It is possible for some versions of firmware to advertise capabilities that driver
is not ready to handle. This may lead to controller stall. Since the driver is
interested only in subset of flags, clearing the rest.
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There might be a crash as during shutdown flow CNIC might try
to access resources already freed by bnx2x.
Change bnx2x_close() into dev_close() in __bnx2x_remove (shutdown flow)
to guarantee CNIC is notified of the device's change of status.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTE write access error might occur in MF_ALLOWED mode when IOMMU
is active. The patch adds rmmod HSI indicating to MFW to stop
running queries which might trigger this failure.
Signed-off-by: Barak Witkowsky <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ETS can be enabled as a result of DCB negotiation, then
fairness must be recalculated after each negotiation.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add locking to protect different statistics flows from
running simultaneously.
This in order to serialize statistics requests sent to FW,
otherwise two outstanding queries may cause FW assert.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
This is a batch of updates intended for 3.12. It is mostly driver
stuff, although Johannes Berg and Simon Wunderlich make a good
showing with mac80211 bits (particularly some work on 5/10 MHz
channel support).
The usual suspects are mostly represented. There are lots of updates
to iwlwifi, ath9k, ath10k, mwifiex, rt2x00, wil6210, as usual.
The bcma bus gets some love this time, as do cw1200, iwl4965, and a
few other bits here and there. I don't think there is much unusual
here, FWIW.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The new IP version which is present in AM43xx SoC has a minor changes and the
offsets are same as the previous version, so adding new IP version support in
the driver.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eTSEC has Rx and Tx flow control capabilities that may be enabled
through MACCFG1[Rx_Flow, Tx_Flow] bits. These bits must not be set
however when eTSEC is operated in Half-Duplex mode. Unfortunately,
the driver currently sets these bits unconditionally.
This patch adds the proper handling of the PAUSE frame capability
register bits by implementing the ethtool -A interface. When pause
autoneg is enabled, the controller uses the phy's capability to
negotiate PAUSE frame settings with the link partner and reconfigures
its Rx_Flow and Tx_Flow settings to match the capabilities of the
link partner. If pause autoneg is off, the PAUSE frame generation
may be forced manually (ethtool -A). Flow control is disabled by
default now.
This implementation is inspired by the tg3 driver.
Signed-off-by: Lutz Jaenicke <ljaenicke@innominate.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMA sync should sync the whole receive buffer, not just
part of it. Fixes log messages dma_sync_check.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recognize XRC QPs in the SR-IOV resource tracker based on transport
type. The previous check didn't match IB_QPT_XRC_INI and caused an
invalid calculation for required mtt pages.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In stmmac_init_rx_buffers():
* add missing handling of dma_map_single() error
* remove superfluous unlikely() optimization while at it
Add stmmac_free_rx_buffers() helper and use it in dma_free_rx_skbufs().
In init_dma_desc_rings():
* add missing handling of kmalloc_array() errors
* fix handling of dma_alloc_coherent() and stmmac_init_rx_buffers() errors
* make function return an error value on error and 0 on success
In stmmac_open():
* add handling of init_dma_desc_rings() return value
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New routine has been added to avoid duplication of code to wait for
pending PCI transactions to complete. This makes use of that routine.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Acked-by: David S. Miller <davem@davemloft.net>
The Compressed LIP region is used to hold a limited number of Local
IPv6 addresses. This region is primarily used to reduce the TCAM
space consumed for an IPv6 offloaded connection. A 128-bit LIP will
be reduced to 13-bit and stored in the TCAM if there is a match
between the IPv6 tuple's LIP and the one stored in the CLIP region.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add cxgb4_create_server6 and cxgb4_remove_server routines to create
and remove listening IPv6 servers.
Return success (0) from cxgb4_create_server in case of ctrl queue
congestion since in case of congestion, passive open request gets
queued and gets processed later. If a non-zero value were returned it
would be treated as an error and the ULD would free STID, which can
result in an error in passive open reply.
