KMSAN sysbot detected a read access to an untinitialized value in the
headroom of an outgoing CAN related sk_buff. When using CAN sockets this
area is filled appropriately - but when using a packet socket this
initialization is missing.
The problematic read access occurs in the CAN receive path which can
only be triggered when the sk_buff is sent through a (virtual) CAN
interface. So we check in the sending path whether we need to perform
the missing initializations.
Fixes: d3b58c47d3 ("can: replace timestamp as unique skb attribute")
Reported-by: syzbot+b02ff0707a97e4e79ebb@syzkaller.appspotmail.com
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.1
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Pull networking fixes from David Miller:
1) Fix big endian overflow in nf_flow_table, from Arnd Bergmann.
2) Fix port selection on big endian in nft_tproxy, from Phil Sutter.
3) Fix precision tracking for unbound scalars in bpf verifier, from
Daniel Borkmann.
4) Fix integer overflow in socket rcvbuf check in UDP, from Antonio
Messina.
5) Do not perform a neigh confirmation during a pmtu update over a
tunnel, from Hangbin Liu.
6) Fix DMA mapping leak in dpaa_eth driver, from Madalin Bucur.
7) Various PTP fixes for sja1105 dsa driver, from Vladimir Oltean.
8) Add missing to dummy definition of of_mdiobus_child_is_phy(), from
Geert Uytterhoeven
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (54 commits)
hsr: fix slab-out-of-bounds Read in hsr_debugfs_rename()
net/sched: add delete_empty() to filters and use it in cls_flower
tcp: Fix highest_sack and highest_sack_seq
ptp: fix the race between the release of ptp_clock and cdev
net: dsa: sja1105: Reconcile the meaning of TPID and TPID2 for E/T and P/Q/R/S
Documentation: net: dsa: sja1105: Remove text about taprio base-time limitation
net: dsa: sja1105: Remove restriction of zero base-time for taprio offload
net: dsa: sja1105: Really make the PTP command read-write
net: dsa: sja1105: Take PTP egress timestamp by port, not mgmt slot
cxgb4/cxgb4vf: fix flow control display for auto negotiation
mlxsw: spectrum: Use dedicated policer for VRRP packets
mlxsw: spectrum_router: Skip loopback RIFs during MAC validation
net: stmmac: dwmac-meson8b: Fix the RGMII TX delay on Meson8b/8m2 SoCs
net/sched: act_mirred: Pull mac prior redir to non mac_header_xmit device
net_sched: sch_fq: properly set sk->sk_pacing_status
bnx2x: Fix accounting of vlan resources among the PFs
bnx2x: Use appropriate define for vlan credit
of: mdio: Add missing inline to of_mdiobus_child_is_phy() dummy
net: phy: aquantia: add suspend / resume ops for AQR105
dpaa_eth: fix DMA mapping leak
...
In a case when a ptp chardev (like /dev/ptp0) is open but an underlying
device is removed, closing this file leads to a race. This reproduces
easily in a kvm virtual machine:
ts# cat openptp0.c
int main() { ... fp = fopen("/dev/ptp0", "r"); ... sleep(10); }
ts# uname -r
5.5.0-rc3-46cf053e
ts# cat /proc/cmdline
... slub_debug=FZP
ts# modprobe ptp_kvm
ts# ./openptp0 &
[1] 670
opened /dev/ptp0, sleeping 10s...
ts# rmmod ptp_kvm
ts# ls /dev/ptp*
ls: cannot access '/dev/ptp*': No such file or directory
ts# ...woken up
[ 48.010809] general protection fault: 0000 [#1] SMP
[ 48.012502] CPU: 6 PID: 658 Comm: openptp0 Not tainted 5.5.0-rc3-46cf053e #25
[ 48.014624] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), ...
[ 48.016270] RIP: 0010:module_put.part.0+0x7/0x80
[ 48.017939] RSP: 0018:ffffb3850073be00 EFLAGS: 00010202
[ 48.018339] RAX: 000000006b6b6b6b RBX: 6b6b6b6b6b6b6b6b RCX: ffff89a476c00ad0
[ 48.018936] RDX: fffff65a08d3ea08 RSI: 0000000000000247 RDI: 6b6b6b6b6b6b6b6b
[ 48.019470] ... ^^^ a slub poison
[ 48.023854] Call Trace:
[ 48.024050] __fput+0x21f/0x240
[ 48.024288] task_work_run+0x79/0x90
[ 48.024555] do_exit+0x2af/0xab0
[ 48.024799] ? vfs_write+0x16a/0x190
[ 48.025082] do_group_exit+0x35/0x90
[ 48.025387] __x64_sys_exit_group+0xf/0x10
[ 48.025737] do_syscall_64+0x3d/0x130
[ 48.026056] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 48.026479] RIP: 0033:0x7f53b12082f6
[ 48.026792] ...
