commit 9905370560d9c29adc15f4937c5a0c0dac05f0b4 upstream.
The pin configuration (done with generic pin controller helpers and
as expressed by bindings) requires children nodes with either:
1. "pins" property and the actual configuration,
2. another set of nodes with above point.
The qup_spi2_default pin configuration uses alreaady the second method
with a "pinmux" child, so configure drive-strength similarly in
"pinconf". Otherwise the PIN drive strength would not be applied.
Fixes: 8d23a00404 ("arm64: dts: qcom: db845c: add Low speed expansion i2c and spi nodes")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221010114417.29859-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1d4516f53a611b362db7ba7a8889923d469f57e1 ]
The unit address for the pinctrl node is (0x)1000b000 and not
(0x)10005000, which is the syscfg_pctl_a address instead.
This fixes the following warning:
arch/arm64/boot/dts/mediatek/mt2712e.dtsi:264.40-267.4: Warning
(unique_unit_address): /syscfg_pctl_a@10005000: duplicate
unit-address (also used in node /pinctrl@10005000)
Fixes: f0c64340b7 ("arm64: dts: mt2712: add pintcrl device node.")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221013152212.416661-5-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff02ac621634e82c0c34d02a79d402ae700cdfd0 ]
MSM8916 was originally using the "qcom,q6v5-pil" compatible for the
MSS remoteproc. Later it was decided to use SoC-specific compatibles
instead, so "qcom,msm8916-mss-pil" is now the preferred compatible.
Commit 60a05ed059 ("arm64: dts: qcom: msm8916: Add MSM8916-specific
compatibles to SCM/MSS") updated the MSM8916 device tree to make use of
the new compatible but still kept the old "qcom,q6v5-pil" as fallback.
This is inconsistent with other SoCs and conflicts with the description
in the binding documentation (which says that only one compatible should
be present). Also, it has no functional advantage since older kernels
could not handle this DT anyway (e.g. "power-domains" in the MSS node is
only supported by kernels that also support "qcom,msm8916-mss-pil").
Make this consistent with other SoCs by using only the
"qcom,msm8916-mss-pil" compatible.
Fixes: 60a05ed059 ("arm64: dts: qcom: msm8916: Add MSM8916-specific compatibles to SCM/MSS")
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220718140344.1831731-2-stephan.gerhold@kernkonzept.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1610233bc2c2cae2dff9e101e6ea5ef69cceb0e9 ]
The NAND controller size-cells should be 0 per DT bindings.
Fix the following warning produces by DT bindings check:
"
nand-controller@33002000: #size-cells:0:0: 0 was expected
nand-controller@33002000: Unevaluated properties are not allowed ('#address-cells', '#size-cells' were unexpected)
"
Fix the missing space in node name too.
Fixes: a05ea40eb3 ("arm64: dts: imx: Add i.mx8mm dtsi support")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6effe295e1a87408033c29dbcea9d5a5c8b937d5 ]
This allows the userspace to notice that there's not enough
current provided to charge the battery, and also fixes issues
with 0% SOC values being considered invalid.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a994b34b9abb9c08ee09e835b4027ff2147f9d94 ]
The 'enable-active-low' property is not a valid one.
Only 'enable-active-high' is valid, and when this property is absent
the gpio regulator will act as active low by default.
Remove the invalid 'enable-active-low' property.
Fixes: 2c66fc34e9 ("arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Link: https://lore.kernel.org/r/20220827175140.1696699-1-festevam@denx.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8123437cf46ea5a0f6ca5cb3c528d8b6db97b9c2 ]
We've found the AUX channel to be less reliable with PCLK_EDP at a
higher rate (typically 25 MHz). This is especially important on systems
with PSR-enabled panels (like Gru-Kevin), since we make heavy, constant
use of AUX.
According to Rockchip, using any rate other than 24 MHz can cause
"problems between syncing the PHY an PCLK", which leads to all sorts of
unreliabilities around register operations.
Fixes: d67a38c5a6 ("arm64: dts: rockchip: move core edp from rk3399-kevin to shared chromebook")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Link: https://lore.kernel.org/r/20220830131212.v2.1.I98d30623f13b785ca77094d0c0fd4339550553b6@changeid
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5467359a725de90b6b8d0dd865500f6373828ca ]
The Gru-Bob board does not have a pull-up resistor on its
WLAN_HOST_WAKE# pin, but Kevin does. The production/vendor kernel
specified the pin configuration correctly as a pull-up, but this didn't
get ported correctly to upstream.
This means Bob's WLAN_HOST_WAKE# pin is floating, causing inconsistent
wakeup behavior.
Note that bt_host_wake_l has a similar dynamic, but apparently the
upstream choice was to redundantly configure both internal and external
pull-up on Kevin (see the "Kevin has an external pull up" comment in
rk3399-gru.dtsi). This doesn't cause any functional problem, although
it's perhaps wasteful.