Add cpl structure for active open request with IPv6 address for T5.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The MOXA UC-711X hardware(s) has an ethernet controller that seem
to be developed internally. The IC used is "RTL8201CP".
Since there is no public documentation, this driver is mostly the
one published by MOXA that has been heavily cleaned up / ported
from linux 2.6.9.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI core will initialize device MSI/MSI-X capability in
pci_msi_init_pci_dev(). So device driver should use
pci_dev->msi_cap/msix_cap to determine whether the device
support MSI/MSI-X instead of using
pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX).
Access to PCIe device config space again will consume more time.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Nithin Nayak Sujir <nsujir@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI core will initialize device MSI/MSI-X capability in
pci_msi_init_pci_dev(). So device driver should use
pci_dev->msi_cap/msix_cap to determine whether the device
support MSI/MSI-X instead of using
pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX).
Access to PCIe device config space again will consume more time.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Manish Chopra <manish.chopra@qlogic.com>
Cc: Sony Chacko <sony.chacko@qlogic.com>
Cc: Rajesh Borundia <rajesh.borundia@qlogic.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI core will initialize device MSI/MSI-X capability in
pci_msi_init_pci_dev(). So device driver should use
pci_dev->msi_cap/msix_cap to determine whether the device
support MSI/MSI-X instead of using
pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX).
Access to PCIe device config space again will consume more time.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Andrew Gallatin <gallatin@myri.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI core will initialize device MSI/MSI-X capability in
pci_msi_init_pci_dev(). So device driver should use
pci_dev->msi_cap/msix_cap to determine whether the device
support MSI/MSI-X instead of using
pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX).
Access to PCIe device config space again will consume more time.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: netdev@vger.kernel.org
Acked-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI core will initialize device MSI/MSI-X capability in
pci_msi_init_pci_dev(). So device driver should use
pci_dev->msi_cap/msix_cap to determine whether the device
support MSI/MSI-X instead of using
pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX).
Access to PCIe device config space again will consume more time.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixed the condition of extend_desc for jumbo frame.
There is no check routine for extend_desc in the stmmac_jumbo_frm function.
Even though extend_desc is set if dma_tx is used instead of dma_etx.
It causes kernel panic.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
WoL and power state changes will now be done in the shutdown handler.
open/close/ethtool will no longer change the power state. NVRAM
operations can now be permitted whether the device is up or down.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate MAC and PHY WoL setup code into a separate function.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
by closing the device if necessary. Otherwise, since NAPI state is
already disabled, a subsequent close will hang the system.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup gfar_start_xmit()'s fast path by factoring out "redundant"
FCB insertion code (repeated gfar_add_fcb() calls and related)
and by reducing the number of if() clauses (i.e. if(fcb) checks).
Improve maintainability (e.g. there's less code and easier to read)
also by introducing do_csum and do_vlan to mark the other 2 Tx TOE
functionalities, following the same model as do_tstamp.
fcb_len may also be 0 now, to mark that Tx FCB insertion conditions
(do_csum, do_vlan, do_tstamp) have not been met.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both [eTSEC76] and [eTSEC12] errata relate to Tx checksum generation
(for some MPC83xx and MCP8548 older revisions). They require the same
workaround: manual checksum computation and insertion, and disabling
the H/W Tx csum acceleration feature (per frame) through Tx FCB
(Frame Control Block) csum offload settings.
The workaround for [eTSEC76] needs to be fixed because it currently
fails to disable H/W Tx csum insertion via FCB. This patch fixes it
and provides a common workaround implementation for both Tx csum errata.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new IP version has a minor changes and the offsets are same as the
previous version, so adding new IP version support in the driver.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing unlock before return from function tile_net_open()
in the error handling case.
Introduced by commit f3286a3af8.
(tile: support multiple mPIPE shims in tilegx network driver)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These local functions are used only in this file.