[ 48.030945] Modules linked in: ptp i6300esb watchdog [last unloaded: ptp_kvm]
[ 48.045001] Fixing recursive fault but reboot is needed!
This happens in:
static void __fput(struct file *file)
{ ...
if (file->f_op->release)
file->f_op->release(inode, file); <<< cdev is kfree'd here
if (unlikely(S_ISCHR(inode->i_mode) && inode->i_cdev != NULL &&
!(mode & FMODE_PATH))) {
cdev_put(inode->i_cdev); <<< cdev fields are accessed here
Namely:
__fput()
posix_clock_release()
kref_put(&clk->kref, delete_clock) <<< the last reference
delete_clock()
delete_ptp_clock()
kfree(ptp) <<< cdev is embedded in ptp
cdev_put
module_put(p->owner) <<< *p is kfree'd, bang!
Here cdev is embedded in posix_clock which is embedded in ptp_clock.
The race happens because ptp_clock's lifetime is controlled by two
refcounts: kref and cdev.kobj in posix_clock. This is wrong.
Make ptp_clock's sysfs device a parent of cdev with cdev_device_add()
created especially for such cases. This way the parent device with its
ptp_clock is not released until all references to the cdev are released.
This adds a requirement that an initialized but not exposed struct
device should be provided to posix_clock_register() by a caller instead
of a simple dev_t.
This approach was adopted from the commit 72139dfa24 ("watchdog: Fix
the race between the release of watchdog_core_data and cdev"). See
details of the implementation in the commit 233ed09d7f ("chardev: add
helper function to register char devs with a struct device").
Link: https://lore.kernel.org/linux-fsdevel/20191125125342.6189-1-vdronov@redhat.com/T/#u
Analyzed-by: Stephen Johnston <sjohnsto@redhat.com>
Analyzed-by: Vern Lovejoy <vlovejoy@redhat.com>
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_OF_MDIO=n:
drivers/net/phy/mdio_bus.c:23:
include/linux/of_mdio.h:58:13: warning: ‘of_mdiobus_child_is_phy’ defined but not used [-Wunused-function]
static bool of_mdiobus_child_is_phy(struct device_node *child)
^~~~~~~~~~~~~~~~~~~~~~~
Fix this by adding the missing "inline" keyword.
Fixes: 0aa4d016c0 ("of: mdio: export of_mdiobus_child_is_phy")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 6bb86fefa0
("libahci_platform: Staticize ahci_platform_<en/dis>able_phys()") we are
going to need ahci_platform_{enable,disable}_phys() in a subsequent
commit for ahci_brcm.c in order to properly control the PHY
initialization order.
Also make sure the function prototypes are declared in
include/linux/ahci_platform.h as a result.
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
ata_qc_complete_multiple() is called with a mask of the still active
tags.
mv_sata doesn't have this information directly and instead calculates
the still active tags from the started tags (ap->qc_active) and the
finished tags as (ap->qc_active ^ done_mask)
Since 28361c4036 the hw_tag and tag are no longer the same and the
equation is no longer valid. In ata_exec_internal_sg() ap->qc_active is
initialized as 1ULL << ATA_TAG_INTERNAL, but in hardware tag 0 is
started and this will be in done_mask on completion. ap->qc_active ^
done_mask becomes 0x100000000 ^ 0x1 = 0x100000001 and thus tag 0 used as
the internal tag will never be reported as completed.
This is fixed by introducing ata_qc_get_active() which returns the
active hardware tags and calling it where appropriate.
This is tested on mv_sata, but sata_fsl and sata_nv suffer from the same
problem. There is another case in sata_nv that most likely needs fixing
as well, but this looks a little different, so I wasn't confident enough
to change that.
Fixes: 28361c4036 ("libata: add extra internal command")
Cc: stable@vger.kernel.org
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add missing export of ata_qc_get_active(), as per Pali.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull ext4 bug fixes from Ted Ts'o:
"Ext4 bug fixes, including a regression fix"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: clarify impact of 'commit' mount option
ext4: fix unused-but-set-variable warning in ext4_add_entry()
jbd2: fix kernel-doc notation warning
ext4: use RCU API in debug_print_tree
ext4: validate the debug_want_extra_isize mount option at parse time
ext4: reserve revoke credits in __ext4_new_inode
ext4: unlock on error in ext4_expand_extra_isize()
ext4: optimize __ext4_check_dir_entry()
ext4: check for directory entries too close to block end
ext4: fix ext4_empty_dir() for directories with holes
Pull networking fixes from David Miller:
1) Several nf_flow_table_offload fixes from Pablo Neira Ayuso,
including adding a missing ipv6 match description.
