[ Upstream commit df7abcaa1246e2537ab4016077b5443bb3c09378 ]
Currently a use-after-free may occur if a sas_task is aborted by the upper
layer before we handle the I/O completion in mpi_ssp_completion() or
mpi_sata_completion().
In this case, the following are the two steps in handling those I/O
completions:
- Call complete() to inform the upper layer handler of completion of
the I/O.
- Release driver resources associated with the sas_task in
pm8001_ccb_task_free() call.
When complete() is called, the upper layer may free the sas_task. As such,
we should not touch the associated sas_task afterwards, but we do so in the
pm8001_ccb_task_free() call.
Fix by swapping the complete() and pm8001_ccb_task_free() calls ordering.
Link: https://lore.kernel.org/r/1643289172-165636-4-git-send-email-john.garry@huawei.com
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62afb379a0fee7e9c2f9f68e1abeb85ceddf51b9 ]
According to the comment in check_fw_ready() we should not check the
IOP1_READY field in register SCRATCH_PAD_1 for 8008 or 8009 controllers.
However we check this very field in process_oq() for processing the highest
index interrupt vector. The highest interrupt vector is checked as the FW
is programmed to signal fatal errors through this irq.
Change that function to not check IOP1_READY for those mentioned
controllers, but do check ILA_READY in both cases.
The reason I assume that this was not hit earlier was because we always
allocated 64 MSI(X), and just did not pass the vector index check in
process_oq(), i.e. the handler never ran for vector index 63.
Link: https://lore.kernel.org/r/1642508105-95432-1-git-send-email-john.garry@huawei.com
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1acd81bd6eb685aa9fef25624fb36d297f6404e ]
When driver is loaded after rmmod some drives are not showing up during
discovery.
SATA drives are directly attached to the controller connected phys. During
device discovery, the IDENTIFY command (qc timeout (cmd 0xec)) is timing out
during revalidation. This will trigger abort from host side and controller
successfully aborts the command and returns success. Post this successful
abort response ATA library decides to mark the disk as NODEV.
To overcome this, inside pm8001_scan_start() after phy_start() call, add get
start response and wait for few milliseconds to trigger next phy start.
This millisecond delay will give sufficient time for the controller state
machine to accept next phy start.
Link: https://lore.kernel.org/r/20210505120103.24497-1-ajish.koshy@microchip.com
Signed-off-by: Ajish Koshy <ajish.koshy@microchip.com>
Signed-off-by: Viswas G <viswas.g@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f744a14f331f56703a9d74e86520db045f11831 ]
The mpi_uninit_check() takes longer for inbound doorbell register to be
cleared. Increase the timeout substantially so that the driver does not
fail to load.
Previously, the inbound doorbell wait time was mistakenly increased in the
mpi_init_check() instead of mpi_uninit_check(). It is okay to leave the
mpi_init_check() wait time as-is as these are timeout values and if there
is a failure, waiting longer is not an issue.
Link: https://lore.kernel.org/r/20210406180534.1924345-2-ipylypiv@google.com
Fixes: e90e236250 ("scsi: pm80xx: Increase timeout for pm80xx mpi_uninit_check")
Reviewed-by: Vishakha Channapattan <vishakhavc@google.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 121181f3f839c29d8dd9fdc3cc9babbdc74227f8 ]
LLDDs report events to libsas with .notify_port_event and .notify_phy_event
callbacks.
These callbacks are fixed and so there is no reason why the functions
cannot be called directly, so do that.
This neatens the code slightly, makes it more obvious, and reduces function
pointer usage, which is generally a good thing. Downside is that there are
2x more symbol exports.
[a.darwish@linutronix.de: Remove the now unused "sas_ha" local variables]
Link: https://lore.kernel.org/r/20210118100955.1761652-3-a.darwish@linutronix.de
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b5d2793283dcb97b401b3b2c02b8a94eee29af1 ]
Every PM8001_<FOO>_DBG macro uses an internal call to pm8001_printk.
