link: https://lore.kernel.org/r/20210803160834.9005-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2c39ca6885a2ec03e5c9e7c12a4da2aa8926605a upstream.
The tlv320aic31xx driver relies on regcache_sync() to restore the register
contents after going to _BIAS_OFF, for example during system suspend. This
does not work for the jack detection configuration since that is configured
via the same register that status is read back from so the register is
volatile and not cached. This can also cause issues during init if the jack
detection ends up getting set up before the CODEC is initially brought out
of _BIAS_OFF, we will reset the CODEC and resync the cache as part of that
process.
Fix this by explicitly reapplying the jack detection configuration after
resyncing the register cache during power on.
This issue was found by an engineer working off-list on a product
kernel, I just wrote up the upstream fix.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210723180200.25105-1-broonie@kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9cf76a72af6ab81030dea6481b1d7bdd814fbdaf ]
These are backwards from Table 7-71 of the TLV320AIC3100 spec [1].
This was broken in 12eb4d66ba when BCLK_MASTER and WCLK_MASTER
were converted from 0x08 and 0x04 to BIT(2) and BIT(3), respectively.
-#define AIC31XX_BCLK_MASTER 0x08
-#define AIC31XX_WCLK_MASTER 0x04
+#define AIC31XX_BCLK_MASTER BIT(2)
+#define AIC31XX_WCLK_MASTER BIT(3)
Probably just a typo since the defines were not listed in bit order.
[1] https://www.ti.com/lit/gpn/tlv320aic3100
Signed-off-by: Kyle Russell <bkylerussell@gmail.com>
Link: https://lore.kernel.org/r/20210622010941.241386-1-bkylerussell@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c71f78a662611fe2c67f3155da19b0eff0f29762 ]
The ALC5631 does not like multi-write accesses, avoid them. This fixes:
rt5631 4-001a: Unable to sync registers 0x3a-0x3c. -121
errors on resume from suspend (and all registers after the registers in
the error not being synced).
Inspired by commit 2d30e9494f ("ASoC: rt5651: Fix regcache sync errors
on resume") from Hans de Geode, which fixed the same errors on ALC5651.
Signed-off-by: Maxim Schwalm <maxim.schwalm@gmail.com>
Link: https://lore.kernel.org/r/20210712005011.28536-1-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd6fb8ff2210f74b056bf9234d0605e8c26a8ac0 ]
When wm_coeff_tlv_get was updated it was accidentally switch to the _raw
version of the helper causing it to ignore the current DSP state it
should be checking. Switch the code back to the correct helper so that
users can't read the controls when they arn't available.
Fixes: 73ecf1a673 ("ASoC: wm_adsp: Correct cache handling of new kernel control API")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210626155941.12251-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 867f8d18df4f5ccd6c2daf4441a6adeca0b9725b ]
This patch will be the workaround to fix getting the wrong device ID on the rare chance.
It seems like something unstable when the system resumes. e.g. the bus clock
This patch tries to read the device ID to check several times.
After the test, the driver will get the correct device ID the second time.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20210111092740.9128-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf881170311ea74ff30c3be0be8fb097132ce696 ]
The intent of the status check on resume was to verify if a SoundWire
peripheral reported ATTACHED before waiting for the initialization to
complete. This is required to avoid timeouts that will happen with
'ghost' devices that are exposed in the platform firmware but are not
populated in hardware.
Unfortunately we used 'hw_init' instead of 'first_hw_init'. Due to
another error, the resume operation never timed out, but the volume
settings were not properly restored.
This patch renames the status flag to 'first_hw_init' for consistency
with other drivers.
BugLink: https://github.com/thesofproject/linux/issues/2637
Fixes: 56a5b7910e ('ASoC: codecs: max98373: add SoundWire support')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Link: https://lore.kernel.org/r/20210607222239.582139-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47bcb1c7108363418cd578283333d72e310dfeaa ]
We cancel the work queues, and reset the device on shutdown, but the irq
isn't disabled so the work queues could be queued again. Let's disable
the irq during shutdown so that we don't have to worry about this device
trying to do anything anymore. This fixes a problem seen where the i2c
bus is shutdown at reboot but this device irq still comes in and tries
to make another i2c transaction when the bus doesn't work.
Cc: Jairaj Arava <jairaj.arava@intel.com>
Cc: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@intel.com>
Cc: Shuming Fan <shumingf@realtek.com>
Cc: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Fixes: 45a2702ce109 ("ASoC: rt5682: Fix panic in rt5682_jack_detect_handler happening during system shutdown")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210508075151.1626903-1-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6308c44ed6eeadf65c0a7ba68d609773ed860fbb ]
The power of "LDO2", "MICBIAS1" and "Mic Det Power" were powered off after
the DAPM widgets were added, and these powers were set by the JD settings
"RT5659_JD_HDA_HEADER" in the probe function. In the codec probe function,
these powers were ignored to prevent them controlled by DAPM.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Jack Yu <jack.yu@realtek.com>
Message-Id: <15fced51977b458798ca4eebf03dafb9@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0fad605fb0bdc00d8ad78696300ff2fbdee6e048 ]
cs42l42 does not support standard burst transfers so the use_single_read
and use_single_write flags must be set in the regmap config.
Because of this bug, the patch:
commit 0a0eb567e1d4 ("ASoC: cs42l42: Minor error paths fixups")
broke cs42l42 probe() because without the use_single_* flags it causes
regmap to issue a burst read.
However, the missing use_single_* could cause problems anyway because the
regmap cache can attempt burst transfers if these flags are not set.
Fixes: 2c394ca796 ("ASoC: Add support for CS42L42 codec")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210511132855.27159-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2da441a6491d93eff8ffff523837fd621dc80389 ]
cs43130_probe() does not do any valid error checking of things it
initializes, OR what it does, it does not unwind properly if there are
errors.
Fix this up by moving the sysfs files to an attribute group so the
driver core will correctly add/remove them all at once and handle errors
with them, and correctly check for creating a new workqueue and
unwinding if that fails.
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-58-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fdda0dd2686ecd1f2e616c9e0366ea71b40c485d ]
This reverts commit a2be42f18d.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original patch here is not correct, sysfs files that were created
are not unwound.
Cc: Kangjie Lu <kjlu@umn.edu>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-57-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99067c07e8d877035f6249d194a317c78b7d052d ]
The call sequence in wm8960_configure_clocking is
ret = wm8960_configure_sysclk();
if (ret >= 0)
goto configure_clock;
....
ret = wm8960_configure_pll();
configure_clock:
...
wm8960_configure_sysclk is called before wm8960_configure_pll, as
there is bitclk relax on both functions, so wm8960_configure_sysclk
always return success, then wm8960_configure_pll() never be called.
With this case:
aplay -Dhw:0,0 -d 5 -r 48000 -f S24_LE -c 2 audio48k24b2c.wav
the required bitclk is 48000 * 24 * 2 = 2304000, bitclk got from
wm8960_configure_sysclk is 3072000, but if go to wm8960_configure_pll.
it can get correct bitclk 2304000.
So bitclk relax condition should be removed in wm8960_configure_sysclk,
then wm8960_configure_pll can be called, and there is also bitclk relax
function in wm8960_configure_pll.
Fixes: 3c01b9ee2a ("ASoC: codec: wm8960: Relax bit clock computation")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/1614740862-30196-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