2) Several heap overflow fixes in mwifiex from qize wang and Ganapathi
Bhat.
3) Fix uninit value in bond_neigh_init(), from Eric Dumazet.
4) Fix non-ACPI probing of nxp-nci, from Stephan Gerhold.
5) Fix use after free in tipc_disc_rcv(), from Tuong Lien.
6) Enforce limit of 33 tail calls in mips and riscv JIT, from Paul
Chaignon.
7) Multicast MAC limit test is off by one in qede, from Manish Chopra.
8) Fix established socket lookup race when socket goes from
TCP_ESTABLISHED to TCP_LISTEN, because there lacks an intervening
RCU grace period. From Eric Dumazet.
9) Don't send empty SKBs from tcp_write_xmit(), also from Eric Dumazet.
10) Fix active backup transition after link failure in bonding, from
Mahesh Bandewar.
11) Avoid zero sized hash table in gtp driver, from Taehee Yoo.
12) Fix wrong interface passed to ->mac_link_up(), from Russell King.
13) Fix DSA egress flooding settings in b53, from Florian Fainelli.
14) Memory leak in gmac_setup_txqs(), from Navid Emamdoost.
15) Fix double free in dpaa2-ptp code, from Ioana Ciornei.
16) Reject invalid MTU values in stmmac, from Jose Abreu.
17) Fix refcount leak in error path of u32 classifier, from Davide
Caratti.
18) Fix regression causing iwlwifi firmware crashes on boot, from Anders
Kaseorg.
19) Fix inverted return value logic in llc2 code, from Chan Shu Tak.
20) Disable hardware GRO when XDP is attached to qede, frm Manish
Chopra.
21) Since we encode state in the low pointer bits, dst metrics must be
at least 4 byte aligned, which is not necessarily true on m68k. Add
annotations to fix this, from Geert Uytterhoeven.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (160 commits)
sfc: Include XDP packet headroom in buffer step size.
sfc: fix channel allocation with brute force
net: dst: Force 4-byte alignment of dst_metrics
selftests: pmtu: fix init mtu value in description
hv_netvsc: Fix unwanted rx_table reset
net: phy: ensure that phy IDs are correctly typed
mod_devicetable: fix PHY module format
qede: Disable hardware gro when xdp prog is installed
net: ena: fix issues in setting interrupt moderation params in ethtool
net: ena: fix default tx interrupt moderation interval
net/smc: unregister ib devices in reboot_event
net: stmmac: platform: Fix MDIO init for platforms without PHY
llc2: Fix return statement of llc_stat_ev_rx_null_dsap_xid_c (and _test_c)
net: hisilicon: Fix a BUG trigered by wrong bytes_compl
net: dsa: ksz: use common define for tag len
s390/qeth: don't return -ENOTSUPP to userspace
s390/qeth: fix promiscuous mode after reset
s390/qeth: handle error due to unsupported transport mode
cxgb4: fix refcount init for TC-MQPRIO offload
tc-testing: initial tdc selftests for cls_u32
...
PHY IDs are 32-bit unsigned quantities. Ensure that they are always
treated as such, and not passed around as "int"s.
Fixes: 13d0ab6750 ("net: phy: check return code when requesting PHY driver module")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a PHY is probed, if the top bit is set, we end up requesting a
module with the string "mdio:-10101110000000100101000101010001" -
the top bit is printed to a signed -1 value. This leads to the module
not being loaded.
Fix the module format string and the macro generating the values for
it to ensure that we only print unsigned types and the top bit is
always 0/1. We correctly end up with
"mdio:10101110000000100101000101010001".
Fixes: 8626d3b432 ("phylib: Support phy module autoloading")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch exports of_mdiobus_child_is_phy, allowing to check if a child
node is a network PHY.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2019-12-19
The following pull-request contains BPF updates for your *net* tree.
We've added 10 non-merge commits during the last 8 day(s) which contain
a total of 21 files changed, 269 insertions(+), 108 deletions(-).
The main changes are:
1) Fix lack of synchronization between xsk wakeup and destroying resources
used by xsk wakeup, from Maxim Mikityanskiy.
2) Fix pruning with tail call patching, untrack programs in case of verifier
error and fix a cgroup local storage tracking bug, from Daniel Borkmann.
3) Fix clearing skb->tstamp in bpf_redirect() when going from ingress to
egress which otherwise cause issues e.g. on fq qdisc, from Lorenz Bauer.