Convert all uses of:
PM8001_<FOO>_DBG(hba, pm8001_printk(fmt, ...))
to
pm8001_dbg(hba, <FOO>, fmt, ...)
so the visual complexity of each macro is reduced.
The repetitive macro definitions are converted to a single pm8001_dbg and
the level is concatenated using PM8001_##level##_LOGGING for the specific
level test.
Done with coccinelle, checkpatch and a little typing of the new macro
definition.
Miscellanea:
- Coalesce formats
- Realign arguments
- Add missing terminating newlines to formats
- Remove trailing spaces from formats
- Change defective loop with printk(KERN_INFO... to emit a 16 byte hex
block to %p16h
Link: https://lore.kernel.org/r/49f36a93af7752b613d03c89a87078243567fd9a.1605914030.git.joe@perches.com
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a2efd4b89fcaa6e9a7b4ce49a441afaacba00ea ]
Incorrect value of the running_req was causing the driver unload to be
stuck during the SAS lldd_dev_gone notification handling. During SATA I/O
completion, for some error status values, the driver schedules the event
handler and running_req is decremented from that. However, there are some
other error status values (like IO_DS_IN_RECOVERY,
IO_XFER_ERR_LAST_PIO_DATAIN_CRC_ERR) where the I/O has already been
completed by fw/driver so running_req is not decremented.
Also during NCQ error handling, driver itself will initiate READ_LOG_EXT
and ABORT_ALL. When libsas/libata initiate READ_LOG_EXT (0x2F), driver
increments running_req. This will be completed by the driver in
pm80xx_chip_sata_req(), but running_req was not decremented.
Link: https://lore.kernel.org/r/20201102165528.26510-3-Viswas.G@microchip.com.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7640e1eb8c5de33dafa6c68fd4389214ff9ec1f9 ]
Driver submits all internal requests (like abort_task, event acknowledgment
etc.) through inbound queue 0. While submitting those, driver does not
acquire any lock and this may lead to a race when there is an I/O request
coming in on CPU0 and submitted through inbound queue 0. To avoid this,
lock acquisition has been moved to pm8001_mpi_build_cmd(). All command
submission will go through this path.
Link: https://lore.kernel.org/r/20201102165528.26510-2-Viswas.G@microchip.com.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: peter chang <dpf@google.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ba9e516573e60c471c01bb369144651f6f8d50b ]
hw_event_sas_phy_up() is used in hardirq/softirq context:
pm8001_interrupt_handler_msix() || pm8001_interrupt_handler_intx() || pm8001_tasklet
=> PM8001_CHIP_DISP->isr() = pm80xx_chip_isr()
=> process_oq() [spin_lock_irqsave(&pm8001_ha->lock,)]
=> process_one_iomb()
=> mpi_hw_event()
=> hw_event_sas_phy_up()
=> msleep(200)
Revert the msleep() back to an mdelay() to avoid sleeping in atomic
context.
Link: https://lore.kernel.org/r/20201126132952.2287996-2-bigeasy@linutronix.de
Fixes: 4daf1ef3c6 ("scsi: pm80xx: Convert 'long' mdelay to msleep")
Cc: Vikram Auradkar <auradkar@google.com>
Cc: Jack Wang <jinpu.wang@cloud.ionos.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Current driver uses fixed number of Inbound and Outbound queues and all of
the I/O, TMF and internal requests are submitted through those. A global
spin lock is used to control the shared access. This can create a lock
contention and it is real bottleneck in the I/O path.
To avoid this, the number of supported Inbound and Outbound queues is
increased to 64, and the number of queues used is decided based on number
of CPU cores online and number of MSI-X vectors allocated. Also add locks
per queue instead of using the global lock.
Link: https://lore.kernel.org/r/20201005145011.23674-2-Viswas.G@microchip.com.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull SCSI updates from James Bottomley:
"This consists of the usual driver updates (ufs, qla2xxx, tcmu, lpfc,
hpsa, zfcp, scsi_debug) and minor bug fixes.
