commit 0fddf9ad06fd9f439f137139861556671673e31c upstream.
06781a5026350 Fixes the calculation of the DEVICE_BUSY_TIMEOUT register
value from busy_timeout_cycles. busy_timeout_cycles is calculated wrong
though: It is calculated based on the maximum page read time, but the
timeout is also used for page write and block erase operations which
require orders of magnitude bigger timeouts.
Fix this by calculating busy_timeout_cycles from the maximum of
tBERS_max and tPROG_max.
This is for now the easiest and most obvious way to fix the driver.
There's room for improvements though: The NAND_OP_WAITRDY_INSTR tells us
the desired timeout for the current operation, so we could program the
timeout dynamically for each operation instead of setting a fixed
timeout. Also we could wire up the interrupt handler to actually detect
and forward timeouts occurred when waiting for the chip being ready.
As a sidenote I verified that the change in 06781a5026350 is really
correct. I wired up the interrupt handler in my tree and measured the
time between starting the operation and the timeout interrupt handler
coming in. The time increases 41us with each step in the timeout
register which corresponds to 4096 clock cycles with the 99MHz clock
that I have.
Fixes: 06781a5026350 ("mtd: rawnand: gpmi: Fix setting busy timeout setting")
Fixes: b120612206 ("mtd: rawniand: gpmi: use core timings instead of an empirical derivation")
Cc: stable@vger.kernel.org
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Han Xu <han.xu@nxp.com>
Tested-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3e4ad3212cf22687410b1e8f4e68feec50646113 ]
The meson_nfc_ecc_correct() function accidentally does a right shift
instead of a left shift so it only works for BIT(0). Also use
BIT_ULL() because "correct_bitmap" is a u64 and we want to avoid
shift wrapping bugs.
Fixes: 8fae856c53 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/YuI2zF1hP65+LE7r@kili
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 049e43b9fd8fd2966940485da163d67e96ee3fea ]
Commit f6424c22aa ("mtd: rawnand: fsl_elbc: Make SW ECC work") added
support for specifying ECC mode via DTS and skipping autodetection.
But it broke explicit specification of HW ECC mode in DTS as correct
settings for HW ECC mode are applied only when NONE mode or nothing was
specified in DTS file.
Also it started aliasing NONE mode to be same as when ECC mode was not
specified and disallowed usage of ON_DIE mode.
Fix all these issues. Use autodetection of ECC mode only in case when mode
was really not specified in DTS file by checking that ecc value is invalid.
Set HW ECC settings either when HW ECC was specified in DTS or it was
autodetected. And do not fail when ON_DIE mode is set.
Fixes: f6424c22aa ("mtd: rawnand: fsl_elbc: Make SW ECC work")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220707184328.3845-1-pali@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fc9e18f9e987ad46722dad53adab1c12148c213c upstream.
Under the following conditions:
* after rounding up by 4 the number of bytes to transfer (this is
related to the controller's internal constraints),
* if this (rounded) amount of data is situated beyond the end of the
device,
* and only in NV-DDR mode,
the Arasan NAND controller timeouts.
This currently can happen in a particular helper used when picking
software ECC algorithms. Let's prevent this situation by refusing to use
the NV-DDR interface with software engines.
Fixes: 4edde6031458 ("mtd: rawnand: arasan: Support NV-DDR interface")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211008163640.1753821-1-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e16eceea863b417fd328588b1be1a79de0bc937f ]
According to the Arasan NAND controller spec, the flash clock rate for SDR
must be <= 100 MHz, while for NV-DDR it must be the same as the rate of the
CLK line for the mode. The driver previously always set 100 MHz for NV-DDR,
which would result in incorrect behavior for NV-DDR modes 0-4.
The appropriate clock rate can be calculated from the NV-DDR timing
parameters as 1/tCK, or for rates measured in picoseconds,
10^12 / nand_nvddr_timings->tCK_min.
Fixes: 197b88fecc ("mtd: rawnand: arasan: Add new Arasan NAND controller")
CC: stable@vger.kernel.org # 5.8+
Signed-off-by: Olga Kitaina <okitain@gmail.com>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220628154824.12222-3-amit.kumar-mahapatra@xilinx.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec0da06337751b18f6dee06b6526e0f0d6e80369 ]
When meson_nfc_nand_chip_cleanup() is called, it will call:
meson_nfc_free_buffer(&meson_chip->nand);
nand_cleanup(&meson_chip->nand);
nand_cleanup() in turn will call nand_detach() which calls the
.detach_chip() which is here meson_nand_detach_chip().
meson_nand_detach_chip() already calls meson_nfc_free_buffer(), so we
could double free some memory.