4) Fix compile warning of unused proc_dointvec_minmax_bpf_restricted() when
only cBPF is present, from Alexander Lobakin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge fixes from Andrew Morton:
"6 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
lib/Kconfig.debug: fix some messed up configurations
mm: vmscan: protect shrinker idr replace with CONFIG_MEMCG
kasan: don't assume percpu shadow allocations will succeed
kasan: use apply_to_existing_page_range() for releasing vmalloc shadow
mm/memory.c: add apply_to_existing_page_range() helper
kasan: fix crashes on access to memory mapped by vm_map_ram()
Pull power management fix from Rafael Wysocki:
"Fix a problem related to CPU offline/online and cpufreq governors that
in some system configurations may lead to a system-wide deadlock
during CPU online"
* tag 'pm-5.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: Avoid leaving stale IRQ work items during CPU offline
Pull tpm fixes from Jarkko Sakkinen:
"Bunch of fixes for rc3"
* tag 'tpmdd-next-20191219' of git://git.infradead.org/users/jjs/linux-tpmdd:
tpm/tpm_ftpm_tee: add shutdown call back
tpm: selftest: cleanup after unseal with wrong auth/policy test
tpm: selftest: add test covering async mode
tpm: fix invalid locking in NONBLOCKING mode
security: keys: trusted: fix lost handle flush
tpm_tis: reserve chip for duration of tpm_tis_core_init
KEYS: asymmetric: return ENOMEM if akcipher_request_alloc() fails
KEYS: remove CONFIG_KEYS_COMPAT
Fix missing '*' kernel-doc notation that causes this warning:
../include/linux/netdevice.h:1779: warning: bad line: spinlock
Fixes: ab92d68fc2 ("net: core: add generic lockdep keys")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
apply_to_page_range() takes an address range, and if any parts of it are
not covered by the existing page table hierarchy, it allocates memory to
fill them in.
In some use cases, this is not what we want - we want to be able to
operate exclusively on PTEs that are already in the tables.
Add apply_to_existing_page_range() for this. Adjust the walker
functions for apply_to_page_range to take 'create', which switches them
between the old and new modes.
This will be used in KASAN vmalloc.
[akpm@linux-foundation.org: reduce code duplication]
[akpm@linux-foundation.org: s/apply_to_existing_pages/apply_to_existing_page_range/]
[akpm@linux-foundation.org: initialize __apply_to_page_range::err]
Link: http://lkml.kernel.org/r/20191205140407.1874-1-dja@axtens.net
Signed-off-by: Daniel Axtens <dja@axtens.net>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Uladzislau Rezki (Sony) <urezki@gmail.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Daniel Axtens <dja@axtens.net>
Cc: Qian Cai <cai@lca.pw>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull EFI fixes from Ingo Molnar:
"Protect presistent EFI memory reservations from kexec, fix EFIFB early
console, EFI stub graphics output fixes and other misc fixes."
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: Don't attempt to map RCI2 config table if it doesn't exist
efi/earlycon: Remap entire framebuffer after page initialization
efi: Fix efi_loaded_image_t::unload type
efi/gop: Fix memory leak in __gop_query32/64()
efi/gop: Return EFI_SUCCESS if a usable GOP was found
efi/gop: Return EFI_NOT_FOUND if there are no usable GOPs
efi/memreserve: Register reservations as 'reserved' in /proc/iomem
Recently noticed that we're tracking programs related to local storage maps
through their prog pointer. This is a wrong assumption since the prog pointer
can still change throughout the verification process, for example, whenever
bpf_patch_insn_single() is called.
Therefore, the prog pointer that was assigned via bpf_cgroup_storage_assign()
is not guaranteed to be the same as we pass in bpf_cgroup_storage_release()
and the map would therefore remain in busy state forever. Fix this by using
the prog's aux pointer which is stable throughout verification and beyond.
Fixes: de9cbbaadb ("bpf: introduce cgroup storage maps")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: Roman Gushchin <guro@fb.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/1471c69eca3022218666f909bc927a92388fd09e.1576580332.git.daniel@iogearbox.net
The original code, before it was moved into security/keys/trusted-keys
had a flush after the blob unseal. Without that flush, the volatile
handles increase in the TPM until it becomes unusable and the system
either has to be rebooted or the TPM volatile area manually flushed.
Fix by adding back the lost flush, which we now have to export because
of the relocation of the trusted key code may cause the consumer to be
modular.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fixes: 2e19e10131 ("KEYS: trusted: Move TPM2 trusted keys code")
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Pull ARM SoC fixes from Olof Johansson:
"I didn't get a batch in this weekend, so here's what we queued up last
week and today.
- A couple of defconfigs add back debugfs -- it used to be implicitly
enabled through CONFIG_TRACING, but 0e4a459f56 ("tracing:
Remove unnecessary DEBUG_FS dependency") removed that.