We also have a huge docbook fix update like most other subsystems and
no major update to the core (the few non trivial updates are either
minor fixes or removing an unused feature [scsi_sdb_cache])"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (307 commits)
scsi: scsi_transport_srp: Sanitize scsi_target_block/unblock sequences
scsi: ufs-mediatek: Apply DELAY_AFTER_LPM quirk to Micron devices
scsi: ufs: Introduce device quirk "DELAY_AFTER_LPM"
scsi: virtio-scsi: Correctly handle the case where all LUNs are unplugged
scsi: scsi_debug: Implement tur_ms_to_ready parameter
scsi: scsi_debug: Fix request sense
scsi: lpfc: Fix typo in comment for ULP
scsi: ufs-mediatek: Prevent LPM operation on undeclared VCC
scsi: iscsi: Do not put host in iscsi_set_flashnode_param()
scsi: hpsa: Correct ctrl queue depth
scsi: target: tcmu: Make TMR notification optional
scsi: target: tcmu: Implement tmr_notify callback
scsi: target: tcmu: Fix and simplify timeout handling
scsi: target: tcmu: Factor out new helper ring_insert_padding
scsi: target: tcmu: Do not queue aborted commands
scsi: target: tcmu: Use priv pointer in se_cmd
scsi: target: Add tmr_notify backend function
scsi: target: Modify core_tmr_abort_task()
scsi: target: iscsi: Fix inconsistent debug message
scsi: target: iscsi: Fix login error when receiving
...
These are not invoked externally.
Fixes the following W=1 kernel build warning(s):
drivers/scsi/pm8001/pm80xx_hwi.c:69:6: warning: no previous prototype for ‘pm80xx_pci_mem_copy’ [-Wmissing-prototypes]
69 | void pm80xx_pci_mem_copy(struct pm8001_hba_info *pm8001_ha, u32 soffset,
| ^~~~~~~~~~~~~~~~~~~
drivers/scsi/pm8001/pm80xx_hwi.c:5016:6: warning: no previous prototype for ‘mpi_set_phy_profile_req’ [-Wmissing-prototypes]
5016 | void mpi_set_phy_profile_req(struct pm8001_hba_info *pm8001_ha,
| ^~~~~~~~~~~~~~~~~~~~~~~
Link: https://lore.kernel.org/r/20200721164148.2617584-26-lee.jones@linaro.org
Cc: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/pm8001/pm80xx_hwi.c:918: warning: Function parameter or member 'number' not described in 'update_inbnd_queue_table'
drivers/scsi/pm8001/pm80xx_hwi.c:954: warning: Function parameter or member 'number' not described in 'update_outbnd_queue_table'
drivers/scsi/pm8001/pm80xx_hwi.c:1717: warning: Function parameter or member 'vec' not described in 'pm80xx_chip_interrupt_enable'
drivers/scsi/pm8001/pm80xx_hwi.c:1735: warning: Function parameter or member 'vec' not described in 'pm80xx_chip_interrupt_disable'
drivers/scsi/pm8001/pm80xx_hwi.c:4830: warning: Excess function parameter 'num' description in 'pm80xx_chip_phy_start_req'
drivers/scsi/pm8001/pm80xx_hwi.c:4872: warning: Excess function parameter 'num' description in 'pm80xx_chip_phy_stop_req'
drivers/scsi/pm8001/pm80xx_hwi.c:4892: warning: Function parameter or member 'pm8001_ha' not described in 'pm80xx_chip_reg_dev_req'
drivers/scsi/pm8001/pm80xx_hwi.c:4892: warning: Function parameter or member 'pm8001_dev' not described in 'pm80xx_chip_reg_dev_req'
drivers/scsi/pm8001/pm80xx_hwi.c:4892: warning: Function parameter or member 'flag' not described in 'pm80xx_chip_reg_dev_req'
drivers/scsi/pm8001/pm80xx_hwi.c:4966: warning: Function parameter or member 'phyId' not described in 'pm80xx_chip_phy_ctl_req'
drivers/scsi/pm8001/pm80xx_hwi.c:4966: warning: Function parameter or member 'phy_op' not described in 'pm80xx_chip_phy_ctl_req'
drivers/scsi/pm8001/pm80xx_hwi.c:4966: warning: Excess function parameter 'num' description in 'pm80xx_chip_phy_ctl_req'
drivers/scsi/pm8001/pm80xx_hwi.c:4966: warning: Excess function parameter 'phy_id' description in 'pm80xx_chip_phy_ctl_req'
drivers/scsi/pm8001/pm80xx_hwi.c:5006: warning: Function parameter or member 'vec' not described in 'pm80xx_chip_isr'