Fixes: 8559bbeeb8 ("arm64: dts: rockchip: add Google Bob")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20220822164453.1.I75c57b48b0873766ec993bdfb7bc1e63da5a1637@changeid
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58577966a42fc0b660b5e2c7c9e5a2241363ea83 ]
Currently the DT for QCS404 SoC has setup for 2 USB2 PHYs with one each
assigned to USB3 controller and USB2 controller. This assignment is
incorrect which only works by luck: as when each USB HCI comes up it
configures the *other* controllers PHY which is enough to make them
happy. If, for any reason, we were to disable one of the controllers then
both would stop working.
This was a difficult inconsistency to be caught which was found while
trying to enable USB support in u-boot. So with all the required drivers
ported to u-boot, I couldn't get the same USB storage device enumerated
in u-boot which was being enumerated fine by the kernel.
The root cause of the problem came out to be that I wasn't enabling USB2
PHY: "usb2_phy_prim" in u-boot. Then I realised that via simply disabling
the same USB2 PHY currently assigned to USB2 host controller in the
kernel disabled enumeration for USB3 host controller as well.
So fix this inconsistency by correctly assigning USB2 PHYs.
Fixes: 9375e7d719 ("arm64: dts: qcom: qcs404: Add USB devices and PHYs")
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220711083038.1518529-1-sumit.garg@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b415bb7c976f1d595ed752001c0938f702645dab ]
Hook SDMMC1 CD up with CVM GPIO02 (SOC_GPIO11) used for card detection on J4
(uSD socket) on the carrier.
Fixes: ef633bfc21 ("arm64: tegra: Enable card detect for SD card on P2888")
Signed-off-by: Tamás Szűcs <tszucs@protonmail.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c98e6e683632386a3bd284acda4342e68aec4c41 ]
The bananapi R64 (BPI-R64) experiences wrong WPS button signals.
In OpenWrt pushing the WPS button while powering on the device will set
it to recovery mode. Currently, this also happens without any user
interaction. In particular, the wrong signals appear while booting the
device or restarting it, e.g. after doing a system upgrade. If the
device is in recovery mode the user needs to manually power cycle or
restart it.
The official BPI-R64 sources set the WPS button to GPIO_ACTIVE_LOW in
the device tree. This setting seems to suppress the unwanted WPS button
press signals. So this commit changes the button from GPIO_ACTIVE_HIGH to
GPIO_ACTIVE_LOW.
The official BPI-R64 sources can be found on
https://github.com/BPI-SINOVOIP/BPI-R64-openwrt
Fixes: 0b6286dd96 ("arm64: dts: mt7622: add bananapi BPI-R64 board")
Suggested-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Nick Hainke <vincent@systemli.org>
Link: https://lore.kernel.org/r/20220630111746.4098-1-vincent@systemli.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62e8a53431145e06e503b71625a34eaa87b72b2c ]
"make dtbs_check":
arch/arm64/boot/dts/renesas/r8a774c0-cat874.dtb: thermal-zones: cpu-thermal:thermal-sensors: [[74], [0]] is too long
arch/arm64/boot/dts/renesas/r8a774c0-ek874.dtb: thermal-zones: cpu-thermal:thermal-sensors: [[79], [0]] is too long
arch/arm64/boot/dts/renesas/r8a774c0-ek874-idk-2121wr.dtb: thermal-zones: cpu-thermal:thermal-sensors: [[82], [0]] is too long
arch/arm64/boot/dts/renesas/r8a774c0-ek874-mipi-2.1.dtb: thermal-zones: cpu-thermal:thermal-sensors: [[87], [0]] is too long
arch/arm64/boot/dts/renesas/r8a77990-ebisu.dtb: thermal-zones: cpu-thermal:thermal-sensors: [[105], [0]] is too long
From schema: Documentation/devicetree/bindings/thermal/thermal-zones.yaml
Indeed, the thermal sensors on R-Car E3 and RZ/G2E support only a single
zone, hence #thermal-sensor-cells = <0>.
Fix this by dropping the bogus zero cell from the thermal sensor
specifiers.
Fixes: 8fa7d18f9e ("arm64: dts: renesas: r8a77990: Create thermal zone to support IPA")
Fixes: 8438bfda9d ("arm64: dts: renesas: r8a774c0: Create thermal zone to support IPA")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/28b812fdd1fc3698311fac984ab8b91d3d655c1c.1655301684.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7512af9f78dedea7e04225f665dad6750df7d095 ]
Currently there are two nodes named "regulator_camera". This causes the
former to be overwritten by the latter.
Fix this by renaming them to unique names, using the preferred hyphen
instead of an underscore.
While at it, update the name of the audio regulator (which was added in
the same commit) to use a hyphen.
Fixes: a1d8a344f1 ("arm64: dts: renesas: Introduce r8a774a1-beacon-rzg2m-kit")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/a9ac82bdf108162487289d091c53a9b3de393f13.1652263918.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fe17b91a7777df140d0f1433991da67ba658796c upstream.
An interrupt for USB device are shared with USB host. Set interrupt-names
property to common "dwc_usb3" instead of "host" and "peripheral".
