Calculate the low and high watermarks based on the low and high
clocks for the current power state. The dynamic pm hw will select
the appropriate watermark based on the internal dpm state.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Newer asics have a lot of vram so it's less of an
issue to waste a little more space for the gart
page table. This gives us some additional gart space
before having to migrate to non-gart system ram
for games, etc. where we use up most of vram.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1. Handle the the thermal state directly in the work handler.
Remove the state selection function since nothing else uses it now.
2. On some asics there is no thermal state, so we just use a regular
state and force the low performance state.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use the UVD handle information to determine which
which power states to select when using UVD. For
example, decoding a single SD stream requires much
lower clocks than multiple HD streams.
v2: switch to a cleaner dpm/uvd interface
v3: change the uvd power state while streams
are active if need be
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a helper function for counting the number of open stream handles.
v2: fix copy-pasta in comments and whitespace error
v3: make function static since it's only used in radeon_uvd.c
at the moment
v4: make non-static again for future changes
v5: make static again for new rework of dpm uvd changes
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This introduces the helper functions which can be used by several
mtd/tests modules.
The following three functions are used all over the test modules.
- mtdtest_erase_eraseblock()
- mtdtest_scan_for_bad_eraseblocks()
- mtdtest_erase_good_eraseblocks()
The following are wrapper functions for mtd_read() and mtd_write()
which can simplify the return value check.
- mtdtest_read()
- mtdtest_write()
All helpers are put into a single .c file and it will be linked to
every test module later. The code will actually be copied to every
test module, but it is fine for our small test infrastructure.
[dwmw2: merge later 'return -EIO when mtdtest_read() failed' fix]
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Vikram Narayanan <vikram186@gmail.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This ASSERT is testing an if_flags flag value against
a di_aformat enum value. di_aformat is never assigned
XFS_IFINLINE.
This happens to work for now, because XFS_IFINLINE has
the same value as XFS_DINODE_FMT_LOCAL, and that's tested
just before we call this function.
However, I think the intention is to assert that we have
read in the data, i.e. XFS_IFINLINE on if_flags, before
we use if_data. This is done in other places through the
code as well.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ben Myers <bpm@sgi.com>
Should a connect fail, if the publication/server is unavailable or
due to some other error, a positive value will be returned and errno
is never set. If the application code checks for an explicit zero
return from connect (success) or a negative return (failure), it
will not catch the error and subsequent send() calls will fail as
shown from the strace snippet below.
socket(0x1e /* PF_??? */, SOCK_SEQPACKET, 0) = 3
connect(3, {sa_family=0x1e /* AF_??? */, sa_data="\2\1\322\4\0\0\322\4\0\0\0\0\0\0"}, 16) = 111
sendto(3, "test", 4, 0, NULL, 0) = -1 EPIPE (Broken pipe)
The reason for this behaviour is that TIPC wrongly inverts error
codes set in sk_err.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 90ba9b19 (tcp: tcp_make_synack() can use alloc_skb()), Eric changed
the call to sock_wmalloc in tcp_make_synack to alloc_skb. In doing so,
the netfilter owner match lost its ability to block the SYNACK packet on
outbound listening sockets. Revert the change, restoring the owner match
functionality.
This closes netfilter bugzilla #847.
Signed-off-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the current CPU has no cpuidle driver, drv will be NULL in
cpuidle_driver_ref(). Check if that is the case before trying
to bump up the driver's refcount to prevent the kernel from
crashing.
[rjw: Subject and changelog]
Signed-off-by: Daniel Fu <danifu@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 71472c0 (clk: add support for clock reparent on set_rate) added a
dereference of the new_parent pointer in clk_reparent(), but as detected
by smatch clk_reparent() later checks whether new_parent is NULL.
The dereference was in order to clear the new parent's new_child pointer
to avoid duplicate POST_RATE_CHANGE notifications, so clearly isn't
necessary if the new parent is NULL, so move it inside the "if
(new_parent)" block.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Currently we would still potentially suffer multicast packet loss if there
is just either an IGMP or an MLD querier: For the former case, we would
possibly drop IPv6 multicast packets, for the latter IPv4 ones. This is
because we are currently assuming that if either an IGMP or MLD querier
is present that the other one is present, too.