- The rest are mostly minor fixlets of the usual kind; some DT
tweaks, a headerfile refactor that needs a build fix now, etc"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (30 commits)
ARM: bcm: Add missing sentinel to bcm2711_compat[]
ARM: shmobile: defconfig: Restore debugfs support
bus: ti-sysc: Fix missing reset delay handling
ARM: imx: Fix boot crash if ocotp is not found
ARM: imx_v6_v7_defconfig: Explicitly restore CONFIG_DEBUG_FS
ARM: dts: imx6ul-evk: Fix peripheral regulator
arm64: dts: ls1028a: fix reboot node
ARM: mmp: include the correct cputype.h
ARM: dts: am437x-gp/epos-evm: fix panel compatible
arm64: dts: ls1028a: fix typo in TMU calibration data
ARM: imx: Correct ocotp id for serial number support of i.MX6ULL/ULZ SoCs
ARM: dts: bcm283x: Fix critical trip point
ARM: omap2plus_defconfig: Add back DEBUG_FS
ARM: omap2plus_defconfig: enable NET_SWITCHDEV
ARM: dts: am335x-sancloud-bbe: fix phy mode
bus: ti-sysc: Fix missing force mstandby quirk handling
reset: Do not register resource data for missing resets
reset: Fix {of,devm}_reset_control_array_get kerneldoc return types
reset: brcmstb: Remove resource checks
dt-bindings: reset: Fix brcmstb-reset example
...
Commit da765a2f59 ("bpf: Add poke dependency tracking for prog array
maps") wrongly assumed that in case of prog load errors, we're cleaning
up all program tracking via bpf_free_used_maps().
However, it can happen that we're still at the point where we didn't copy
map pointers into the prog's aux section such that env->prog->aux->used_maps
is still zero, running into a UAF. In such case, the verifier has similar
release_maps() helper that drops references to used maps from its env.
Consolidate the release code into __bpf_free_used_maps() and call it from
all sides to fix it.
Fixes: da765a2f59 ("bpf: Add poke dependency tracking for prog array maps")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/1c2909484ca524ae9f55109b06f22b6213e76376.1576514756.git.daniel@iogearbox.net
Pull ksys_mount() and ksys_dup() removal from Dominik Brodowski:
"This small series replaces all in-kernel calls to the
userspace-focused ksys_mount() and ksys_dup() with calls to
kernel-centric functions:
For each replacement of ksys_mount() with do_mount(), one needs to
verify that the first and third parameter (char *dev_name, char *type)
are strings allocated in kernelspace and that the fifth parameter
(void *data) is either NULL or refers to a full page (only occurence
in init/do_mounts.c::do_mount_root()). The second and fourth
parameters (char *dir_name, unsigned long flags) are passed by
ksys_mount() to do_mount() unchanged, and therefore do not require
particular care.
Moreover, instead of pretending to be userspace, the opening of
/dev/console as stdin/stdout/stderr can be implemented using in-kernel
functions as well. Thereby, ksys_dup() can be removed for good"
[ This doesn't get rid of the special "kernel init runs with KERNEL_DS"
case, but it at least removes _some_ of the users of "treat kernel
pointers as user pointers for our magical init sequence".
One day we'll hopefully be rid of it all, and can initialize our
init_thread addr_limit to USER_DS. - Linus ]
* 'remove-ksys-mount-dup' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/linux:
fs: remove ksys_dup()
init: unify opening /dev/console as stdin/stdout/stderr
init: use do_mount() instead of ksys_mount()
initrd: use do_mount() instead of ksys_mount()
devtmpfs: use do_mount() instead of ksys_mount()
Michal Kubecek and Firo Yang did a very nice analysis of crashes
happening in __inet_lookup_established().
Since a TCP socket can go from TCP_ESTABLISH to TCP_LISTEN
(via a close()/socket()/listen() cycle) without a RCU grace period,
I should not have changed listeners linkage in their hash table.
They must use the nulls protocol (Documentation/RCU/rculist_nulls.txt),
so that a lookup can detect a socket in a hash list was moved in
another one.
Since we added code in commit d296ba60d8 ("soreuseport: Resolve
merge conflict for v4/v6 ordering fix"), we have to add
hlist_nulls_add_tail_rcu() helper.
Fixes: 3b24d854cb ("tcp/dccp: do not touch listener sk_refcnt under synflood")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Michal Kubecek <mkubecek@suse.cz>
Reported-by: Firo Yang <firo.yang@suse.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Link: https://lore.kernel.org/netdev/20191120083919.GH27852@unicorn.suse.cz/
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Pull i2c updates from Wolfram Sang:
- removal of an old API where all in-kernel users have been converted
as of this merge window.
