[ Upstream commit d3d6b1bf85aefe0ebc0624574b3bb62f0693914c ]
Cheap monitors sometimes advertise YUV modes they don't really have
(HDMI specification mandates YUV support so even monitors without actual
support will often wrongfully advertise it) which results in YUV matches
and user forum complaints of a red tint to light colour display areas in
common desktop environments.
Moving the default RGB fall-back before YUV selection results in RGB
mode matching in most cases, reducing complaints.
Fixes: 6c3c719936 ("drm/bridge: synopsys: dw-hdmi: add bus format negociation")
Signed-off-by: Guillaume BRUN <the.cheaterman@gmail.com>
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221116143523.2126-1-the.cheaterman@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da09daf881082266e4075657fac53c7966de8e4d ]
There are two events that signal a real change of the link state: HPD going
high means the sink is newly connected or wants the source to re-read the
EDID, RX sense going low is a indication that the link has been disconnected.
Ignore the other two events that also trigger interrupts, but don't need
immediate attention: HPD going low does not necessarily mean the link has
been lost and should not trigger a immediate read of the status. RX sense
going high also does not require a detect cycle, as HPD going high is the
right point in time to read the EDID.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> (v1)
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220826185733.3213248-1-l.stach@pengutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1528038385c0a706aac9ac165eeb24044fef6825 ]
When the dw-hdmi bridge is in first place of the bridge chain, this
means there is no way to select an input format of the dw-hdmi HW
component.
Since introduction of display-connector, negotiation was broken since
the dw-hdmi negotiation code only worked when the dw-hdmi bridge was
in last position of the bridge chain or behind another bridge also
supporting input & output format negotiation.
Commit 7cd70656d128 ("drm/bridge: display-connector: implement bus fmts callbacks")
was introduced to make negotiation work again by making display-connector
act as a pass-through concerning input & output format negotiation.
But in the case where the dw-hdmi is single in the bridge chain, for
example on Renesas SoCs, with the display-connector bridge the dw-hdmi
is no more single, breaking output format.
Reported-by: Biju Das <biju.das.jz@bp.renesas.com>
Bisected-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Tested-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Fixes: 6c3c719936 ("drm/bridge: synopsys: dw-hdmi: add bus format negociation")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: add proper fixes commit]
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220204143337.89221-1-narmstrong@baylibre.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f2532d65a571ca02258b547b5b68ab2e9406fdb ]
The current ELD handling takes the internal connector ELD buffer and
shares it to the I2S and AHB sub-driver.
But with DRM_BRIDGE_ATTACH_NO_CONNECTOR, the connector is created
elsewhere (or not), and an eventual connector is known only
if the bridge chain up to a connector is enabled.
The current dw-hdmi code gets the current connector from
atomic_enable() so use the already stored connector pointer and
replace the buffer pointer with a callback returning the current
connector ELD buffer.
Since a connector is not always available, either pass an empty
ELD to the alsa HDMI driver or don't call snd_pcm_hw_constraint_eld()
in AHB driver.
Reported-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: fixed typo in commit log]
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211029135947.3022875-1-narmstrong@baylibre.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
It has been observed that resetting force in the detect function can
result in the PHY being powered down in response to hot-plug detect
being asserted, even when the HDMI connector is forced on.
Enabling debug messages and adding a call to dump_stack() in
dw_hdmi_phy_power_off() shows the following in dmesg:
[ 160.637413] dwhdmi-rockchip ff940000.hdmi: EVENT=plugin
[ 160.637433] dwhdmi-rockchip ff940000.hdmi: PHY powered down in 0 iterations
Call trace:
dw_hdmi_phy_power_off
dw_hdmi_phy_disable
dw_hdmi_update_power
dw_hdmi_detect
dw_hdmi_connector_detect
drm_helper_probe_detect_ctx
drm_helper_hpd_irq_event
dw_hdmi_irq
irq_thread_fn
irq_thread
kthread
ret_from_fork
Fixes: 381f05a7a8 ("drm: bridge/dw_hdmi: add connector mode forcing")
Signed-off-by: Jonathan Liu <net147@gmail.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201031081747.372599-1-net147@gmail.com
It doesn't hurt to add the bridge in the global bridge list also for
platform specific dw-hdmi drivers which are based on the component
framework. This can be achieved by moving the drm_bridge_add() function
call from dw_hdmi_probe() to __dw_hdmi_probe(). A counterpart movement
for drm_bridge_remove() is also needed then. Moreover, since drm_bridge_add()
initializes &bridge->hpd_mutex, this may help those platform specific
dw-hdmi drivers(based on the component framework) avoid accessing the
uninitialized mutex in drm_bridge_hpd_notify() which is called in
dw_hdmi_irq(). Putting drm_bridge_add() in __dw_hdmi_probe() just before
it returns successfully should bring no logic change for platforms based
on the DRM bridge API, which is a good choice from safety point of view.