This patch makes the behaviour and fix added in
"bridge: disable snooping if there is no querier" (b00589af3b)
to also work if there is either just an IGMP or an MLD querier on the
link: It refines the deactivation of the snooping to be protocol
specific by using separate timers for the snooped IGMP and MLD queries
as well as separate timers for our internal IGMP and MLD queriers.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTT cached in the TCP metrics are valuable for the initial timeout
because SYN RTT usually does not account for serialization delays
on low BW path.
However using it to seed the RTT estimator maybe disruptive because
other components (e.g., pacing) require the smooth RTT to be obtained
from actual connection.
The solution is to use the higher cached RTT to set the first RTO
conservatively like tcp_rtt_estimator(), but avoid seeding the other
RTT estimator variables such as srtt. It is also a good idea to
keep RTO conservative to obtain the first RTT sample, and the
performance is insured by TCP loss probe if SYN RTT is available.
To keep the seeding formula consistent across SYN RTT and cached RTT,
the rttvar is twice the cached RTT instead of cached RTTVAR value. The
reason is because cached variation may be too small (near min RTO)
which defeats the purpose of being conservative on first RTO. However
the metrics still keep the RTT variations as they might be useful for
user applications (through ip).
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In optimising the CIL operations, some of the IOP_* macros for
calling log item operations were removed. Remove the rest of them as
Christoph requested.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Geoffrey Wehrman <gwehrman@sgi.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Change the SERIAL_AR933X Kconfig option from
'bool' to 'tristate' in order to allow to build
the driver as a module. Also extend the help text
of the option to reflect that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
h8300 does not support PARPORT_PC.
The related error (with allmodconfig for h8300):
CC [M] drivers/parport/parport_pc.o
drivers/parport/parport_pc.c:67:25: fatal error: asm/parport.h: No such file or directory
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If st_kim_start() fails registered protocols should be removed. This is
done by calling st_reg_complete(), which as comment states is called
with spin lock held. But in st_register() when st_kim_start fails it
is called without holding spin lock, creating possibility of concurrent
access to st_gdata data members.
Hold spin lock while calling st_reg_complete if st_kim_start() fails.
Signed-off-by: Oleksandr Kozaruk <oleksandr.kozaruk@globallogic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code would attempt to negotiate a different protocol version if
the current negotiation timed out. This triggers an assert in the host (on debug
builds). Avoid this by negotiating a newer version only if the host properly
rejects the current version being negotiated.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Got the following oops just before reboot:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
[<8028d300>] (__list_del_entry+0x44/0xac)
[<802e3320>] (__fw_load_abort.part.13+0x1c/0x50)
[<802e337c>] (fw_shutdown_notify+0x28/0x50)
[<80034f80>] (notifier_call_chain.isra.1+0x5c/0x9c)
[<800350ec>] (__blocking_notifier_call_chain+0x44/0x58)
[<80035114>] (blocking_notifier_call_chain+0x14/0x18)
[<80035d64>] (kernel_restart_prepare+0x14/0x38)
[<80035d94>] (kernel_restart+0xc/0x50)
The following race condition triggers here:
_request_firmware_load()
device_create_file(...)
kobject_uevent(...)
(schedule)
(resume)
firmware_loading_store(1)
firmware_loading_store(0)
list_del_init(&buf->pending_list)
(schedule)
(resume)
list_add(&buf->pending_list, &pending_fw_head);
wait_for_completion(&buf->completion);
causing an oops later when walking pending_list after the firmware has
been released.
The proposed fix is to move the list_add() before sysfs attribute
creation.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Acked-by: Ming Lei <ming.lei@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In usb_reset_and_verify_device(), hub_port_init() allocates a new bos
descriptor to hold the value read by the device. The new bos descriptor
has to be compared with the old one in order to figure out if device 's
firmware has changed in which case the device has to be reenumerated.
In the original code, none of the two descriptors was deallocated leading
to memory leaks.