- a kdoc fix
- a new helper that will make dependencies for the next API conversion
a tad easier
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: add helper to check if a client has a driver attached
i2c: fix header file kernel-doc warning
i2c: remove i2c_new_dummy() API
Pull power management fixes from Rafael Wysocki:
"These add PM QoS support to devfreq and fix a few issues in that
subsystem, fix two cpuidle issues and do one minor cleanup in there,
and address an ACPI power management problem related to devices with
special power management requirements, like fans.
Specifics:
- Add PM QoS support, based on the frequency QoS introduced during
the 5.4 cycle, to devfreq (Leonard Crestez).
- Fix some assorted devfreq issues (Leonard Crestez).
- Fix an unintentional cpuidle behavior change (introduced during the
5.4 cycle) related to the active polling time limit (Marcelo
Tosatti).
- Fix a recently introduced cpuidle helper function and do a minor
cleanup in the cpuidle core (Rafael Wysocki).
- Avoid adding devices with special power management requirements,
like fans, to the generic ACPI PM domain (Rafael Wysocki)"
* tag 'pm-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: Drop unnecessary type cast in cpuidle_poll_time()
cpuidle: Fix cpuidle_driver_state_disabled()
ACPI: PM: Avoid attaching ACPI PM domain to certain devices
cpuidle: use first valid target residency as poll time
PM / devfreq: Use PM QoS for sysfs min/max_freq
PM / devfreq: Add PM QoS support
PM / devfreq: Don't fail devfreq_dev_release if not in list
PM / devfreq: Introduce get_freq_range helper
PM / devfreq: Set scaling_max_freq to max on OPP notifier error
PM / devfreq: Fix devfreq_notifier_call returning errno
Pull block fixes from Jens Axboe:
- stable fix for the bi_size overflow. Not a corruption issue, but a
case wher we could merge but disallowed (Andreas)
- NVMe pull request via Keith, with various fixes.
- MD pull request from Song.
- Merge window regression fix for the rq passthrough stats (Logan)
- Remove unused blkcg_drain_queue() function (Guoqing)
* tag 'for-linus-20191212' of git://git.kernel.dk/linux-block:
blk-cgroup: remove blkcg_drain_queue
block: fix NULL pointer dereference in account statistics with IDE
md: make sure desc_nr less than MD_SB_DISKS
md: raid1: check rdev before reference in raid1_sync_request func
raid5: need to set STRIPE_HANDLE for batch head
block: fix "check bi_size overflow before merge"
nvme/pci: Fix read queue count
nvme/pci Limit write queue sizes to possible cpus
nvme/pci: Fix write and poll queue types
nvme/pci: Remove last_cq_head
nvme: Namepace identification descriptor list is optional
nvme-fc: fix double-free scenarios on hw queues
nvme: else following return is not needed
nvme: add error message on mismatching controller ids
nvme_fc: add module to ops template to allow module references
nvmet-loop: Avoid preallocating big SGL for data
nvme-fc: Avoid preallocating big SGL for data
nvme-rdma: Avoid preallocating big SGL for data
Pull FIELD_SIZEOF conversion from Kees Cook:
"A mostly mechanical treewide conversion from FIELD_SIZEOF() to
sizeof_field(). This avoids the redundancy of having 2 macros
(actually 3) doing the same thing, and consolidates on sizeof_field().
While "field" is not an accurate name, it is the common name used in
the kernel, and doesn't result in any unintended innuendo.
As there are still users of FIELD_SIZEOF() in -next, I will clean up
those during this coming development cycle and send the final old
macro removal patch at that time"
* tag 'sizeof_field-v5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
treewide: Use sizeof_field() macro
MIPS: OCTEON: Replace SIZEOF_FIELD() macro
ksys_dup() is used only at one place in the kernel, namely to duplicate
fd 0 of /dev/console to stdout and stderr. The same functionality can be
achieved by using functions already available within the kernel namespace.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The scheduler code calling cpufreq_update_util() may run during CPU
offline on the target CPU after the IRQ work lists have been flushed
for it, so the target CPU should be prevented from running code that
may queue up an IRQ work item on it at that point.
Unfortunately, that may not be the case if dvfs_possible_from_any_cpu
is set for at least one cpufreq policy in the system, because that
allows the CPU going offline to run the utilization update callback
of the cpufreq governor on behalf of another (online) CPU in some
cases.
If that happens, the cpufreq governor callback may queue up an IRQ
work on the CPU running it, which is going offline, and the IRQ work
may not be flushed after that point. Moreover, that IRQ work cannot
be flushed until the "offlining" CPU goes back online, so if any
other CPU calls irq_work_sync() to wait for the completion of that
IRQ work, it will have to wait until the "offlining" CPU is back
online and that may not happen forever. In particular, a system-wide
deadlock may occur during CPU online as a result of that.