Fix it by removing the unneeded explicit call to meson_nfc_free_buffer().
Fixes: 8fae856c53 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/ec15c358b8063f7c50ff4cd628cf0d2e14e43f49.1653064877.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7499bfeedb47efc1ee4dc793b92c610d46e6d6a6 upstream.
In current implementation the Arasan NAND driver is updating the
system clock(i.e., anand->clk) in accordance to the timing modes
(i.e., SDR or NVDDR). But as per the Arasan NAND controller spec the
flash clock or the NAND bus clock(i.e., nfc->bus_clk), need to be
updated instead. This patch keeps the system clock unchanged and updates
the NAND bus clock as per the timing modes.
Fixes: 197b88fecc ("mtd: rawnand: arasan: Add new Arasan NAND controller")
CC: stable@vger.kernel.org # 5.8+
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220628154824.12222-2-amit.kumar-mahapatra@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 06781a5026350cde699d2d10c9914a25c1524f45 upstream.
The DEVICE_BUSY_TIMEOUT value is described in the Reference Manual as:
| Timeout waiting for NAND Ready/Busy or ATA IRQ. Used in WAIT_FOR_READY
| mode. This value is the number of GPMI_CLK cycles multiplied by 4096.
So instead of multiplying the value in cycles with 4096, we have to
divide it by that value. Use DIV_ROUND_UP to make sure we are on the
safe side, especially when the calculated value in cycles is smaller
than 4096 as typically the case.
This bug likely never triggered because any timeout != 0 usually will
do. In my case the busy timeout in cycles was originally calculated as
2408, which multiplied with 4096 is 0x968000. The lower 16 bits were
taken for the 16 bit wide register field, so the register value was
0x8000. With 2970bf5a32f0 ("mtd: rawnand: gpmi: fix controller timings
setting") however the value in cycles became 2384, which multiplied
with 4096 is 0x950000. The lower 16 bit are 0x0 now resulting in an
intermediate timeout when reading from NAND.
Fixes: b120612206 ("mtd: rawnand: gpmi: use core timings instead of an empirical derivation")
Cc: stable@vger.kernel.org
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220614083138.3455683-1-s.hauer@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a28ed09dafee20da51eb26452950839633afd824 ]
It will cause null-ptr-deref when using 'res', if platform_get_resource()
returns NULL, so move using 'res' after devm_ioremap_resource() that
will check it to avoid null-ptr-deref.
And use devm_platform_get_and_ioremap_resource() to simplify code.
Fixes: ec4ba01e89 ("mtd: rawnand: Add new Cadence NAND driver to MTD subsystem")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220426084913.4021868-1-yangyingliang@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fe4e0d3cbfe90152137963cc024ecb63db6e8e6 ]
According to the datasheet, mt7622 only has 5 ECC capabilities instead
of 7, and the decoding error register is arranged as follows:
+------+---------+---------+---------+---------+
| Bits | 19:15 | 14:10 | 9:5 | 4:0 |
+------+---------+---------+---------+---------+
| Name | ERRNUM3 | ERRNUM2 | ERRNUM1 | ERRNUM0 |
+------+---------+---------+---------+---------+
This means err_mask should be 0x1f instead of 0x3f and the number of
bits shifted in mtk_ecc_get_stats should be 5 instead of 8.
This commit introduces err_shift for the difference in this register
and fix other existing parameters.
Public MT7622 reference manual can be found on [0] and the info this
commit is based on is from page 656 and page 660.
[0]: https://wiki.banana-pi.org/Banana_Pi_BPI-R64#Documents
Fixes: 98dea8d719 ("mtd: nand: mtk: Support MT7622 NAND flash controller.")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220402160315.919094-1-gch981213@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2970bf5a32f079e1e9197411db4fe9faccb1503a ]
Set the controller registers according to the real clock rate. The
controller registers configuration (setup, hold, timeout, ... cycles)
depends on the clock rate of the GPMI. Using the real rate instead of
the ideal one, avoids that this inaccuracy (required_rate - real_rate)
affects the registers setting.
This patch has been tested on two custom boards with i.MX28 and i.MX6
SOCs:
- i.MX28:
required rate 100MHz, real rate 99.3MHz
- i.MX6
required rate 100MHz, real rate 99MHz
Fixes: b120612206 ("mtd: rawnand: gpmi: use core timings instead of an empirical derivation")
Co-developed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220118095434.35081-3-dario.binacchi@amarulasolutions.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 36415a7964711822e63695ea67fede63979054d9 upstream.