This patch compares the old bos descriptor with the new one to detect change
in firmware and releases the newly allocated bos descriptor to prevent memory
leak.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Reported-by: Martin MOKREJS <mmokrejs@gmail.com>
Tested-by: Martin MOKREJS <mmokrejs@gmail.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the ehci statictics information output in ehci_stop()
because they do not provide interesting info. At any case, the current
statistics can be viewed by reading the 'registers' file in debugfs.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the duplicate of debug_async_open() prototype following
three lines below the debug_async_open() declaration.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The debugging code for ehci is enabled to run if the DEBUG flag is defined.
This patch enables the debugging code also when the kernel is configured
with dynamic debugging on.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes ehci_vdbg debugging statements from EHCI host controller
driver because they produce too much information, lowering the signal to noise
ratio when debugging, and because they are not used anymore.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We've been seeing occasional problems with log space leaks and
transaction underruns such as this for some time:
XFS (dm-0): xlog_write: reservation summary:
trans type = FSYNC_TS (36)
unit res = 2740 bytes
current res = -4 bytes
total reg = 0 bytes (o/flow = 0 bytes)
ophdrs = 0 (ophdr space = 0 bytes)
ophdr + reg = 0 bytes
num regions = 0
Turns out that xfstests generic/311 is reliably reproducing this
problem with the test it runs at sequence 16 of it execution. It is
a 100% reliable reproducer with the mkfs configuration of "-b
size=1024 -m crc=1" on a 10GB scratch device.
The problem? Inode forks in btree format are logged in memory
format, not disk format (i.e. bmbt format, not bmdr format). That
means there is a btree block header being logged, when such a
structure is never written to the inode fork in bmdr format. The
bmdr header in the inode is only 4 bytes, while the bmbt header is
24 bytes for v4 filesystems and 72 bytes for v5 filesystems.
We currently reserve the inode size plus the rounded up overhead of
a logging a buffer, which is 128 bytes. That means the reservation
for a 512 byte inode is 640 bytes. What we can actually log is:
inode core, data and attr fork = 512 bytes
inode log format + log op header = 56 + 12 = 68 bytes
data fork bmbt hdr = 24/72 bytes
attr fork bmbt hdr = 24/72 bytes
So, for a v2 inodes we can log at least 628 bytes, but if we split that
inode over the end of the log across log buffers, we need to also
another log op header, which takes us to 640 bytes. If there's
another reservation taken out of this that I haven't taken into
account (perhaps multiple iclog splits?) or I haven't corectly
calculated the bmbt format space used (entirely possible), then
we will overun it.
For v3 inodes the maximum is actually 724 bytes, and even a
single maximally sized btree format fork can blow it (652 bytes).
And that's exactly what is happening with the FSYNC_TS transaction
in the above output - it's consumed 644 bytes of space after the CIL
context took the space reserved for it (2100 bytes).
This problem has always been present in the XFS code - the btree
format inode forks have always been logged in this manner. Hence
there has always been the possibility of an overrun with such a
transaction. The CRC code has just exposed it frequently enough to
be able to debug and understand the root cause....
So, let's fix all the inode log space reservations.
[ I'm so glad we spent the effort to clean up the transaction
reservation code. This is an easy fix now. ]
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Otherwise any attempt to interact with the hardware will crash. This is
what happens when drivers get written blind.
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Mike Turquette <mturquette@linaro.org>
kbuild bot reported following m68k build error :
net/sched/sch_fq.c: In function 'fq_dequeue':
>> net/sched/sch_fq.c:491:2: error: implicit declaration of function
'prefetch' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
While we are fixing this, move this prefetch() call a bit earlier.
Reported-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to xfs_inobt_get_rec() in xfs_dialloc_ag() passes 'j' as
the output status variable. The immediately following
XFS_WANT_CORRUPTED_GOTO() checks the value of 'i,' which is from
the previous lookup call and has already been checked. Fix the
corruption check to use 'j.'
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
many of the macros defined in Version.h are not being used,
so we can remove the file.
Signed-off-by: navin patidar <navinp@cdac.in>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"keyid" is used as an offset into the ->dot11DefKey[] array. The array
has 4 elements.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Obviously it's impossible for ->KeyLength to be both 5 and 13. I assume
that && was intended here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The result from crystalhd_get_sgle_paddr and crystalhd_get_sgle_len are later
used in calculations, so the result should be in CPU byte ordering.