The failing scenario is as follows. CPU0 is the boot CPU, so it
creates a cpufreq policy and becomes the "leader" of it
(policy->cpu). It cannot go offline, because it is the boot CPU.
Next, other CPUs join the cpufreq policy as they go online and they
leave it when they go offline. The last CPU to go offline, say CPU3,
may queue up an IRQ work while running the governor callback on
behalf of CPU0 after leaving the cpufreq policy because of the
dvfs_possible_from_any_cpu effect described above. Then, CPU0 is
the only online CPU in the system and the stale IRQ work is still
queued on CPU3. When, say, CPU1 goes back online, it will run
irq_work_sync() to wait for that IRQ work to complete and so it
will wait for CPU3 to go back online (which may never happen even
in principle), but (worse yet) CPU0 is waiting for CPU1 at that
point too and a system-wide deadlock occurs.
To address this problem notice that CPUs which cannot run cpufreq
utilization update code for themselves (for example, because they
have left the cpufreq policies that they belonged to), should also
be prevented from running that code on behalf of the other CPUs that
belong to a cpufreq policy with dvfs_possible_from_any_cpu set and so
in that case the cpufreq_update_util_data pointer of the CPU running
the code must not be NULL as well as for the CPU which is the target
of the cpufreq utilization update in progress.
Accordingly, change cpufreq_this_cpu_can_update() into a regular
function in kernel/sched/cpufreq.c (instead of a static inline in a
header file) and make it check the cpufreq_update_util_data pointer
of the local CPU if dvfs_possible_from_any_cpu is set for the target
cpufreq policy.
Also update the schedutil governor to do the
cpufreq_this_cpu_can_update() check in the non-fast-switch
case too to avoid the stale IRQ work issues.
Fixes: 99d14d0e16 ("cpufreq: Process remote callbacks from any CPU if the platform permits")
Link: https://lore.kernel.org/linux-pm/20191121093557.bycvdo4xyinbc5cb@vireshk-i7/
Reported-by: Anson Huang <anson.huang@nxp.com>
Tested-by: Anson Huang <anson.huang@nxp.com>
Cc: 4.14+ <stable@vger.kernel.org> # 4.14+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Peng Fan <peng.fan@nxp.com> (i.MX8QXP-MEK)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since blk_drain_queue had already been removed, so this function
is not needed anymore.
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In prepare_namespace(), do_mount() can be used instead of ksys_mount()
as the first and third argument are const strings in the kernel, the
second and fourth argument are passed through anyway, and the fifth
argument is NULL.
In do_mount_root(), ksys_mount() is called with the first and third
argument being already kernelspace strings, which do not need to be
copied over from userspace to kernelspace (again). The second and
fourth arguments are passed through to do_mount() anyway. The fifth
argument, while already residing in kernelspace, needs to be put into
a page of its own. Then, do_mount() can be used instead of
ksys_mount().
Once this is done, there are no in-kernel users to ksys_mount() left,
which can therefore be removed.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
In devtmpfs, do_mount() can be called directly instead of complex wrapping
by ksys_mount():
- the first and third arguments are const strings in the kernel,
and do not need to be copied over from userspace;
- the fifth argument is NULL, and therefore no page needs to be
copied over from userspace;
- the second and fourth argument are passed through anyway.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Make BPF trampoline attach its generated assembly code to kernel functions via
register_ftrace_direct() API. It helps ftrace-based tracers co-exist with BPF
trampoline on the same kernel function. It also switches attaching logic from
arch specific text_poke to generic ftrace that is available on many
architectures. text_poke is still necessary for bpf-to-bpf attach and for
bpf_tail_call optimization.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191209000114.1876138-3-ast@kernel.org
Pull tracing fixes from Steven Rostedt:
- Remove code I accidentally applied when doing a minor fix up to a
patch, and then using "git commit -a --amend", which pulled in some
other changes I was playing with.
- Remove an used variable in trace_events_inject code
- Fix function graph tracer when it traces a ftrace direct function.
It will now ignore tracing a function that has a ftrace direct
tramploine attached. This is needed for eBPF to use the ftrace direct
code.
* tag 'trace-v5.5-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace: Fix function_graph tracer interaction with BPF trampoline
tracing: remove set but not used variable 'buffer'
module: Remove accidental change of module_enable_x()
As a preparation for an API conversion, factor out something frequently
used in the media subsystem. As an improvement, it bails out on both,
NULL and ERRPTR to handle the old and new API.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix kernel-doc warning in <linux/i2c.h>.