Fix the following sparse warnings:
drivers/net/ethernet/mellanox/mlx4/cmd.c:803:5: warning: symbol 'MLX4_CMD_UPDATE_QP_wrapper' was not declared. Should it be static?
drivers/net/ethernet/mellanox/mlx4/cmd.c:812:5: warning: symbol 'MLX4_CMD_GET_OP_REQ_wrapper' was not declared. Should it be static?
drivers/net/ethernet/mellanox/mlx4/cmd.c:1547:5: warning: symbol 'mlx4_master_immediate_activate_vlan_qos' was not declared. Should
it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These local functions are used only in this file.
Fix the following sparse warnings:
drivers/net/ethernet/micrel/ks8842.c:708:6: warning: symbol 'ks8842_handle_rx' was not declared. Should it be static?
drivers/net/ethernet/micrel/ks8842.c:718:6: warning: symbol 'ks8842_handle_tx' was not declared. Should it be static?
drivers/net/ethernet/micrel/ks8842.c:727:6: warning: symbol 'ks8842_handle_rx_overrun' was not declared. Should it be static?
drivers/net/ethernet/micrel/ks8842.c:735:6: warning: symbol 'ks8842_tasklet' was not declared. Should it be static?
drivers/net/ethernet/micrel/ks8851_mll.c:691:6: warning: symbol 'ks_enable_qmu' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These local functions are used only in this file.
Fix the following sparse warnings:
drivers/net/ethernet/emulex/benet/be_main.c:475:6: warning: symbol 'populate_erx_stats' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_main.c:1485:6: warning: symbol 'be_rx_compl_process_gro' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_main.c:2262:5: warning: symbol 'be_poll' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_main.c:3223:6: warning: symbol 'flash_cookie' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_main.c:3280:27: warning: symbol 'get_fsec_info' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_cmds.c:1013:5: warning: symbol 'be_cmd_mccq_ext_create' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_cmds.c:1071:5: warning: symbol 'be_cmd_mccq_org_create' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_cmds.c:3166:5: warning: symbol 'be_cmd_get_profile_config_mbox' was not declared. Should it be
static?
drivers/net/ethernet/emulex/benet/be_cmds.c:3194:5: warning: symbol 'be_cmd_get_profile_config_mccq' was not declared. Should it be
static?
drivers/net/ethernet/emulex/benet/be_roce.c:96:6: warning: symbol '_be_roce_dev_remove' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_roce.c:113:6: warning: symbol '_be_roce_dev_open' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_roce.c:129:6: warning: symbol '_be_roce_dev_close' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bna_rx_sm_stop_wait_entry(), bna_rx_sm_rxf_stop_wait_entry(),
bna_rx_sm_started_entry(), bna_rx_sm_cleanup_wait_entry(),
and bna_rx_sm_cleanup_wait() are used only in this file.
Fix the following sparse warnings:
drivers/net/ethernet/brocade/bna/bna_tx_rx.c:1423:1: warning: symbol 'bna_rx_sm_stop_wait_entry' was not declared. Should it be
static?
drivers/net/ethernet/brocade/bna/bna_tx_rx.c:1476:1: warning: symbol 'bna_rx_sm_rxf_stop_wait_entry' was not declared. Should it be
static?
drivers/net/ethernet/brocade/bna/bna_tx_rx.c:1532:1: warning: symbol 'bna_rx_sm_started_entry' was not declared. Should it be
static?
drivers/net/ethernet/brocade/bna/bna_tx_rx.c:1597:1: warning: symbol 'bna_rx_sm_cleanup_wait_entry' was not declared. Should it be
static?
drivers/net/ethernet/brocade/bna/bna_tx_rx.c:1602:1: warning: symbol 'bna_rx_sm_cleanup_wait' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove this code, per Dave Miller's request, since it is not being used
anywhere in the kernel.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following is needed as well to fix warning/error about shifting a 32 bit
value 32 bits which occurs if building on 32 bit platform caused by conversion
to using dma_addr_t
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