drivers/scsi/pm8001/pm80xx_hwi.c:5006: warning: Excess function parameter 'irq' description in 'pm80xx_chip_isr'
drivers/scsi/pm8001/pm80xx_hwi.c:5006: warning: Excess function parameter 'stat' description in 'pm80xx_chip_isr'
Link: https://lore.kernel.org/r/20200721164148.2617584-18-lee.jones@linaro.org
Cc: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added the sysfs attribute for non fatal log so that management utility can
get the non fatal dump from driver. The non-fatal error is an error
condition or abnormal behavior detected by the host, or detected and
reported by the controller to the host.The non-fatal error does not stop
the controller firmware and enables it to still respond to host requests.
A typical example of a non-fatal error is an I/O timeout or an unusual
error notification from the controller. Since the firmware is operational,
the error dump information is pushed to host memory (by firmware) upon
request from the host.
Link: https://lore.kernel.org/r/20200316074906.9119-6-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In pm80xx driver, the command mpi_set_phy_profile_req is sent by host
during boot to configure the phy profile such as analog setting page, rate
control page. However, the tag is not freed when its response is
received. As a result, 16 tags are missing for each HBA after boot. When
NCQ is enabled with queue depth 16, it needs at least, 15 * 16 = 240 tags
for each HBA to achieve the best performance. In current pm80xx driver with
setting CCB_MAX = 256, the total number of tags in each HBA is 255 for data
IO. Hence, without returning those tags to the pool after boot, some device
will finally be forced to non-ncq mode by ATA layer due to excessive errors
(i.e. LLDD cannot allocate tag for queued task).
Link: https://lore.kernel.org/r/20200316074906.9119-4-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: yuuzheng <yuuzheng@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A kexec reboot causes the controller fw to assert. This assertion shows up
in two ways, the controller doesn't show up as ready and an interrupt is
waiting as soon as the handler is registered. To resolve this added below
fix:
- Split the interrupt handling setup into two parts, setup and request.
- If the controller ready register indicates not-ready, but that the not
readiness is only on the IOC units we can still try a reset to bring the
system back to the pre-reboot state.
Link: https://lore.kernel.org/r/20200316074906.9119-3-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Vikram Auradkar <auradkar@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The condition (reg_val != 2) || (reg_val != 3) will always be true because
reg_val cannot be equal to two different values at the same time. Fix this
by replacing the || operator with && so that the loop will loop if reg_val
is not a 2 and not a 3 as was originally intended.
Fixes: 50dc2f221455 ("scsi: pm80xx: Modified the logic to collect fatal dump")
Link: https://lore.kernel.org/r/20191120135031.270708-1-colin.king@canonical.com
Addresses-Coverity: ("Constant expression result")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The commands to the controller are sent in fixed sized chunks which are set
per-chip-generation and stashed in iomb_size. The driver fills in structs
matching the register layout and memcpy this to memory shared with the
controller. However, there are two problem cases:
1) Things like phy_start_req are too large because they share the
sas_identify_frame definition with libsas, and it includes the crc
word. This means that it's overwriting the start of the next
command block, that's ok except if it happens at the end of the
shared memory area.