Also, __dw_hdmi_probe() is renamed to dw_hdmi_probe() since dw_hdmi_probe()
does nothing else but calling __dw_hdmi_probe(). Similar renaming applies
to the __dw_hdmi_remove()/dw_hdmi_remove() pair.
Fixes: ec971aaa67 ("drm: bridge: dw-hdmi: Make connector creation optional")
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Cheng-Yi Chiang <cychiang@chromium.org>
Cc: Dariusz Marcinkiewicz <darekm@google.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Jose Abreu <joabreu@synopsys.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: dri-devel@lists.freedesktop.org
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1594260156-8316-2-git-send-email-victor.liu@nxp.com
When validating a mode, bridges may need to do so in the context of a
display, as specified by drm_display_info. An example is the meson
dw-hdmi bridge that needs to consider the YUV 4:2:0 output format to
perform clock calculations.
Bridges that need the display info currently retrieve it from the
drm_connector created by the bridge. This gets in the way of moving
connector creation out of bridge drivers. To make this possible, pass
the drm_display_info to drm_bridge_funcs .mode_valid().
Changes to the bridge drivers have been performed with the following
coccinelle semantic patch and have been compile-tested.
@ rule1 @
identifier funcs;
identifier fn;
@@
struct drm_bridge_funcs funcs = {
...,
.mode_valid = fn
};
@ depends on rule1 @
identifier rule1.fn;
identifier bridge;
identifier mode;
@@
enum drm_mode_status fn(
struct drm_bridge *bridge,
+ const struct drm_display_info *info,
const struct drm_display_mode *mode
)
{
...
}
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Guido Günther <agx@sigxcpu.org> # for the nwl-dsi part:
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-11-laurent.pinchart+renesas@ideasonboard.com
is_color_space_conversion() is a misnomer. It checks not only if color
space conversion is needed, but also if format conversion is needed.
This is actually desired behaviour because result of this function
determines if CSC block should be enabled or not (CSC block can also do
format conversion).
In order to clear misunderstandings, let's rework
is_color_space_conversion() to do exactly what is supposed to do and add
another function which will determine if CSC block must be enabled or
not.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304232512.51616-5-jernej.skrabec@siol.net
Most bridge drivers create a DRM connector to model the connector at the
output of the bridge. This model is historical and has worked pretty
well so far, but causes several issues:
- It prevents supporting more complex display pipelines where DRM
connector operations are split over multiple components. For instance a
pipeline with a bridge connected to the DDC signals to read EDID data,
and another one connected to the HPD signal to detect connection and
disconnection, will not be possible to support through this model.
- It requires every bridge driver to implement similar connector
handling code, resulting in code duplication.
- It assumes that a bridge will either be wired to a connector or to
another bridge, but doesn't support bridges that can be used in both
positions very well (although there is some ad-hoc support for this in
the analogix_dp bridge driver).
In order to solve these issues, ownership of the connector should be
moved to the display controller driver (where it can be implemented
using helpers provided by the core).
Extend the bridge API to allow disabling connector creation in bridge
drivers as a first step towards the new model. The new flags argument to
the bridge .attach() operation allows instructing the bridge driver to
skip creating a connector. Unconditionally set the new flags argument to
0 for now to keep the existing behaviour, and modify all existing bridge
drivers to return an error when connector creation is not requested as
they don't support this feature yet.
The change is based on the following semantic patch, with manual review
and edits.
@ rule1 @
identifier funcs;
identifier fn;
@@
struct drm_bridge_funcs funcs = {
...,
.attach = fn
};
@ depends on rule1 @
identifier rule1.fn;
identifier bridge;
statement S, S1;
@@
int fn(
struct drm_bridge *bridge
+ , enum drm_bridge_attach_flags flags
)
{
... when != S
+ if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR) {
+ DRM_ERROR("Fix bridge driver to make connector optional!");
+ return -EINVAL;
+ }
+
S1
...