Cc: stable@vger.kernel.org
Fixes: d7b9beb830 ("arm64: dts: uniphier: Add USB3 controller nodes")
Reported-by: Ryuta NAKANISHI <nakanishi.ryuta@socionext.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5fb779558f1c97e2bf2794cb59553e569c38e2f9 ]
"make dtbs_check" complains about the missing "-supply" suffix for
vdd_lvs1_2 which is clearly a typo, originally introduced in the
msm8994-smd-rpm.dtsi file and apparently later copied to
msm8992-xiaomi-libra.dts:
msm8992-lg-bullhead-rev-10/101.dtb: pm8994-regulators: 'vdd_lvs1_2'
does not match any of the regexes:
'.*-supply$', '^((s|l|lvs|5vs)[0-9]*)|(boost-bypass)|(bob)$', 'pinctrl-[0-9]+'
From schema: regulator/qcom,smd-rpm-regulator.yaml
msm8992-xiaomi-libra.dtb: pm8994-regulators: 'vdd_lvs1_2'
does not match any of the regexes:
'.*-supply$', '^((s|l|lvs|5vs)[0-9]*)|(boost-bypass)|(bob)$', 'pinctrl-[0-9]+'
From schema: regulator/qcom,smd-rpm-regulator.yaml
Reported-by: Rob Herring <robh@kernel.org>
Cc: Konrad Dybcio <konrad.dybcio@somainline.org>
Fixes: f3b2c99e73 ("arm64: dts: Enable onboard SDHCI on msm8992")
Fixes: 0f5cdb31e8 ("arm64: dts: qcom: Add Xiaomi Libra (Mi 4C) device tree")
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220627135938.2901871-1-stephan.gerhold@kernkonzept.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0836de513ebaae5f03014641eac996290d67493d ]
According to RM bit layout, BIT3 and BIT0 are reserved.
8 7 6 5 4 3 2 1 0
PE HYS PUE ODE FSEL X DSE X
Although function is not broken, we should not set reserved bit.
Fixes: 5e4a67ff7f ("arm64: dts: imx8mp-evk: Add i2c3 support")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b838582ab8d5fb11b2c0275056a9f34e1d94fece ]
0x19 is not a valid setting. According to RM bit layout,
BIT3 and BIT0 are reserved.
8 7 6 5 4 3 2 1 0
PE HYS PUE ODE FSEL X DSE X
Correct setting with PE PUE set, DSE set to 0.
Fixes: 50d336b12f ("arm64: dts: imx8mp-evk: Add GPIO LED support")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d4fb72b681205eed4553d8802632bd3270be3ba ]
According to the IOMUXC_SW_PAD_CTL_PAD_UART2_RXD/TXD register define in
imx8mp RM, bit0 and bit3 are reserved, and the uart2 rx/tx pin should
enable the pull up, so need to set bit8 to 1. The original pinctl value
0x49 is incorrect and needs to be changed to 0x140, same as uart1 and
uart3.
Fixes: 9e847693c6 ("arm64: dts: freescale: Add i.MX8MP EVK board support")
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4ce01ce36d77137cf60776b320babed89de6bd4c upstream.
There is a header for a DB9 serial port, but any attempts to use
hardware handshaking fail. Enable RTS and CTS pin muxing and enable
handshaking in the uart node.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0310b5aa0656a94102344f1e9ae2892e342a665d ]
The ROHM BD71847 PMIC has a 32.768 kHz clock.
Describe the PMIC clock to fix the following boot errors:
bd718xx-clk bd71847-clk.1.auto: No parent clk found
bd718xx-clk: probe of bd71847-clk.1.auto failed with error -22
Based on the same fix done for imx8mm-evk as per commit
a6a355ede5 ("arm64: dts: imx8mm-evk: Add 32.768 kHz clock to PMIC")
Fixes: 3e44dd0973 ("arm64: dts: imx8mn-ddr4-evk: Add rohm,bd71847 PMIC support")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd86d85401c2049f652293877c0f7e6e5afc3bbc ]
Amlogic SM1 devices experience CPU stalls and random board wedges when
the system idles and CPU cores clock down to lower opp points. Recent
vendor kernels include a change to remove 100-250MHz and other distro
sources also remove the 500/667MHz points. Unless all 100-667Mhz opps
are removed or the CPU governor forced to performance stalls are still
observed, so let's remove them to improve stability and uptime.
Fixes: 3d9e764830 ("arm64: dts: meson-sm1-sei610: enable DVFS")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220210100638.19130-3-christianshewitt@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c4d636bc00dc17c63ffb2a73a0da850240e26e3 ]
Amlogic G12B devices experience CPU stalls and random board wedges when
the system idles and CPU cores clock down to lower opp points. Recent
vendor kernels include a change to remove 100-250MHz and other distro
sources also remove the 500/667MHz points. Unless all 100-667Mhz opps
are removed or the CPU governor forced to performance stalls are still
observed, so let's remove them to improve stability and uptime.
Fixes: b96d4e9270 ("arm64: dts: meson-g12b: support a311d and s922x cpu operating points")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220210100638.19130-2-christianshewitt@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1bc12d301594eafde0a8529d28d459af81053b3a ]
The common touchscreen properties are all 32-bit, not 16-bit. These
properties must not be too important as they are all ignored in case of an
error reading them.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/Yk3moe6Hz8ELM0iS@robh.at.kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