The brcmnand driver contains a bug in which if a page (example 2k byte)
is read from the parallel/ONFI NAND and within that page a subpage (512
byte) has correctable errors which is followed by a subpage with
uncorrectable errors, the page read will return the wrong status of
correctable (as opposed to the actual status of uncorrectable.)
The bug is in function brcmnand_read_by_pio where there is a check for
uncorrectable bits which will be preempted if a previous status for
correctable bits is detected.
The fix is to stop checking for bad bits only if we already have a bad
bits status.
Fixes: 27c5b17cd1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: david regan <dregan@mail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/trinity-478e0c09-9134-40e8-8f8c-31c371225eda-1643237024774@3c-app-mailcom-lxa02
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c23b3f965bc9ee696bf2ed4bdc54d339dd9a455 upstream.
Interacting with a NAND chip on an IPQ6018 I found that the qcomsmem NAND
partition parser was returning -EPROBE_DEFER waiting for the main smem
driver to load.
This caused the board to reset. Playing about with the probe() function
shows that the problem lies in the core clock being switched off before the
nandc_unalloc() routine has completed.
If we look at how qcom_nandc_remove() tears down allocated resources we see
the expected order is
qcom_nandc_unalloc(nandc);
clk_disable_unprepare(nandc->aon_clk);
clk_disable_unprepare(nandc->core_clk);
dma_unmap_resource(&pdev->dev, nandc->base_dma, resource_size(res),
DMA_BIDIRECTIONAL, 0);
Tweaking probe() to both bring up and tear-down in that order removes the
reset if we end up deferring elsewhere.
Fixes: c76b78d8ec ("mtd: nand: Qualcomm NAND controller driver")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220103030316.58301-2-bryan.odonoghue@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c9d709965385de5a99f84b14bd5860e1541729e upstream.
The function nand_davinci_read_page_hwecc_oob_first() first reads the
OOB data, extracts the ECC information, programs the ECC hardware before
reading the actual data in a loop.
Right after the OOB data was read, it called nand_read_page_op() to
reset the read cursor to the beginning of the page. This caused the
first page to be read twice: in that call, and later in the loop.
Address that issue by changing the call to nand_read_page_op() to
nand_change_read_column_op(), which will only reset the read cursor.
Cc: <stable@vger.kernel.org> # v5.2
Fixes: a0ac778eb8 ("mtd: rawnand: ingenic: Add support for the JZ4740")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-2-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f53d4c109a666bf1a4883b45d546fba079258717 upstream.
gpmi_io clock needs to be gated off when changing the parent/dividers of
enfc_clk_root (i.MX6Q/i.MX6UL) respectively qspi2_clk_root (i.MX6SX).
Otherwise this rate change can lead to an unresponsive GPMI core which
results in DMA timeouts and failed driver probe:
[ 4.072318] gpmi-nand 112000.gpmi-nand: DMA timeout, last DMA
...
[ 4.370355] gpmi-nand 112000.gpmi-nand: Chip: 0, Error -110
...
[ 4.375988] gpmi-nand 112000.gpmi-nand: Chip: 0, Error -22
[ 4.381524] gpmi-nand 112000.gpmi-nand: Error in ECC-based read: -22
[ 4.387988] gpmi-nand 112000.gpmi-nand: Chip: 0, Error -22
[ 4.393535] gpmi-nand 112000.gpmi-nand: Chip: 0, Error -22
...
Other than stated in i.MX 6 erratum ERR007117, it should be sufficient
to gate only gpmi_io because all other bch/nand clocks are derived from
different clock roots.
The i.MX6 reference manuals state that changing clock muxers can cause
glitches but are silent about changing dividers. But tests showed that
these glitches can definitely happen on i.MX6ULL. For i.MX7D/8MM in turn,
the manual guarantees that no glitches can happen when changing
dividers.
Co-developed-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Christian Eggers <ceggers@arri.de>
Cc: stable@vger.kernel.org
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211102202022.15551-2-ceggers@arri.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9472335eaa1452b51dc8e8edaa1a342997cb80c7 upstream.
Under certain circumstances, the timing settings calculated by
the FSMC NAND controller driver were inaccurate.
These settings led to incorrect data reads or fallback to
timing mode 0 depending on the NAND chip used.
The timing computation did not take into account the following
constraint given in SPEAr3xx reference manual:
twait >= tCEA - (tset * TCLK) + TOUTDEL + TINDEL
Enhance the timings calculation by taking into account this
additional constraint.
This change has no impact on slow timing modes such as mode 0.
Indeed, on mode 0, computed values are the same with and
without the patch.