Signed-off-by: Shaun Laing <shaun@xresource.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 0-DAY kernel build testing backend reports the following compiler
warnings not shown on my compiler version/options:
drivers/staging/rtl8188eu/os_dep/ioctl_linux.c: In function 'rtw_mp_efuse_get':
>> drivers/staging/rtl8188eu/os_dep/ioctl_linux.c:5836:65: warning: iteration 16u invokes undefined behavior [-Waggressive-loop-optimizations]
sprintf(extra, "%s%02X ", extra, pEfuseHal->fakeEfuseInitMap[i+j]);
^
drivers/staging/rtl8188eu/os_dep/ioctl_linux.c:5830:3: note: containing loop
for (i = 0; i < EFUSE_MAP_SIZE; i += 16) {
^
>> drivers/staging/rtl8188eu/os_dep/ioctl_linux.c:6042:69: warning: iteration 16u invokes undefined behavior [-Waggressive-loop-optimizations]
sprintf(extra, "%s %02X", extra, pEfuseHal->fakeEfuseModifiedMap[i+j]);
^
drivers/staging/rtl8188eu/os_dep/ioctl_linux.c:6036:3: note: containing loop
for (i = 0; i < EFUSE_MAP_SIZE; i += 16) {
^
The problem is due to improper settings for some of the EFUSE_XXX defines such that
EFUSE_MAP_SIZE was larger than the sizes of the marked arrays. Thanks to
Fengguang Wu for helping me understand the root cause.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CRC enabled filesystems fail log recovery with 100% reliability on
xfstests xfs/085 with the following failure:
XFS (vdb): Mounting Filesystem
XFS (vdb): Starting recovery (logdev: internal)
XFS (vdb): Corruption detected. Unmount and run xfs_repair
XFS (vdb): bad inode magic/vsn daddr 144 #0 (magic=0)
XFS: Assertion failed: 0, file: fs/xfs/xfs_inode_buf.c, line: 95
The problem is that the inode buffer has not been recovered before
the readahead on the inode buffer is issued. The checkpoint being
recovered actually allocates the inode chunk we are doing readahead
from, so what comes from disk during readahead is essentially
random and the verifier barfs on it.
This inode buffer readahead problem affects non-crc filesystems,
too, but xfstests does not trigger it at all on such
configurations....
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Log recovery has some strict ordering requirements which unordered
or reordered metadata writeback can defeat. This can occur when an
item is logged in a transaction, written back to disk, and then
logged in a new transaction before the tail of the log is moved past
the original modification.
The result of this is that when we read an object off disk for
recovery purposes, the buffer that we read may not contain the
object type that recovery is expecting and hence at the end of the
checkpoint being recovered we have an invalid object in memory.
This isn't usually a problem, as recovery will then replay all the
other checkpoints and that brings the object back to a valid and
correct state, but the issue is that while the object is in the
invalid state it can be flushed to disk. This results in the object
verifier failing and triggering a corruption shutdown of log
recover. This is correct behaviour for the verifiers - the problem
is that we are not detecting that the object we've read off disk is
newer than the transaction we are replaying.
All metadata in v5 filesystems has the LSN of it's last modification
stamped in it. This enabled log recover to read that field and
determine the age of the object on disk correctly. If the LSN of the
object on disk is older than the transaction being replayed, then we
replay the modification. If the LSN of the object matches or is more
recent than the transaction's LSN, then we should avoid overwriting
the object as that is what leads to the transient corrupt state.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
When testing LSN ordering code for v5 superblocks, it was discovered
that the the LSN embedded in the generic btree blocks was
occasionally uninitialised. These values didn't get written to disk
by metadata writeback - they got written by previous transactions in
log recovery.
The issue is here that the when the block is first allocated and
initialised, the LSN field was not initialised - it gets overwritten
before IO is issued on the buffer - but the value that is logged by
transactions that modify the header before it is written to disk
(and initialised) contain garbage. Hence the first recovery of the
buffer will stamp garbage into the LSN field, and that can cause
subsequent transactions to not replay correctly.
The fix is simply to initialise the bb_lsn field to zero when we
initialise the block for the first time.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