}
@ depends on rule1 @
identifier rule1.fn;
identifier bridge, flags;
expression E1, E2, E3;
@@
int fn(
struct drm_bridge *bridge,
enum drm_bridge_attach_flags flags
) {
<...
drm_bridge_attach(E1, E2, E3
+ , flags
)
...>
}
@@
expression E1, E2, E3;
@@
drm_bridge_attach(E1, E2, E3
+ , 0
)
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-10-laurent.pinchart@ideasonboard.com
Pull drm updates from Dave Airlie:
"Lots of stuff in here, though it hasn't been too insane this merge
apart from dealing with the security fun.
uapi:
- export different colorspace properties on DP vs HDMI
- new fourcc for ARM 16x16 block format
- syncobj: allow querying last submitted timeline value
- DRM_FORMAT_BIG_ENDIAN defined as unsigned
core:
- allow using gem vma manager in ttm
- connector/encoder/bridge doc fixes
- allow more than 3 encoders for a connector
- displayport mst suspend/resume reprobing support
- vram lazy unmapping, uniform vram mm and gem vram
- edid cleanups + AVI informframe bar info
- displayport helpers - dpcd parser added
dp_cec:
- Allow a connector to be associated with a cec device
ttm:
- pipelining with no_gpu_wait fix
- always keep BOs on the LRU
sched:
- allow free_job routine to sleep
i915:
- Block userptr from mappable GTT
- i915 perf uapi versioning
- OA stream dynamic reconfiguration
- make context persistence optional
- introduce DRM_I915_UNSTABLE Kconfig
- add fake lmem testing under unstable
- BT.2020 support for DP MSA
- struct mutex elimination
- Tigerlake display/PLL/power management improvements
- Jasper Lake PCH support
- refactor PMU for multiple GPUs
- Icelake firmware update
- Split out vga + switcheroo code
amdgpu:
- implement dma-buf import/export without helpers
- vega20 RAS enablement
- DC i2c over aux fixes
- renoir GPU reset
- DC HDCP support
- BACO support for CI/VI asics
- MSI-X support
- Arcturus EEPROM support
- Arcturus VCN encode support
- VCN dynamic powergating on RV/RV2
amdkfd:
- add navi12/14/renoir support to kfd
radeon:
- SI dpm fix ported from amdgpu
- fix bad DMA on ppc platforms
gma500:
- memory leak fixes
qxl:
- convert to new gem mmap
exynos:
- build warning fix
komeda:
- add aclk sysfs attribute
v3d:
- userspace cleanup uapi change
i810:
- fix for underflow in dispatch ioctls
ast:
- refactor show_cursor
mgag200:
- refactor show_cursor
arcgpu:
- encoder finding improvements
mediatek:
- mipi_tx, dsi and partial crtc support for MT8183 SoC
- rotation support
meson:
- add suspend/resume support
omap:
- misc refactors
tegra:
- DisplayPort support for Tegra 210, 186 and 194.
- IOMMU-backed DMA API fixes
panfrost:
- fix lockdep issue
- simplify devfreq integration
rcar-du:
- R8A774B1 SoC support
- fixes for H2 ES2.0
sun4i:
- vcc-dsi regulator support
virtio-gpu:
- vmexit vs spinlock fix
- move to gem shmem helpers
- handle large command buffers with cma"
* tag 'drm-next-2019-11-27' of git://anongit.freedesktop.org/drm/drm: (1855 commits)
drm/amdgpu: invalidate mmhub semaphore workaround in gmc9/gmc10
drm/amdgpu: initialize vm_inv_eng0_sem for gfxhub and mmhub
drm/amd/amdgpu/sriov skip RLCG s/r list for arcturus VF.
drm/amd/amdgpu/sriov temporarily skip ras,dtm,hdcp for arcturus VF
drm/amdgpu/gfx10: re-init clear state buffer after gpu reset
merge fix for "ftrace: Rework event_create_dir()"
drm/amdgpu: Update Arcturus golden registers
drm/amdgpu/gfx10: fix out-of-bound mqd_backup array access
drm/amdgpu/gfx10: explicitly wait for cp idle after halt/unhalt
Revert "drm/amd/display: enable S/G for RAVEN chip"
drm/amdgpu: disable gfxoff on original raven
drm/amdgpu: remove experimental flag for Navi14
drm/amdgpu: disable gfxoff when using register read interface
drm/amdgpu/powerplay: properly set PP_GFXOFF_MASK (v2)
drm/amdgpu: fix bad DMA from INTERRUPT_CNTL2
drm/radeon: fix bad DMA from INTERRUPT_CNTL2
drm/amd/display: Fix debugfs on MST connectors
drm/amdgpu/nv: add asic func for fetching vbios from rom directly
drm/amdgpu: put flush_delayed_work at first
drm/amdgpu/vcn2.5: fix the enc loop with hw fini
...
Allow codec driver register callback function for plug event.
The callback registration flow:
dw-hdmi <--- hw-hdmi-i2s-audio <--- hdmi-codec
dw-hdmi-i2s-audio implements hook_plugged_cb op
so codec driver can register the callback.
dw-hdmi exports a function dw_hdmi_set_plugged_cb so platform device
can register the callback.
When connector plug/unplug event happens, report this event using the
callback.
Make sure that audio and drm are using the single source of truth for
connector status.