NANDs which previously stayed in mode 0 because of fallback to
mode 0 can now work at higher speeds and NANDs which were not
working at all because of the corrupted data work at high
speeds without troubles.
Overall improvement on a Micron/MT29F1G08 (flash_speed tool):
mode0 mode3
eraseblock write speed 3220 KiB/s 4511 KiB/s
eraseblock read speed 4491 KiB/s 7529 KiB/s
Fixes: d9fb079571 ("mtd: nand: fsmc: add support for SDR timings")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211119150316.43080-5-herve.codina@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e3cdba176ba59eaf4d463d273da0718e3626140 upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: dbffc8ccdf ("mtd: rawnand: au1550: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-3-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 325fd539fc84f0aaa0ceb9d7d3b8718582473dc5 upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 612e048e6a ("mtd: rawnand: plat_nand: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-8-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 194ac63de6ff56d30c48e3ac19c8a412f9c1408e upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 553508cec2 ("mtd: rawnand: orion: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-6-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f16b7d2a5e810fcf4b15d096246d0d445da9cc88 upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 8fc6f1f042 ("mtd: rawnand: pasemi: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-7-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5b5b4dc6fcd8194b9dd38c8acdc5ab71adf44f8 upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: f6341f6448 ("mtd: rawnand: gpio: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-4-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9d8570b7fd6f4f08528ce2f5e39787a8a260cd6 upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 6dd09f775b ("mtd: rawnand: mpc5121: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-5-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6bcd2960af1b7bacb2f1e710ab0c0b802d900501 upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: d525914b5b ("mtd: rawnand: xway: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Cc: Jan Hoffmann <jan@3e8.eu>
Cc: Kestrel seventyfour <kestrelseventyfour@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Jan Hoffmann <jan@3e8.eu>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-10-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d707bb74daae07879e0fc1b4b960f8f2d0a5fe5d upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 59d9347332 ("mtd: rawnand: ams-delta: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-2-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4ebddd6540d78a7f977b3fea0261bd575c6ffe2 upstream.
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: b36bf0a0fe ("mtd: rawnand: socrates: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-9-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b5437c7b682c9a505065b4ab4716cdc951dc3c7c ]
The controller being always asserting one CS or the other, there is no
need to actually select the right target before doing a page read/write.
However, the anfc_select_target() helper actually also changes the
timing configuration and clock in the case were two different NAND chips
with different timing requirements would be used. In this situation, we
must ensure proper configuration of the controller by calling it.
As a consequence of this change, the anfc_select_target() helper is
being moved earlier in the driver.
Fixes: 88ffef1b65 ("mtd: rawnand: arasan: Support the hardware BCH ECC engine")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210526093242.183847-4-miquel.raynal@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 076de75de1e53160e9b099f75872c1f9adf41a0b ]
If the callee gpmi_alloc_dma_buffer() failed to alloc memory for
this->raw_buffer, gpmi_free_dma_buffer() will be called to free
this->auxiliary_virt. But this->auxiliary_virt is still a non-NULL
and valid ptr.
Then gpmi_alloc_dma_buffer() returns err and gpmi_free_dma_buffer()
is called again to free this->auxiliary_virt in err_out. This causes
a double free.
As gpmi_free_dma_buffer() has already called in gpmi_alloc_dma_buffer's
error path, so it should return err directly instead of releasing the dma
buffer again.
Fixes: 4d02423e9a ("mtd: nand: gpmi: Fix gpmi_nand_init() error path")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210403060905.5251-1-lyl2019@mail.ustc.edu.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55fbb9ba4f06cb6aff32daca1e1910173c13ec51 ]
In qcom_probe_nand_devices() function, the error code returned by
qcom_nand_host_init_and_register() is converted to -ENODEV in the case
of failure. This poses issue if -EPROBE_DEFER is returned when the
dependency is not available for a component like parser.
So let's restructure the error handling logic a bit and return the
actual error code in case of qcom_nand_host_init_and_register() failure.
Fixes: c76b78d8ec ("mtd: nand: Qualcomm NAND controller driver")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5200c14242fb8fa4a9b93f7fd4064d237e58785 ]
Hamming ECC doesn't cover the OOB data, so reading or writing OOB shall
always be done without ECC enabled.
This is a problem when adding JFFS2 cleanmarkers to erased blocks. If JFFS2
clenmarkers are added to the OOB with ECC enabled, OOB bytes will be changed
from ff ff ff to 00 00 00, reporting incorrect ECC errors.
Fixes: 27c5b17cd1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210224080210.23686-1-noltari@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
