[ Upstream commit e59bf547a7dd366f93bfebb7487959580ca6c0ec ]
There's a special branch in the set_tdm_slot op for the case of nslots
being 1, but:
(1) That branch can never work (there's a check for tx_mask being
non-zero, later there's another check for it *being* zero; one or
the other always throws -EINVAL).
(2) The intention of the branch seems to be what the general other
branch reduces to in case of nslots being 1.
For those reasons remove the 'nslots being 1' special case.
Fixes: 1a476abc72 ("tas2770: add tas2770 smart PA kernel driver")
Suggested-by: Jos Dehaes <jos.dehaes@gmail.com>
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20221027095800.16094-1-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a0342ede303fc420f3a388e1ae82da3ae8ff6bd ]
On probe of the ASoC component, the device is reset but the regcache is
retained. This means the regcache gets out of sync if the codec is
rebound to a sound card for a second time. Fix it by reinitializing the
regcache to defaults after the device is reset.
Fixes: b0bcbe6157 ("ASoC: tas2770: Fix calling reset in probe")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220919173453.84292-1-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1e5907bcb3a3b569be0a03ebe668bba2ed320a50 upstream.
Because the PWR_CTRL field is modeled as the power state of the DAC
widget, and at the same time it is used to implement mute/unmute, we
need some additional book-keeping to have the right end result no matter
the sequence of calls. Without this fix, one can mute an ongoing stream
by toggling a speaker pin control.
Fixes: 1a476abc72 ("tas2770: add tas2770 smart PA kernel driver")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220808141246.5749-5-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 482c23fbc7e9bf5a7a74defd0735d5346215db58 upstream.
The driver is setting the PWR_CTRL field in both the set_bias_level
callback and on DAPM events of the DAC widget (and also in the
mute_stream method). Drop the set_bias_level callback altogether as the
power setting it does is in conflict with the other code paths.
Fixes: 1a476abc72 ("tas2770: add tas2770 smart PA kernel driver")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220808141246.5749-4-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the code to support the asi-format binding property. The code
does nothing except read the property and set a variable. No additional
action is taken except to reset the variable. The property is supposed
to set the rising or falling RX edge detection of the SBCLK but this
edge detection is done by checking the DAI_FMT_INV_MASK.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200923132600.10652-5-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Refactor the tas2770_set_samplerate to simplify the code and access the
I2C bus only once per rate request. The ramp rate and sample rate bits
are contained in the same register so a single call to the
snd_soc_update_bits function is all that is needed
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200918190548.12598-9-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the unbalanced call to the pm_runtime_disable when removing the
module. pm_runtime_enable is not called nor is the pm_runtime setup in
the code. Remove the i2c_remove function and the pm_runtime_disable.
Fixes: 1a476abc72 ("tas2770: add tas2770 smart PA kernel driver")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200918190548.12598-5-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_update_bits returns a 1 when the bit was successfully updated,
returns a 0 is no update was needed and a negative if the call failed.
The code is currently failing the case of a successful update by just
checking for a non-zero number. Modify these checks and return the error
code only if there is a negative.
Fixes: 1a476abc72 ("tas2770: add tas2770 smart PA kernel driver")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200918190548.12598-7-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The devicetree binding indicates that the ti,asi-format, ti,imon-slot-no
and ti,vmon-slot-no are not required but the driver requires them or it
fails to probe. Honor the binding and allow these entries to be optional
and set the corresponding values to the default values for each as defined
in the data sheet.
Fixes: 1a476abc72 ("tas2770: add tas2770 smart PA kernel driver")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200918190548.12598-4-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
tas2770_reset is called during i2c probe. The reset calls the
snd_soc_component_write which depends on the tas2770->component being
available. The component pointer is not set until codec_probe so move
the reset to the codec_probe after the pointer is set.
Fixes: 1a476abc72 ("tas2770: add tas2770 smart PA kernel driver")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200918190548.12598-1-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200719153822.59788-1-grandmaster@al2klimov.de
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_dai_digital_mute() is internally using both
mute_stream() (1) or digital_mute() (2), but the difference between
these 2 are only handling direction.
We can merge digital_mute() into mute_stream
int snd_soc_dai_digital_mute(xxx, int direction)
{
...
else if (dai->driver->ops->mute_stream)
(1) return dai->driver->ops->mute_stream(xxx, direction);
else if (direction == SNDRV_PCM_STREAM_PLAYBACK &&
dai->driver->ops->digital_mute)
(2) return dai->driver->ops->digital_mute(xxx);
...
}
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/873661xxhu.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
According the documentation for snd_soc_update_bits the API
will return a 1 if the update was successful with a value change,
a 0 if the update was successful with no value change or a negative
if the command just failed.
So the value of return in the driver needs to be checked for being less
then 0 or the caller may indicate failure when the value actually
changed.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20191007171157.17813-1-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If GPIOLIB is not set, building fails:
sound/soc/codecs/tas2770.c: In function tas2770_reset:
sound/soc/codecs/tas2770.c:38:3: error: implicit declaration of function gpiod_set_value_cansleep; did you mean gpio_set_value_cansleep? [-Werror=implicit-function-declaration]
gpiod_set_value_cansleep(tas2770->reset_gpio, 0);
^~~~~~~~~~~~~~~~~~~~~~~~
gpio_set_value_cansleep
sound/soc/codecs/tas2770.c: In function tas2770_i2c_probe:
sound/soc/codecs/tas2770.c:749:24: error: implicit declaration of function devm_gpiod_get_optional; did you mean devm_regulator_get_optional? [-Werror=implicit-function-declaration]
tas2770->reset_gpio = devm_gpiod_get_optional(tas2770->dev,
^~~~~~~~~~~~~~~~~~~~~~~
devm_regulator_get_optional
sound/soc/codecs/tas2770.c:751:13: error: GPIOD_OUT_HIGH undeclared (first use in this function); did you mean GPIOF_INIT_HIGH?
GPIOD_OUT_HIGH);
^~~~~~~~~~~~~~
GPIOF_INIT_HIGH
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 1a476abc72 ("tas2770: add tas2770 smart PA kernel driver")
Suggested-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20191006104631.60608-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