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Link: https://lore.kernel.org/r/20191028071930.145899-2-cychiang@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
When setting a new display mode, dw_hdmi_setup() calls
dw_hdmi_enable_video_path(), which disables all hdmi clocks, including
the audio clock.
We should only (re-)enable the audio clock if audio was already enabled
when setting the new mode.
Without this patch, on RK3288, there will be HDMI audio on some monitors
if i2s was played to headphone when the monitor was plugged.
ACER H277HU and ASUS PB278 are two of the monitors showing this issue.
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191008102145.55134-1-cychiang@chromium.org
The DDC/CI protocol involves sending a multi-byte request to the
display via I2C, which is typically followed by a multi-byte
response. The internal I2C controller only allows single byte
reads/writes or reads of 8 sequential bytes, hence DDC/CI is not
supported when the internal I2C controller is used. The I2C
transfers complete without errors, however the data in the response
is garbage. Abort transfers to/from slave address 0x37 (DDC) with
-EOPNOTSUPP, to make it evident that the communication is failing.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Sean Paul <sean@poorly.run>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191002124354.v2.1.I709dfec496f5f0b44a7b61dcd4937924da8d8382@changeid
We haven't done any backmerge for a while due to the merge window, and it
starts to become an issue for komeda. Let's bring 5.4-rc1 in.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
When transmitting IEC60985 linear PCM audio, we configure the
Aduio Sample Channel Status information in the IEC60958 frame.
The status bit is already available in iec.status of hdmi_codec_params.
This fix the issue that audio does not come out on some monitors
(e.g. LG 22CV241)
Note that these registers are only for interfaces:
I2S audio interface, General Purpose Audio (GPA), or AHB audio DMA
(AHBAUDDMA).
For S/PDIF interface this information comes from the stream.
Currently this function dw_hdmi_set_channel_status is only called
from dw-hdmi-i2s-audio in I2S setup.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190911082646.134347-1-cychiang@chromium.org
Use the new cec_notifier_conn_(un)register() functions to
(un)register the notifier for the HDMI connector, and fill in
the cec_connector_info.
Changes since v6:
- move cec_notifier_conn_unregister to a bridge detach
function,
- add a mutex protecting a CEC notifier.
Changes since v4:
- typo fix
Changes since v2:
- removed unnecessary NULL check before a call to
cec_notifier_conn_unregister,
- use cec_notifier_phys_addr_invalidate to invalidate physical
address.
Changes since v1:
Add memory barrier to make sure that the notifier
becomes visible to the irq thread once it is fully
constructed.
Signed-off-by: Dariusz Marcinkiewicz <darekm@google.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190814104520.6001-9-darekm@google.com
The dw-hdmi, kirin and imx drivers include the drm/drm_encoder_slave.h
header but don't use the encoder slave API. Remove it or replace it with
drm/drm_encoder.h as needed.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When using an I2S source using a different clock source (usually the I2S
audio HW uses dedicated PLLs, different from the HDMI PHY PLL), fixed
CTS values will cause some frequent audio drop-out and glitches as
reported on Amlogic, Allwinner and Rockchip SoCs setups.
Setting the CTS in automatic mode will let the HDMI controller generate
automatically the CTS value to match the input audio clock.
The DesignWare DW-HDMI User Guide explains:
For Automatic CTS generation
Write "0" on the bit field "CTS_manual", Register 0x3205: AUD_CTS3
The DesignWare DW-HDMI Databook explains :
If "CTS_manual" bit equals 0b this registers contains "audCTS[19:0]"
generated by the Cycle time counter according to specified timing.
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190612085147.26971-1-narmstrong@baylibre.com
Maarten needs -rc4 backmerged so he can pull in the fbcon notifier
removal topic branch into drm-misc-next.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On Rockchip rk3288-based Chromebooks when you do a suspend/resume
cycle:
1. You lose the ability to detect an HDMI device being plugged in.
2. If you're using the i2c bus built in to dw_hdmi then it stops
working.
Let's add a hook to the core dw-hdmi driver so that we can call it in
dw_hdmi-rockchip in the next commit.
NOTE: the exact set of steps I've done here in resume come from
looking at the normal dw_hdmi init sequence in upstream Linux plus the
sequence that we did in downstream Chrome OS 3.14. Testing show that
it seems to work, but if an extra step is needed or something here is
not needed we could improve it.
As part of this change we'll refactor the hardware init bits of
dw-hdmi to happen all in one function and all at the same time. Since
we need to init the interrupt mutes before we request the IRQ, this
means moving the hardware init earlier in the function, but there
should be no problems with that. Also as part of this we now
unconditionally init the "i2c" parts of dw-hdmi, but again that ought
to be fine.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190604204207.168085-1-dianders@chromium.org