../include/linux/i2c.h:337: warning: Function parameter or member 'init_irq' not described in 'i2c_client'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Depending on type of BPF programs served by BPF trampoline it can call original
function. In such case the trampoline will skip one stack frame while
returning. That will confuse function_graph tracer and will cause crashes with
bad RIP. Teach graph tracer to skip functions that have BPF trampoline attached.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Commit 03856e928b ("bus: ti-sysc: Handle mstandby quirk and use it for
musb") added quirk handling for mstandby quirk but did not consider that
we also need a quirk variant for SYSC_QUIRK_FORCE_MSTANDBY.
We need to use forced idle mode for both SYSC_QUIRK_SWSUP_MSTANDBY and
SYSC_QUIRK_FORCE_MSTANDBY, but SYSC_QUIRK_SWSUP_MSTANDBY also need to
additionally also configure no-idle mode when enabled.
Fixes: 03856e928b ("bus: ti-sysc: Handle mstandby quirk and use it for musb")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull pr_warning() removal from Petr Mladek.
- Final removal of the unused pr_warning() alias.
You're supposed to use just "pr_warn()" in the kernel.
* tag 'printk-for-5.5-pr-warning-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk:
checkpatch: Drop pr_warning check
printk: Drop pr_warning definition
Fix up for "printk: Drop pr_warning definition"
workqueue: Use pr_warn instead of pr_warning
Replace all the occurrences of FIELD_SIZEOF() with sizeof_field() except
at places where these are defined. Later patches will remove the unused
definition of FIELD_SIZEOF().
This patch is generated using following script:
EXCLUDE_FILES="include/linux/stddef.h|include/linux/kernel.h"
git grep -l -e "\bFIELD_SIZEOF\b" | while read file;
do
if [[ "$file" =~ $EXCLUDE_FILES ]]; then
continue
fi
sed -i -e 's/\bFIELD_SIZEOF\b/sizeof_field/g' $file;
done
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Link: https://lore.kernel.org/r/20190924105839.110713-3-pankaj.laxminarayan.bharadiya@intel.com
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David Miller <davem@davemloft.net> # for net
Switch the handling of min_freq and max_freq from sysfs to use the
dev_pm_qos_request interface.
Since PM QoS handles frequencies as kHz this change reduces the
precision of min_freq and max_freq. This shouldn't introduce problems
because frequencies which are not an integer number of kHz are likely
not an integer number of Hz either.
Try to ensure compatibility by rounding min values down and rounding
max values up.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
[cw00.choi: Return -EAGAIN instead of -EINVAL if dev_pm_qos is inactive]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Register notifiers with the PM QoS framework in order to respond to
requests for DEV_PM_QOS_MIN_FREQUENCY and DEV_PM_QOS_MAX_FREQUENCY.
No notifiers are added by this patch but PM QoS constraints can be
imposed externally (for example from other devices).
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Pull networking fixes from David Miller:
1) More jumbo frame fixes in r8169, from Heiner Kallweit.
2) Fix bpf build in minimal configuration, from Alexei Starovoitov.
3) Use after free in slcan driver, from Jouni Hogander.
4) Flower classifier port ranges don't work properly in the HW offload
case, from Yoshiki Komachi.
5) Use after free in hns3_nic_maybe_stop_tx(), from Yunsheng Lin.
6) Out of bounds access in mqprio_dump(), from Vladyslav Tarasiuk.
7) Fix flow dissection in dsa TX path, from Alexander Lobakin.
8) Stale syncookie timestampe fixes from Guillaume Nault.
[ Did an evil merge to silence a warning introduced by this pull - Linus ]
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits)
r8169: fix rtl_hw_jumbo_disable for RTL8168evl
net_sched: validate TCA_KIND attribute in tc_chain_tmplt_add()
r8169: add missing RX enabling for WoL on RTL8125
vhost/vsock: accept only packets with the right dst_cid
net: phy: dp83867: fix hfs boot in rgmii mode
net: ethernet: ti: cpsw: fix extra rx interrupt
inet: protect against too small mtu values.
gre: refetch erspan header from skb->data after pskb_may_pull()
pppoe: remove redundant BUG_ON() check in pppoe_pernet
tcp: Protect accesses to .ts_recent_stamp with {READ,WRITE}_ONCE()
tcp: tighten acceptance of ACKs not matching a child socket
tcp: fix rejected syncookies due to stale timestamps
lpc_eth: kernel BUG on remove
tcp: md5: fix potential overestimation of TCP option space
net: sched: allow indirect blocks to bind to clsact in TC
net: core: rename indirect block ingress cb function
net-sysfs: Call dev_hold always in netdev_queue_add_kobject
net: dsa: fix flow dissection on Tx path
net/tls: Fix return values to avoid ENOTSUPP
net: avoid an indirect call in ____sys_recvmsg()
...