2) Things like set_nvm_data_req which are shared between the HAL
layers. This means that it's sending 'random' data for things that
are in the reserved area. So far we haven't found a case where the
controller FW cares, but sending possible gibberish (for most of
the structures this is in the reserved area so previously zeroed)
is not recommended.
Link: https://lore.kernel.org/r/20191114100910.6153-9-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: peter chang <dpf@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Disabling the SATA drive interface cause kernel panic. When the drive
Interface is disabled, device should be deregistered after aborting all
pending I/Os. Also changed the port recovery timeout to 10000 ms for
PM8006 controller.
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Reviewed-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Many times in libsas, and in LLDDs which use libsas, the check for an
expander device is re-implemented or open coded.
Use dev_is_expander() instead. We rename this from
sas_dev_type_is_expander() to not spill so many lines in referencing.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rename the functions pm8001_chip_is_our_interupt,
pm80xx_chip_is_our_interupt and function pointer is_our_interrupt to fix
spelling mistakes.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When macro PM8001_USE_MSIX is defined there are redundant dead code calls
to pm8001_chip_intx_interrupt_{enable|disable} and pm8001_cr32.
Clean this up for the defined PM8001_USE_MSIX and undefined
PM8001_USE_MSIX cases.
[mkp: squashed two patches]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/pm8001/pm80xx_hwi.c: In function 'pm8001_set_phy_profile':
drivers/scsi/pm8001/pm80xx_hwi.c:4679:6: warning:
variable 'page_code' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the firmware is not responding, execution of kexec boot causes a system
hang. When firmware assertion happened, driver get notified with interrupt
vector updated in MPI configuration table. Then, the driver will read
scratchpad register and set controller_fatal_error flag to true.
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
when there's an error in 'ncq mode' the host has to read the ncq error
log (10h) to clear the error state. however, the ccb that is setup for
doing this doesn't setup the ccb so that the previous state is
cleared. if the ccb was previously used for an IO n_elems is set and
pm8001_ccb_task_free() treats this as the signal to go free a
scatter-gather list (that's already been freed).
Signed-off-by: Deepak Ukey <deepak.ukey@microsemi.com>
Signed-off-by: Viswas G <Viswas.G@microsemi.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Modified SATA abort handling with following steps:
1) Set device state as recovery.
2) Send phy reset.
3) Wait for reset completion.
4) After successful reset, abort all IO's to the device.
5) After aborting all IO's to device, set device state as operational.
Signed-off-by: Deepak Ukey <deepak.ukey@microsemi.com>
Signed-off-by: Viswas G <Viswas.G@microsemi.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ATTO adapters do not support this feature. If the firmware fails to be
ready, it should not check the examined registers in order to examine
the state of the feature in order to prevent undefined behavior.
Signed-off-by: Benjamin Rood <brood@attotech.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
PHY profiles are not saved in NVRAM on ATTO 12Gb SAS controllers.
Therefore, in order for the controller to function in a wide range of
configurations, the PHY profiles must be statically set. This patch
provides the necessary functionality to do so.
Signed-off-by: Benjamin Rood <brood@attotech.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In case psataPayload->status has a status of IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY
ts->stat gets set to SAS_OPEN_REJECT but a missing 'break' statement causes a
fallthrough to the default handler of the switch statement overriding ts->stat
to SAS_DEV_NO_RESPONSE.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
PORT RECOVERY TIMEOUT is the maximum time between the controller's
detection of the PHY down until the receipt of the ID_Frame (from the
same remote SAS port). If the time expires before the ID_FRAME is
received, the port is considered INVALID and can be removed. The
IOP_EVENT_PORT_RECOVERY_TIMER_TMO event is reported following the
IOP_EVENT_ PHY_DOWN event when the PHY/port does not recover after
Port Recovery Time.
Signed-off-by: Viswas G <Viswas.G@pmcs.com>
Reviewed-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
